Summary of Contents for Braun NCL Century 2 Series
Page 1
Service Manual for: Century Series Public Use Wheelchair Lifts Series DOT — Public Use Lift DOT — Public Use Lift “DOT — Public Use Lift” verifies that this platform lift meets the “public use lift” requirements of FMVSS No. 403. This lift may be installed on all vehicles appropriate for the size and weight of the lift, but must be installed on buses, school buses, and multi- purpose passenger vehicles other than motor homes with a gross...
Page 2
The warranty cards must be processed to activate the warranty. Two Braun Serial No./Series No. identification tags (shown below) are posted on the lift. One I.D. tag is posted on the opposite pump side vertical arm. A second I.D. tag is located on the opposite pump side tower.
Page 7
Platform Fold Pressure Adjustment pressed. platform. Do not adjust this valve. (located beside solenoid valves) Platform Fold screw and tighten hex Page 5...
Page 8
Platform Angle Adjustment Figure A Barrier Heel Platform heel The angle of the platform at the angle of the platform when platform. Figure B Floor Wedges (option) Adjustment Procedure: of the platform (see photo at right When and details on following page). Vertical Stop arms (see photo at right and...
Page 9
Platform Angle Adjustment ® to lower end of platform to raise end of platform Platform Stop Blocks Right Wrong Gap not permitted. Stop Block Guideline All Lift Models Vertical Stop Vertical Stop Page 7...
Page 10
Tower Microswitch Adjustment TOWER TOWER TOWER TOWER 32943 32942 Figure B TOWER TOWER TOWER TOWER 32943 32942 lift is a mirrored image. as needed only. Tower 1 (Unfold) Switch Adjustment Tower 3 (Alarm) Switch Adjustment Floor Position from Stow dant control. Tower 4 (Fold) Switch Adjustment Partial Fold Switch of the saddle and the lower parallel...
Page 12
Maintenance and Lubrication Lubrication Diagram Lift-Tite ™ (2 springs - 4 Points) LO Lift-Tite ™ Latches Saddle Bearing (2) Bearings (4) Roller Pin Bearings (4) Inner Roll Stop Bearings (8) and Slots (2) Inner Roll Stop Cam Followers (4) Bearings (8) Lift-Tite ™...
Page 13
Maintenance and Lubrication Schedule W ARNING Maintenance and lubrication procedures must be performed as 4500 cycle maintenance authorized service technician. Failure to do so may result in serious bodily injury and/or property damage. life of the lift. Cycle Counter: NCL-2 Series lift models are to the components.
Page 14
Maintenance and Lubrication Schedule spring(s) Cycles Correct as needed. condition Correct as needed. Inspect lift for rattles Perform all procedures listed in previous section also Inner fold arm cam followers (4) 1500 Cycles Inspect Lift-Tite ™ Inspect inner roll stop for: Replace damaged parts.
Page 15
Maintenance and Lubrication Schedule Inspect external snap rings: ™ latch rollers (2) ™ latch gas (dampening) springs (4) 1500 Cycles Perform all procedures listed in previous section also ® Replace if needed. 4500 Cycles Tighten or replace if needed. Replace if needed. Inspect gas springs (cylinders - 6) for wear or dam- Page 13...
Page 21
Hydraulics Diagram Hydraulic Repair For repair of a hydraulic hose or cylinder, read this. Service Hydraulic Bulletin 27049 Pump Motor Manual Backup Pump Page 19...
Page 23
Pump Module Diagram Pump Mounting Bolts Apply Loctite ® Threadlocker Red 271™ or equivalant to the three pump mount- ing bolts (items 25 and 26) if a blue nylon patch is not present on the bolts sembly. Note: Rear pump module shown, front pump module mirror image.
Page 24
Exploded Views and Parts Lists NCL917IB-2 Base Plate Assembly DWG. NOTES 1) LOOP TAPESWITCH WIRE BACK AND SECURE WITH WIRE TIE 4X. 2) TRIM AND TUCK WIRE TIE CLASP INTO HOLE 4X. 3) APPLY LOCTITE ® THREADLOCKER RED 271™ OR EQUIVALANT TO ALL #25527 SCREWS. NOTE: "A"...
Page 25
Exploded Views and Parts Lists NCL917FIB-2 Base Plate Assembly DWG. NOTES 1) LOOP TAPESWITCH WIRE BACK AND SECURE WITH WIRE TIE 4X. 2) TRIM AND TUCK WIRE TIE CLASP INTO HOLE 4X. 3) APPLY LOCTITE ® THREADLOCKER RED 271™ OR EQUIVALANT TO ALL #25527 SCREWS. NOTE: "A"...
Page 26
Exploded Views and Parts Lists NCL919IB-2 Base Plate Assembly DWG. NOTES 1) LOOP TAPESWITCH WIRE BACK AND SECURE WITH WIRE TIE 4X. 2) TRIM AND TUCK WIRE TIE CLASP INTO HOLE 4X. 3) APPLY LOCTITE ® THREADLOCKER RED 271™ OR EQUIVALANT TO ALL #25527 SCREWS. NOTE: "A"...
Page 27
Exploded Views and Parts Lists NCL919FIB-2 Base Plate Assembly DWG. NOTES 1) LOOP TAPESWITCH WIRE BACK AND SECURE WITH WIRE TIE 4X. 2) TRIM AND TUCK WIRE TIE CLASP INTO HOLE 4X. 3) APPLY LOCTITE ® THREADLOCKER RED 271™ OR EQUIVALANT TO ALL #25527 SCREWS. NOTE: "A"...
