AUMA SA Series Operating Instructions Manual page 92

Spare parts
Please state device type and our order number (see name plate) when ordering spare parts. Only original AUMA spare parts should be used.
Failure to use original spare parts voids the warranty and exempts AUMA from any liability. Representation of spare parts may slightly vary
from actual delivery.
Ref. no. Designation
001.0 Housing
002.0 Bearing flange
003.0 Hollow shaft
005.0 Drive shaft
005.1 Motor coupling
005.3 Manual drive coupling
006.0 Worm wheel
009.0 Manual gearing
017.0 Torque lever
018.0 Gear segment
019.0 Crown wheel
022.0 Drive pinion II for torque switching
023.0 Output drive wheel for limit switching
024.0 Drive wheel for limit switching
025.0 Locking plate
058.0 Cable for protective earth
070.0 Motor (only for V... motors incl. ref. no.
079.0)
079.0 Planetary gearing for motor drive (only for
V... motors)
155.0 Reduction gearing
500.0 Cover
501.0 Socket carrier (complete with sockets)
502.0 Pin carrier without pins
503.0 Socket for controls
504.0 Socket for motor
505.0 Pin for controls
506.0 Pin for motor
507.0 Cover for electrical connection
511.0 Threaded plug
514.0 Output drive type A (without stem nut)
514.1 Axial needle roller bearing
514.2 Radial seal for output drive type A
516.0 Output drive type D
516.1 Output drive shaft D
535.1 Snap ring
539.0 Screw plug
92
SA 07.2 SA 16.2 / SAR 07.2
Type Ref. no.
Sub-assembly 542.0
Sub-assembly 549.0
Sub-assembly 549.1
Sub-assembly 551.1
553.0
554.0
556.0
Sub-assembly 556.1
Sub-assembly 557.0
558.0
559.0 1
Sub-assembly 559.0 2
Sub-assembly 560.0 1
Sub-assembly 560.0 2
Sub-assembly 560.1
Sub-assembly 560.2 1
Sub-assembly 560.2 2
Sub-assembly 566.0
Sub-assembly 566.1
Sub-assembly 566.2
Sub-assembly 566.3
Sub-assembly 567.1
Sub-assembly 568.1
Sub-assembly 568.2
Sub-assembly 568.3
Sub-assembly 568.4
Sub-assembly 575.1
Sub-assembly 583.0
Sub-assembly 583.1
Sub-assembly 584.0
614.0
Sub-assembly 627.0
S1
S2
Sub-assembly
SAR 16.2 Control unit: electronic (MWG)
AC 01.2 Non-Intrusive EtherNet/IP
Designation
Handwheel with ball handle
Output drive types B/B1/B2/B3/B4/C/E
Output drive sleeve B/B1/B2/B3/B4/C/E
Parallel key
Mechanical position indicator
Socket carrier for motor plug/socket con-
nector with cable harness
Potentiometer as position transmitter
Potentiometer without slip clutch
Heater
Blinker transmitter including pins at wires
(without impulse disc and insulation plate)
Electromechanical control unit with
switches, including torque switching heads
Electronic control unit with magnetic limit
and torque transmitter (MWG)
Switch stack for direction OPEN
Switch stack for direction CLOSE
Switch for limit/torque
Switch case for direction OPEN
Switch case for direction CLOSE
RWG position transmitter
Potentiometer for RWG without slip clutch
Position transmitter board for RWG
Cable set for RWG
Slip clutch for potentiometer
Stem protection tube (without cap)
Protective cap for stem protection tube
V-seal
Threaded sleeve
Stem nut A (without thread)
Motor coupling on motor shaft
Pin for motor coupling
Retaining spring for motor coupling
EWG position transmitter
MWG 05.03 cover
Seal kit, small
Seal kit, large
Type
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Sub-assembly
Set
Set