Table of Contents
Advertisement
ROBOT
Beeps
- 1 long beep: Stop robot or incorrect
key has been pressed
- 1 short beep: Key has been pressed
- 2 long beeps / 10 sec: Charge robot
- 2 short beeps / 1 sec: Cutting heads
starting up
- 1 short beep /2 sec: Alarm
Charge
- FC: Fast Charge, normal mode
- SC: Slow Charge, rest mode
- WU: Wait User
- WT: Wait programmed Timers
- W.BH: Wait Battery too Hot
- W.FT: Wait Freezing ambient
Temperature
An error message is displayed on the screen when the robot mower
ETM105 comes across something unexpected. To return the ETM105
robot mower to operation, see the "Troubleshooting" section and press
key C to delete it.
4•8•2 INFORMATION MESSAGES
It is possible to choose between displaying the time and the
technical information in the "Debug-info" menu by pressing the F3
key on the keypad.
4•8•3 MANUAL CHARGE
If you return the machine to the base station manually, press
before closing the hood once "W.U" is displayed.
4•9 USING OPTIONS
This sub-menu contains 16 options, accessible according to the
configuration of the area to be mown and the robot's firmware.
Options can be selected ' √ ' or deselected ' - ' with the # key by your
dealer to suit your mowing area.
Caution is advised when using this sub-menu as modifications can
significantly alter the effectiveness of the robot.
OPTIONS
Option 00 : Multiple robots
Option 01 : Go charging
Option 02 : Stay on charge
Option 03 : Demo mode
Option 04 : No beep in charge
Option 08 : Signal Phase Inversion
Option 09 : Heads rotation alternated
Option 10 : Counter-clockwise dock seek
Option 11 : Both sides docking
Option 13 : Docking manoeuvre in U
Option 14 : Back along wire
Option 15 : No rests
Option 16 : Multizone
Option 17 : Active zone
Option 18 : Keyboard lock
24
4• OPERATING INSTRUCTIONS
CHARGING STATION
LED
- Blinking green light: OK, normal
mode
- Blinking red light: boundary
wire has been cut or is too long
(usually > 1200 m)
- Continuous red light: failure of
the station's electronic card or
wire is too short (usually < 200m)
- No colour: the station is not
connected to an electricity supply.
DEFAULT
-
-
-
-
-
-
√
-
√
√
-
-
-
√
-
4•9•1 OPTION «O00 - MULTIROBOT»
The "MultiRobot" option must be selected if several robots are
working in the same area.
From the "OPTIONS" screen, press # - F2 and use the # again to
select or deselect the option.
O00 MultiRobot: " - ", the robot will charge at any charging
station.
O00 MultiRobot: " √ ", the robot will only connect to one
specific available station.
In practice, this option must only be selected for specific cases (e.g.
Golf courses).
4•9•2 OPTION "O01 - GOTOCHGE"
This option requires the robot to return immediately to its
charging station. Once the robot's batteries have been recharged, it
automatically starts working again.
From the "MENU" screen, press F1.
O01 GoToChge: " - ", the robot continues working normally.
O01 GoToChge: " √ ", the robot returns to its charging station
immediately.
4•9•3 OPTION "O02 - STAY@CHGE"
This option forces the robot to return to its charging station and stay
there until further instruction from the user.
From the "MENU" screen, press F2.
O02 Stay@Chge: " - ", the robot continues working normally.
O02 Stay@Chge: " √ ", the robot returns to its station immediately
and stays there.
To restart the recharged robot, open the access hood, press F2 - # -
ON and close the hood again within 8 seconds.
4•9•4 OPTION "O03 - DEMOMODE"
The demo mode allows the user to start up the robot, with or
without a boundary signal. The cutting heads will not be activated
in this mode: the robot will move around without mowing.
From the "OPTIONS" screen, press # - 3 and use the # key to select
or deselect the option.
O03 DemoMode: " - ", the robot works as normal, with a
boundary signal.
O03 DemoMode: " √ ", the robot moves without mowing,
with or without a boundary signal.
4•9•5 OPTION "O04 - NOCHGEBIP"
When the robot is charging, it beeps twice every 10 seconds to show
that it is still connected to its station. However, it can be set to silent
mode if the station is located near a dwelling, patio etc.
From the "OPTIONS" screen, press # - 4 and use the # key to
select or deselect the option.
O04 NoChgeBip: " - ", the robot beeps twice every 10 seconds
while its batteries are charging.
O04 NoChgeBip: " √ ", the robot stays silent while its batteries
are charging.
Advertisement
Table of Contents
