Yamaha OWNER'S MANUAL HTR-6130 Owner's Manual page 51

Sp k di """ ""' """"'-'"''"'-
• ea er stance ,.....,.::,r.. L.,._..:, _..._.._,...._:::.
Use this feature to manually adjust the distance of each
speaker and the delay applied to the respective channel.
Ideally, each speaker should be the same distance from the
main listening position. However, this is not possible in
most home situations. Thus, a certain amount of delay
must be applied to the sound from each speaker so that all
sounds will arrive at the listening position at the same
time.
Unit UH][T
Choices: meters (m), feet (ft)
Initial setting:
[U.S.A. and Canada models]: feet (ft)
[Other models]: meters (m)
• Select "meters" to adjust speaker distances in meters.
• Select "feet" to adjust speaker distances in feet.
Speaker distances
Control range: 0.30 to 24.00 m (1.0 to 80.0 ft)
Control step: 0.10 m (0.5 ft)
Initial setting:
FRONT L/FRONT R/SWFR: 3.00 m (10.0 ft)
CENTER: 2.60 m (8.5 ft)
SUR. L/SUR. R: 2.40 m (8.0 ft)
{:::P.(){".{T L. Frontleft speaker
{:::P.(.){".{T{:;?. Front right speaker
(.i: [ :il{".{ 'r [:il { :4: Center speaker
'.iii;U{:;?. = L.
Surroundleft
speaker
.::a..u',:. == !',:. Surround right speaker
'.::@ 1... 1.,:'. Subwoofer
Press @A / V to select a frequency band and @<:1 / 1::>to adjust
the selected frequency band.
Followingisan example where"100Hz"isselected asthe
frequency band.
Test tone 'fE:iii;T
Use this feature to make adjustments for "CENTER GEQ"
while listening to a test tone.
Choices: OFF, ON
• Select "OFF" to stop test tones and output the currently
selected source component.
• Select "ON" to output test tones from the center and
front left speakers.
• Low-frequency effect level
:.,... : :.,..:-.. : :.,..: ::.,..:
i... ii i...i.., i i...i ii...i
I.=,= . ) l.ml I.=,= l.m I.=,= "=' l.m I
Use this feature to adjust the output level of the LFE
(low-frequency effect) channel according to the capacity
of your subwoofer or headphones. The LFE channel
carries low-frequency special effects which are only added
to certain scenes. This setting is effective when the input
signal contains the LFE channel.
Control range: -20 to 0 dB
Control step: 1 dB
Speaker LFE :iii;i:::' L,i:::i ....
Adjusts the speaker LFE level.
Headphone LFE iii:::' L ,i:::iii]
Adjusts the headphone LFE level.
The available speaker channels differ depending
on the setting
of
the speakers.
• Center graphic equalizer i:;:,::,_:;;:iiii;i..iiiiii;i:.:i: (.iiiiii;(;!
Use this feature to adjust the built-in 5-frequency band
(100Hz, 300Hz, lkHz, 3kHz and 10kHz) graphic
equalizer for the center channel so that the tonal quality of
the center speaker matches that of the front speakers. You
can make adjustments while listening to the currently
selected source component or a test tone.
Control range: -6.0 to +6.0 dB
Control step: 0.5 dB
Initial setting: 0 dB
Depending on the settings of "BASS OUT" (see page 46), some
signals may not be output at the SUBWOOFER OUTPUT jack.
• Dynamic range i:::::,i]:,,, i::i:!:::!i..iGii:.i;
Use this feature to select the amount of dynamic range
compression to be applied to your speakers or
headphones. This setting is effective only when this unit is
decoding Dolby Digital and DTS signals.
Choices: MIN, STD, MAX
• Select "MIN" (minimum) if you regularly listen at low
volume levels.
• Select"STD" (standard) for general use.
• Select "MAX" (maximum) to preserve the greatest
amount of dynamic range.
Speaker dynamic range :iii;i:::' i),, i;:
Adjusts the speaker compression.
Headphone dynamic range i...ii:::' i),, i:,i:
Adjusts the headphone compression.
47
En