Table of Contents
Advertisement
4•9•6 OPTION "O08 - PHIINV"
This option should only be used by your authorised dealer.
This option is used only the first time you switch on your robot, to
choose the correct phase in accordance with the installation of the
boundary wire.
From the "OPTIONS" screen, press # - 8 and use the # key to select
or deselect the option.
O08 PhiInv : " - ", in accordance with the installation.
O08 PhiInv : " √ ", in accordance with the installation.
4•9•7 OPTION "O09 - HEADROTINV"
This option alternates the direction in which the cutting heads rotate
after each mowing cycle.
From the "OPTIONS" screen, press # - 9 and use the # key to select
or deselect the option.
O09 HeadRotInv: " - ", no alternation of direction in which
cutting heads rotate.
O09 HeadRotInv: " √ ", cyclical alternation of direction in
which cutting heads rotate.
4•9•8 OPTION "O10 - CCWSEEK"
This option causes the robot to return to the charging station in a
clockwise direction.
From the "OPTIONS" screen, press # - 9 - F3 and use the # key to
select or deselect the option.
O10 CCWSeek: " - ", return to the charging station in a
clockwise direction.
O10 CCWSeek: " √ ", return to the charging station in an
anticlockwise direction.
If option O11 is selected, option O10 will display the current choice
being used by the robot first, but can be overridden by the user.
4•9•9 OPTION "O11 - CHGE2SIDES"
This option allows the robot to return to the charging station in
either direction.
From the "OPTIONS" screen, press # - 9 - F3 - F3 and use the #
key to select or deselect the option.
O11 Chge2Sides: " - ", return to charging station in one
direction only, as defined by option O010.
O11 Chge2Sides: " √ ", return to charging station in either
direction.
4•9•10 OPTION "O13 - UDOCKING"
This option defines the manoeuvre for returning to the station.
In a "U" return, the robot passes in front of the station before
performing a U-turn to connect to the station.
In an "S" return, the robot returns to the station directly without
passing in front of it first.
From the "OPTIONS" screen, press # - 9 - F3 - F3 - F3 and use the
# key to select or deselect the option.
O13 Udocking: " - ", "S" return manoeuvre.
O13 Udocking: " √ ", "U" return manoeuvre.
4• OPERATING INSTRUCTIONS
4•9•11 OPTION "O14 - BACK ALONG WIRE"
This option defines the station return path.
With Back Along Wire enabled, the robot follows its wire back to
the station.
With Back Along Wire disabled, the robot follows its trackborder
defined at the time of station installation.
From the "OPTIONS" display, press # - 9 - F3 - F3 - F3 - F3 and
use the # key to select or deselect the option.
O14 Back Along Wire: " - ", back along trackborder.
O14 Back Along Wire: " √ ", back along wire.
4•9•12 OPTION "O15 - NO RESTS"
This option disables the machine rest times.
From the "OPTIONS" display, press # - 9 - F3 - F3 - F3 - F3 - F3
and use the # key to select or deselect the option.
O15 No Rests: " - ", rest times observed.
O15 No Rests: " √ ", rest times ignored.
4•9•13 OPTION "O16 - MULTIZONE"
This option enables Multizone operation. Option available depending
on the machine software.
From the "OPTIONS" display, press # - 9 - F3 - F3 - F3 - F3 - F3 -
F3 and use the # key to select or deselect the option.
O16 Multizone: " - ", no multizone.
O16 Multizone: " √ ", multizone enabled.
4•9•14 OPTION "O17 - ENABLE ZONE"
Accessible in Multizone mode only. This option enables the zones
to be mown. Option available depending on the machine software.
From the "OPTIONS" display, press # - 9 - F3 - F3 - F3 - F3 - F3 -
F3 - F3 and use the # key to select or deselect the option.
O17 Enable zone: " - ", zone disabled.
O17 Enable zone: " √ ", zone enabled.
4•9•15 OPTION "O18 - KEYBOARD LOCK"
This option allows you to lock the keyboard.
From the "OPTIONS" display, press # - 9 - F3 - F3 - F3 - F3 - F3 -
F3 - F3 - F3 and use the # key to select or deselect the option.
O18 Keyboard Lock: " - ", keyboard enabled.
O18 Keyboard Lock: " √ ", keyboard locked.
If this option is activated, to use the keyboard you must press key 0
for 5 seconds.
25
Advertisement
Table of Contents
