Download Print this page
MasterCraft 055-6778-4 Instruction Manual

MasterCraft 055-6778-4 Instruction Manual

Tabletop wet tile saw with extension table

Advertisement

model no. 055-6778-4
bs
IMPORTANT:
Please read this manual carefully before using this tile
saw with extension table and save it for reference.
TABLETOP
WET TILE SAW WITH

EXTENSION TABLE

INSTRUCTION
MANUAL

Advertisement

loading
Need help?

Need help?

Do you have a question about the 055-6778-4 and is the answer not in the manual?

Questions and answers

Art chatten
February 5, 2025

My rip knife broke on my guard, its number 49 on the parts diagram but there is no part number i need to order a new one

Summary of Contents for MasterCraft 055-6778-4

  • Page 1: Extension Table

    055-6778-4 TABLETOP WET TILE SAW WITH EXTENSION TABLE IMPORTANT: INSTRUCTION Please read this manual carefully before using this tile MANUAL saw with extension table and save it for reference.
  • Page 2: Table Of Contents

    TABLE OF CONTENTS Quick Start Guide Specifications Safety Guidelines 6-12 Know Your Tile Saw 13-14 Assembly Instructions 15-22 Operating Instructions 23-27 Maintenance 28-29 Troubleshooting Exploded View Parts List 32-33 Warranty NOTE: If any parts are missing or damaged, or if you have any questions, please call our toll-free helpline at: 1-800-689-9928 SAVE THESE INSTRUCTIONS This manual contains important safety and operating instructions.
  • Page 3: Specifications

    055-6778-4 | contact us 1-800-689-9928 SPECIFICATIONS • Locate hole on bottom of water fill reservoir. Motor 120V, 60 Hz, 5.0A • Push water reservoir plug (1) into hole Speed 5300 RPM (no load) firmly. Table tilts 0°,15°, 30° & 45°...
  • Page 4: Safety Guidelines

    055-6778-4 | contact us 1-800-689-9928 SAFETY GUIDELINES • MAKE WORKSHOP CHILDPROOF with padlocks, master switches or by removing starter keys. • DON'T FORCE TOOL. It will do the job better and safer at the rate for which it was designed.
  • Page 5 055-6778-4 | contact us 1-800-689-9928 • Replace table insert when worn. be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other •...
  • Page 6 055-6778-4 | contact us 1-800-689-9928 USE SAFETY GOGGLES AND EAR PROTECTION: Do not modify the plug provided. If it will not fit the outlet, have the proper outlet installed by a qualified electrician. ALWAYS WEAR EYE PROTECTION THAT CONFORMS WITH CUL REQUIREMENTS. FLYING DEBRIS can cause permanent eye damage.
  • Page 7 055-6778-4 | contact us 1-800-689-9928 Recommended size for extension cords AMPERAGE RATING OF THE TOOL TOTAL LENGTH OF THE EXTENSION CORD (120 V CIRCUIT ONLY) 25' (7.6 m) 50' (15.2 m) 100' (30.5 m) 150' (45.7 m) MORE THAN...
  • Page 8 055-6778-4 | contact us 1-800-689-9928 On/Off switch: PACKAGE CONTENTS This saw has an easy-access power switch located below the front rail. To lock the switch in the Off position, Description Qty. Illustration remove the switch key from the switch. Place the key in a location that is inaccessible to children and others not qualified to use the tool.
  • Page 9 055-6778-4 | contact us 1-800-689-9928 FITTING THE CUTTING DISC (Fig. 1-4) Description Qty. Illustration • Unplug the tile cutter from the mains supply. • Raise the 45° Vertical fence (1) approx. 45° and Wrenches remove. • Loosen cross-screws (2) with the Star-head screwdriver (not supplied) and pull off lower protective guard (3).
  • Page 10 055-6778-4 | contact us 1-800-689-9928 ASSEMBLE/ADJUST THE METAL BRACKET (Fig. 5) MOUNTING THE EXTENSION TABLE (Fig. 8-10) • Loosen two cross-screws (1) with the Star-head • Undo the cross-screws (1) on the guide rails of the screwdriver (not supplied).
  • Page 11 055-6778-4 | contact us 1-800-689-9928 MOUNTING THE PARALLEL CUTTING GUIDE (Fig. 11) INSTALLING THE MITRE CUTTING GUIDE (Fig. 12) • Attach the rear end of the parallel cutting guide (1) to the rear of the working table. • Slide mitre cutting guide (1) onto parallel cutting guide (2) from front.
  • Page 12 055-6778-4 | contact us 1-800-689-9928 FILLING THE WATER RESERVOIR (Fig. 14) CHECK BEFORE STARTING! • Raise the 45° vertical fence approx. 45° and remove. • The product must be mounted on a stable surface, i.e. on a workbench.
  • Page 13 055-6778-4 | contact us 1-800-689-9928 ON/OFF SWITCH (Fig. 15) TO MAKE A CROSS CUT (Fig. 17) • To turn the tile saw On, insert the safety key (1) into the • Cross cuts are straight 90° cuts. The material is fed into switch housing.
  • Page 14 055-6778-4 | contact us 1-800-689-9928 TO MAKE A MITRE CUT (Fig. 19) angle. Mitre cuts are used for cutting outside and inside corners on • Turn the On/Off switch to the ON position. material, decorative chair rails and base moldings with the •...
  • Page 15 055-6778-4 | contact us 1-800-689-9928 GENERAL MAINTENANCE • Raise the 45° vertical fence (1) approx. 45° and remove. (Fig. 22) Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, •...
  • Page 16: Troubleshooting

    055-6778-4 | contact us 1-800-689-9928 TROUBLESHOOTING PROBLEM Possible Causes Solution Motor not running. No mains voltage. Check cable, plug, socket and fuse. Motor runs, cutting disc Flange nut loose. Check that the flange is seated 46 30 remains still.
  • Page 17: Parts List

    055-6778-4 | contact us 1-800-689-9928 PARTS LIST Description Description Water reservoir plug Wrench (A) Description Description O-ring Self-locking switch box Bolt ST3.9×12 rip fence spring Waterproof pad Wrench (B) Self-locking switch Rip fence Press block Cushion Cord outlet...
  • Page 18: Warranty

    055-6778-4 | contact us 1-800-689-9928 3-Year Limited Warranty This Mastercraft product is guaranteed for a period of 3 years from the date of original retail purchase against defects in workmanship and materials, except for the following component: Component A: Accessories, which are guaranteed for a period of 1-year from the date of original retail purchase against defects in workmanship and materials.