Table of Contents
Advertisement
36
model no. 055-6755-8 | contact us 1-800-689-9928
INSTALL THE RIGHT EXTENSION TABLE
(Fig. 8)
•
Align the holes on the right extension table (1) with the
holes on the work table.
•
Insert the hex bolts M6 x 12 (2) into spring washers 6
(3), flat washers 6 (4) and holes.
•
Tighten the hex bolts M6 x 12 (2).
Make sure that only one hole (5) on the side of the right
extension table is in the front when finished.
ASSEMBLE THE FRONT RAIL (Fig. 9a-9c)
•
Push the four hex bolts M6 x 12 (1) onto the slot of the
front rail (2) from the side of the front rail one at a time.
•
Insert the hex bolts M6 x 12 (1) through the holes on
the work table and right extension table, then put on
the flat washers 6 (3) and spring washers 6 (4) and
loosely tighten the hex nuts M6 (5) as shown in the
Fig. 9b.
•
Carefully place the rip fence (6) into the channel of the
front rail (2) and push the rip fence (6) completely
against the saw blade (7) and hold firmly.
•
Move the front rail (2) in such a way that the red line
marking on the guide pointer (8) is in the zero position
on the scale.
•
Tighten all the hex nuts M6.
1
3
5
4 2
Fig. 8
2
1
2
1
Fig. 9a
1
2
5 3
4
Fig. 9b
7
6
8
2
Fig. 9c
REMOVE AND INSTALL THE BLADE (Fig. 10)
CAUTION:
To work properly, the saw blade teeth must point down toward the front of the saw. Failure to heed
this instruction could cause damage to the saw blade, the saw or the workpiece.
WARNING!
Make sure that the saw blade is installed to rotate in the proper direction. Do not use grinding
wheels, wire brushes, or abrasive wheels on a table saw. Improper saw blade installation or use of
accessories not recommended may cause serious injury.
WARNING!
Only use a 10" (25.4 cm) diameter blade. To avoid injury from an accidental start, make sure the
switch is in the OFF position.
•
Turn saw off and unplug saw.
•
Lower the saw blade and remove the table insert.
•
Make sure the bevel locking lever is securely locked.
Turn the height-adjusting knob clockwise to raise
blade to maximum height.
•
Place riving knife in the uppermost position.
•
Remove the blade wrenches from storage area.
Remove the blade:
•
Remove the table insert.
•
Set the saw blade angle to 0°.
•
Using one opened-ended blade wrench (1), place the
flat open end on the flats on the outer blade flange (2).
•
Using the other opened-ended blade wrench (3), place the flat open end on the flats on the arbour nut (4).
•
Holding both wrenches firmly, pull the opened-ended blade wrench on the arbour nut forward to the front
of the machine.
•
Remove arbour nut (4), outer blade flange (2) and saw blade (5).
WARNING!
Be extremely careful when loosening arbour nut. Keep firm grasp on both wrenches. Do not allow
hands to slip and contact blade.
Install the blade:
•
Place one new blade on arbour (6). Make sure saw blade teeth point down at the front side of saw table.
Place outer blade flange (2) and arbour nut (4) on arbour (6) and use blade wrenches to tighten arbour
nut securely. DO NOT over tighten.
WARNING!
If the inner blade flange has been removed, reinstall it before placing the saw blade on arbour.
Failure to do so could cause an accident.
6
7
1
2
4
5
3
Fig. 10
37
Hide quick links:
Advertisement
Table of Contents