Page 28
Exploded Views and Parts Lists Top Parallel Arm Assembly - Front ITEM QTY. PART NO. DESCRIPTION 10058 NUT-5/16-18 HEX/AUTO-BK 10068 WASHER-5/16" LOCK/AUTO-BK 15858BK BOLT-CARR 5/16-18 X 3/4/AUTO-BK 16368 WASHER-5/16" EXTERNAL TOOTH 24440 BOLT-5/16-18 X 3/4-BHSC/AUTO-BK 28593A ASSY-BLOCK-GUIDE-PLATFORM-STOW 955-2392CLXT BKT.-QUIET-RIDE MTG.-955 14993 RIV-POP-SD66BS-3/16"-.25/.38/AUTO-BK 915-0703...
Page 29
Exploded Views and Parts Lists Bottom Parallel Arm Assembly - Rear PART NO. DESCRIPTION ITEM QTY. 18349 NUT-#10-32 W/LOCKWASHER/AUTO-BK 32514NA ASSY-IB OCCUPIED 34398 WASHER-0.906"ID X 1.25"OD X .075"TH/ZINC 24011 BEARING-FLANGE-3/4" X 3/8"-12FDU06 945-3458NKS ARM-PARALLEL/BOTTOM-SWITCH (Incl. Items 1-3) Bottom Parallel Arm Assembly - Front ITEM QTY.
Page 30
Exploded Views and Parts Lists Hydraulic Cylinder Assembly - Main RETRACTED 29.146 STROKE 14.625 EXTENDED 43.771 30° ±10° PART NO. DESCRIPTION ITEM QTY. 15150 ELBOW-1/4 NPT 90° 1/4 BARB 26667 ELBOW-7/16-20 M/O-RNG/37*/.035 ORFICE C1514.3-0408N CYLINDER-14.625"/29.146 RETRACTED Page 28...
Page 31
Exploded Views and Parts Lists Vertical Arm Assembly - Rear DWG. NOTES 1) INSERT SOCKET OF LIGHT ASSY THRU TOP KEY WHILE INSTALLING LIGHT. TIGHTEN SCREWS. NOTE: 1 2) HARNESS TO BE TUCKED INSIDE CHANNEL. 3) APPLY LOCTITE ® THREADLOCKER BLUE 242 ®...
Page 32
Exploded Views and Parts Lists Front Handrail Assembly ITEM QTY. PART NO. DESCRIPTION 25171 BOLT-3/8-16 X 3/4" FLBHSCS-GD8 10069 WASHER-3/8" LOCK 11513 RIV-POP-SD64BS-3/16"-.13/.25/AUTO-BK 29185 BALL STUD-13MM W/ 3/8-16 FEMALE THREAD 29186 GAS SPRING-14.468 EXT/8.956 COM-P1=1150N 30227 SPACER-UHMW 0.75 OD X 0.39 ID X 0.25 13617 NUT-3/8-16 UNC HEX LOCK/AUTO-BK 945-0640FNA...
Page 33
Exploded Views and Parts Lists NCL917IB-2 & NCL917FIB-2 Platform Assembly DWG. NOTES 1) USE LOCTITE ® THREADLOCKER RED 271™ OR EQUIVALENT ON SCREWS (B.C. #24537 AND B.C. 15733 2) USE LOCTITE ® THREADLOCKER GREEN 290™ OR EQUIVALENT ON CLEVIS PINS (B.C. #24932BK) 3) APPLY BOUNDARY DECAL (ITEM 33) 48 1/8"...
Page 34
Exploded Views and Parts Lists NCL919IB-2 & NCL919FIB-2 Platform Assembly DWG. NOTES 1) USE LOCTITE ® THREADLOCKER RED 271™ OR EQUIVALENT ON SCREWS (B.C. #24537 AND B.C. 15733 2) USE LOCTITE ® THREADLOCKER GREEN 290™ OR EQUIVALENT ON CLEVIS PINS (B.C. #24932BK) 3) APPLY BOUNDARY DECAL (ITEM 33) 48 1/8"...
Page 35
10,000 cycles and the cost of labor to repair or replace those parts for one (1) year or 3,000 cycles. If The Braun Corporation receives the warranty registration card within 20 days after the lift is put into service, the warranty labor coverage will increase from one (1) year or 3,000 cycles to three (3) years or 10,000 cycles.
Page 36
(30) days for repairs to be com- pleted, you must, to the extent permitted by law, notify Braun directly, in writing, at the above address, of the unsuccessful repair(s) of the alleged defect(s) so that Braun can become directly involved in providing service pursuant to the terms of this limited warranty.
Page 37
Braun will do and does not guarantee anything about the product for any time period. Nothing in this warranty, or any action of Braun, or any agent of Braun, shall be interpreted as an extension in the statute of limitations, so this reduction may not apply to you.
Page 38
NOTES This page intentionally left blank. Page 36...
Page 39
"Providing Access to the World" ® Over 300 Braun Dealers Worldwide ® "Providing Access to the World" International Corporate Hdqrs: P .O. Box 310 Winamac, IN 46996 USA 1-800-THE LIFT ® (574) 946-6153 FAX: (574) 946-4670...
Page 40
All illustrations, descriptions and specifications in this manual are based on the latest product information available at the time of publication. The Braun Corporation reserves the right to make changes at any time without notice. at the time of publication. The Braun Corporation reserves the right to make changes at any time without notice.
Need help?
Do you have a question about the NCL Century 2 Series and is the answer not in the manual?
Questions and answers
What type of Hydraulic oil should i use
The recommended hydraulic oil for the Braun NCL Century 2 Series is Braun 32840-QT (Exxon® Univis HVI 26).
This answer is automatically generated