Table of Contents
Advertisement
Bennett Pacific eNVy Series Installation Manual
Determining the Number of Product Supply Pipes Needed
Determine the dispenser's model number from the serial tag located on side 1 inside the unit on the deck. Locate the
model number in the table below to determine the number of product pipes required.
Step 1
The dispenser will require a submerged pump and pressurized supply line for each product.
Step 2
Determine the number of product pipes required by finding the model number below. Note: The use of X
in the model number indicates a field where the entry in not important to this discussion.
Model Number
(Side 1 or Side 2)
1X11N1-XXXX
Use 1 product line plumbed to inlet position A
1X12N2-XXXX
1X21M1-XXXX
Use 1 product line plumbed to inlet position A
1X22M2-XXXX
Use 1 product line plumbed to inlet position C
1X22N1-XXXX
Use 1 product line plumbed to inlet position B
1X24N2-XXXX
Use 1 product line plumbed to inlet position C
1X22N2-XXXX
Use 1 product line plumbed to inlet position A
Use 1 product line plumbed to inlet position C
1X31B1-XXXX
Use 1 product line plumbed to inlet position A for low-grade product
1X32B2-XXXX
Use 1 product line plumbed to inlet position C for high-grade product
1X31M1-XXXX
Use 1 product line plumbed to inlet position A for low-grade product
1X32M2-XXXX
Use 1 product line plumbed to inlet position B for middle grade product
Use 1 product line plumbed to inlet position C for high-grade product
1X33N1-XXXX
Use 1 product line plumbed to inlet position A for mid-grade product
1X36N2-XXXX
Use 1 product line plumbed to inlet position B for high-grade product
Use 1 product line plumbed to inlet position D for low-grade product
1X41B1-XXXX
Use 1 product line plumbed to inlet position A for low-grade product
1X42B2-XXXX
Use 1 product line plumbed to inlet position C for high-grade product
1X42B1-XXXX
Use 1 product line plumbed to inlet position A for low grade product
1X44B2-XXXX
Use 1 product line plumbed to inlet position C for high-grade product
Use 1 product line plumbed to inlet position B non-blended product
1X42M1-XXXX
Use 1 product line plumbed to inlet position A for low-grade product
1X44M2-XXXX
Use 1 product line plumbed to inlet position B for mid-grade product
Use 1 product line plumbed to inlet position C for non-blended product
Use 1 product line plumbed to inlet position D for high-grade product
1X51B1-XXXX
Use 1 product line plumbed to inlet position A for low-grade product
1X52B2-XXXX
Use 1 product line plumbed to inlet position C for high-grade product
1X56B1-XXXX
Use 1 product line plumbed to inlet position A, for low-grade product
1X56B2-XXXX
Use 1 product line plumbed to inlet position B for non-blended product
Use 1 product line plumbed to inlet position C for alternative product
Use 1 product line plumbed to inlet position D for high grade
1X56E1-XXXX
Use 1 product line plumbed to inlet position A for low-grade and alternative product
1X56E2-XXXX
Use 1 product line plumbed to inlet position B for high-grade product
Use 1 product line plumbed to inlet position D for alternative product
1X53M1-XXXX
Use 1 product line plumbed to inlet position A, for low-grade product
1X56M2-XXXX
Use 1 product line plumbed to inlet position B for non-blended product
Use 1 product line plumbed to inlet position C for alternative product
Use 1 product line plumbed to inlet position D for high grade
Introduction
Product Supply Lines Required
6
Introduction
Chassis
(outside width)
44 ½"
44 ½"
44 ½"
44 ½"
44 ½"
44 ½"
52 5/8"
44 ½"
44 ½"
52 5/8"
44 ½"
52 5/8"
52 5/8"
52 5/8"
Advertisement
Table of Contents
