Table of Contents
Advertisement
4•3•2 MODIFICATION OF THE CUTTING
HEIGHT
PROCESS
MEANINGS
1.
Open the cover (picture 7a)
2.
Lift the selection needle (picture 7b)
3.
Slide the selection bar to the desired height
(picture 7c)
4.
Drop the needle
5.
Close the cover
4•4 USE OF THE ROBOT MOWER
ETM105: CHARGING
The robot mower ETM105 is configured in the factory with the
standard parameters. When the terrain presents some peculiarities,
it is advised that you ask your dealer to configure the robot mower
ETM105 for your application.
When the peripheral wire (see "setting up the peripheral wire")
and the charging station (see "setting up the charging station")
are connected correctly, you can start operating your robot mower
ETM105.
4•4•1 CHARGE OF THE BATTERY
For safety reasons, the robot mower ETM105 is supplied with an
uncharged (or slightly charged) battery. During its first use, the
robot mower ETM105 must therefore be placed on its station for a
first battery charge (manual charge) (see picture 8). This may take
approximately 1:30 hour. Afterwards, it will need approximately
1:10 hour of charging for 1:40 hour of operation. But be careful,
this may vary depending on the temperature or workload on the
cutting motors.
In continuous operation mode, when its charge level is too low, the
robot mower ETM105 automatically goes to recharge itself. When
the battery is charged, it starts a cycle again (one mowing cycle +
one charge). If during a cycle, the resistance of the grass is low,
this means that the grass has not grown much. The robot mower
ETM105 therefore waits a few hours before starting its work again.
The robot mower ETM105 only works when necessary.
4•4•2 CHARGING
PROCESS
MEANINGS
1.
Put the switch to 1 (picture 11a)
2.
Press
of the keypad (picture 9)
Place the robot mower ETM105 on the
3.
charging station
4.
Type your code "*_ _ _ _" followed by "#"
5.
Let reload (manual charge)
6.
Once charged take the machine out manually
Press
7.
machine and close the cover
4• OPERATING INSTRUCTIONS
of the keypad to start up the
4•5 CONFIGURATION OF THE ROBOT
MOWER ETM105: KEYPAD
4•5•1 USE OF THE KEYPAD
The keypad includes 17 keys (10 numbers and 7 action keys) :
Keys
Switch on and start the robot.
Bring the robot back to the charging station. When
F1
the battery is charged, the robot will automatically
continue its mowing programme.
Navigate through the menu and sub-menus.
Bring the robot back to the charging station. The robot
F2
will remain at the station even after the battery has
been charged. The user will need to press the key
for the robot to continue its mowing programme.
Navigate through the menu and sub-menus.
Show the "magnetic distance" of the robot from the
F3
boundary wire (instead of the time). This function is
for after-sales services.
- Access menu and sub-menus.
#
- (De)select an option.
Go back in menu and sub-menus.
C
Delete the robot's alarm messages which are displayed
on the screen.
- Enter a pin number or access code to change settings.
*
- (De)select rest days.
To start up the machine, you have to press
picture 9) blinks), then close the cover again within 8 seconds. The
robot mower ETM105 will start up its cutting heads then start to
work.
FUNCTIONS
2 submenus are found in the "MENU":
- The "Settings" menu to access the user settings.
- The "Infos" menu (which is addressed to your technician) for all
information about the operation of your robot mower ETM105.
The selection of * enables the user code to be entered and the
machine to be activated for a chosen period. After this period, the
machine stops and the code has to be re-entered. Before a delayed
start, it is therefore advised that you re-enter the code. Without this
code, the machine will not operate.
Actions
(the screen (see
21
Advertisement
Table of Contents
