Table of Contents
Advertisement
Item
Qty.
1
Pump Module (complete), 12 Volt, Rear
1
1
Pump Assembly (M268BP with Reservoir/with Backup pump - Non Bridging)
2
1
Fitting, 7/16"-20 O-Ring Male / 7/16"-20 JIC 37° Male
3
1
Elbow, 7/16"-20 JIC 37° Female Swivel (1) / 7/16"-20 JIC 37° Male (2)
4
1
Switch, Pressure
5
1
Clamp, Hose
See Control Box Assembly and Harness Options ✘ See note below
6
1
See Control Box Assembly and Harness Options ✘ See note below
7
1
Control Box, Bracket-mount (Items 9, 10 and 11) ✘ See note below
8
1
Control Box (only) ✘ See note below
9
1
Clip, Bracket-mount ✘ See note below
10
1
Screw, #6-20 x 1-1/4", Pan Head, Phillips ✘ See note below
11
3
Face Plate and Switch Assembly ✘ See note below
12
1
Face Plate ✘ See note below
13
1
Switch, S.P.D.T., Rocker (Unfold/Fold) - Orange ✘ See note below
14
1
Switch, S.P.D.T., Rocker (Down/Up) - Red ✘ See note below
15
1
Screw, #6-20 x 3/4", Pan Head, Phillips ✘ See note below
16
4
Strain Relief (SR 7W-2) ✘ See note below (7A, 7B and 7C only)
17
1
Cover, Switch Box ✘ See note below
18
1
19
1
Lead Wire Assembly, #6 Gauge Red
20
1
Solenoid, 4 Post
21
1
Harness, Up/Fold and Unfold/Down
22
1
Cable, Pump Module Power Feed, #4 Gauge Red
23
1
Harness, Up Solenoid / Circuit Breaker
24
1
Circuit Breaker, 5 Amp, Manual Reset
25
1
Harness, Power / Ground
26
1
Harness, Pendant Control Cable
27
1
Harness, Main
28
1
Jumper, Interlock
29
1
Jumper, Positive or Negative Logic - Vista
30
1
Circuit Board, Seat Belt Interlock
31
4
Standoff, 1/4" Long, Printed Circuit Board
32
4
Screw, #6 x 3/8", Self Tap, Flat Head
33
4
Snap Rivet, 1/8", Nylon, Black
34
1
Stud, Power Feed
Cable, Lift Power, 37' with Loom ✘ See note below
35
1
Rubber Boot, Red ✘ See note below
36
1
37
1
Plate, Backing / Mounting, Rear
38
2
Washer, 5/16" Flat
Cable, Ground - 36" ✘ See note below
39
1
40
4
Bolt, 5/16"-18 x 1/2", Nylock, Hex * See note below
41
1
Diode Assembly, Up Solenoid
Control Box Assembly and Harness Options
Item
Qty.
Control Box Assembly (with Standard Quick Disconnect Harness) ✘ See Note Below
6A
1
Control Box Assembly (with Armored Quick Disconnect Harness) ✘ See Note Below
6B
1
Control Box Assembly (with Coiled Quick Disconnect Harness) ✘ See Note Below
6C
1
Control Box Assembly (with 7' Long, 18 Ga., Quick Disconnect Harness) ✘ See Note Below (not shown)
6D
1
Harness, Standard, Quick Disconnect (without control box) ✘ See Note Below
7A
1
Harness, Armored, Quick Disconnect (without control box) ✘ See Note Below
7B
1
Harness, Coiled, Quick Disconnect (without control box) ✘ See Note Below
7C
1
Harness, 7' Long, 18 Ga., Quick Disconnect (without control box) ✘ See Note Below (not shown)
7D
1
✘ Indicates items available for replacement part purposes only. These items are not included with replacement pump
modules.
* Apply red #271 Thread Locker Loctite
on the bolts when retrofitting an M268 pump assembly. Loctite
number 11522.
Page 54
Rear
Pump Module
Description
Description
®
to the three pump mounting bolts (item 39) if a blue nylon patch is not present
Parts List
Part No.
®
is available from The Braun Corporation under part
Part No.
975R0516IBQD
28493A12V
24504
26579
26577
17069
16970A
16932
16933
16945
17909A-05
16931-05
17332
16942
24739
11352
26798
29049
28308
975-0533A
26082A-4
25809A
25736
975-0530A
975-0531A
975-0532A
15708A
29247
28776
86739
82764
25759
26084
205-0712-37
82046
975R0501MT
10063
26161A
10012
73906A
Part No.
900-0903AQD
900-0903AQDA
900-0903AQDC
900-5903AQD
900-0902AQD
900-0902AQDA
900-0902AQDC
900-5902AQD
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
