Grundfos CIM 200 Functional Profile And User Manual page 56

Code Description
Electronic inverter protection
106
activated (EIP)
107 -
108 -
109 -
110 Skew load, electrical asymmetry
111 Current asymmetry
112 Cosφ too high
113 Cosφ too low
Motor heater function activated
114
(frost protection)
Too many grinder reversals or
115
grinder reversal attempt failed
116 Grinder motor overtemperature
117 Intrusion (door opened)
Signal fault, hydrogen sulfide H2S
118
sensor
119 Signal fault, analog input AI4
Auxiliary winding fault (single
120
phase motors)
Auxiliary winding current too high
121
(single-phase motors)
Auxiliary winding current too low
122
(single-phase motors)
Start capacitor, low (single-phase
123
motors)
Run capacitor, low (single-phase
124
motors)
Signal fault, outdoor temperature
125
sensor
Signal fault, air temperature
126
sensor
Signal fault, shunt relative
127
pressure sensor
128 Strainer clogged
129 -
130 -
131 -
132 -
133 -
134 -
135 -
136 -
137 -
138 -
139 -
140 -
56
Code Description
141 -
142 -
143 -
Motor temperature 3 (Pt100,
144
t_mo3)
Bearing temperature high (Pt100),
145
in general or top bearing
Bearing temperature high (Pt100),
146
middle bearing
Bearing temperature high (Pt100),
147
bottom bearing
Motor bearing temperature high
148
(Pt100) in drive end (DE)
Motor bearing temperature high
149
(Pt100) in non-drive end (NDE)
150 Fault (add-on) pump module
151 Fault, display (HMI)
Communication fault, add-on
152
module
153 Fault, analog output
154 Communication fault, display
155 Inrush fault
Communication fault, internal
156
frequency converter module
157 Real-time clock out of order
Hardware circuit measurement
158
fault
CIM fault (Communication
159
Interface Module)
160 Cellular modem, SIM card fault
161 Sensor supply fault, 5 V
162 Sensor supply fault, 24 V
Measurement fault, motor
163
protection
164 Signal fault, LiqTec sensor
165 Signal fault, analog input 1
166 Signal fault, analog input 2
167 Signal fault, analog input 3
168 Signal fault, pressure sensor
169 Signal fault, flow sensor
Signal fault, water-in-oil (WIO)
170
sensor
171 Signal fault, moisture sensor
Signal fault, atmospheric pressure
172
sensor
Signal fault, rotor position sensor
173
(Hall sensor)
174 Signal fault, rotor origo sensor
Signal fault, temperature sensor 2
175
(t_mo2)
Code Description
Signal fault, temperature sensor 3
176
(t_mo3)
177 Signal fault, Smart trim gap sensor
178 Signal fault, vibration sensor
Signal fault, bearing temperature
179 sensor (Pt100), general or top
bearing
Signal fault, bearing temperature
180
sensor (Pt100), middle bearing
Signal fault, PTC sensor (short-
181
circuited)
Signal fault, bearing temperature
182
sensor (Pt100), bottom bearing
Signal fault, extra temperature
183
sensor
Signal fault, general-purpose
184
sensor
185 Unknown sensor type
186 Signal fault, power meter sensor
187 Signal fault, energy meter
188 Signal fault, user-defined sensor
189 Signal fault, level sensor
Limit exceeded, sensor 1 (for
190 example alarm level in WW
application)
Limit exceeded, sensor 2 (for
191 example high level in WW
application)
Limit exceeded, sensor 3 (for
192 example overflow level in WW
application)
Limit exceeded, sensor 4 (for
193 example low level in WW/tank
filling application)
194 Limit exceeded, sensor 5
195 Limit exceeded, sensor 6
196 Operation with reduced efficiency
197 Operation with reduced pressure
Operation with increased power
198
consumption
Process out of range (monitoring,
199
estimation, calculation, control)
200 Application alarm
201 External sensor input high
202 External sensor input low
203 Alarm on all pumps
204 Inconsistency between sensors
Level float switch sequence
205
inconsistency
206 Water shortage, level 1
207 Water leakage
208 Cavitation
209 Non-return valve fault
210 High pressure