Table of Contents
Advertisement
Installation/Service Manual
Series
Millennium Series
Commercial Wheelchair Lifts
Including models:
Including models:
• 915
•L915
• 915
•L915F
• 916
•L916
• 916
•L916F
• 917
•L917
• 917
•L917F
• 918
•L918
• 918
•L918F
• 919
•L919
• 919
•L919F
and
Special Order
Special Order
L915 Series Lift Models
"Providing Access to the World"
International Corporate Hdqrs: P.O. Box 310
1-800-THE LIFT
(574) 946-6153
Patent #5,261,779
Patent #5,261,779
Patent #5,806,632
Patent #5,806,632
Patent #6,065,924
30469
Patent #6,065,924
Patent #6,238,169
May 2004
Patent #6,238,169
07
07
TM
• 915
•L915IB
• 915
•L915FIB
• 916
•L916IB
• 916
•L916FIB
• 917
•L917IB
• 917
•L917FIB
• 918
•L918IB
• 918
•L918FIB
• 919
•L919IB
• 919
•L919FIB
®
®
Winamac, IN 46996 USA
FAX: (574) 946-4670
Patent #6,464,447
Patent #6,464,447
Patent #6,599,079
Patent #6,599,079
Patent #6,692,217
Patent #6,692,217
Patents Pending
Patents Pending
W ARNING
Read manual
before installing
or servicing lift.
Failure to do so
may result in
serious bodily
injury and/or
property damage.
ADA
ADA
complying with
complying with
Americans With
Americans With
Disabilities Act
Disabilities Act
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Braun 07 Series
Summary of Contents for Braun 07 Series
- Page 1 Installation/Service Manual Series Millennium Series Commercial Wheelchair Lifts Including models: Including models: • 915 • 915 •L915 •L915IB • 915 • 915 •L915F •L915FIB • 916 • 916 •L916 •L916IB • 916 • 916 •L916F •L916FIB • 917 • 917 •L917 •L917IB •...
- Page 2 Braun certified technician, and the lift is operated by an instructed person. Sincerely, THE BRAUN CORPORATION Ralph W.
-
Page 3: Table Of Contents
Contents Lift Terminology Lift Interlock Installation ..........53 Lift Electrical Schematic ..........54 Lift Wiring Diagram ............. 55 Lift Terminology Illustration ..........2 18 Gauge Lift Control Box Electrical Schematic ..56 Introduction ..............3 18 Gauge Lift Control Box Wiring Diagram ....56 Direction ................ -
Page 4: Lift Terminology Illustration
Lift Terminology Lift model numbers with suffix hinged bridge plate. Both types (front) pump lift models are a “IB” are equipped with an of bridge plates are shown in mirrored image of left side pump automatic mechanical inboard the illustration below for identifi- models (pump module located roll stop that also serves as the cation purposes (details pro-... -
Page 5: Lift Terminology
Contact your lift sales steel tubing frame with grating The L915 Millennium Lift Series representative or call The Braun surface upon which the wheelchair includes variations of lift models Corporation at 1-800-THE LIFT if... -
Page 6: Installation/Service Safety Precautions
W ARNING manual or if the area prior to beginning installation procedures. instructions are not fully understood, contact The Braun Install lift and power platform to fully folded position before W ARNING Corporation immedi- removing shipping straps. ately. Failure to do... - Page 7 Disconnect the power cable at the battery prior to servicing. W ARNING Keep hands, arms and all other body parts clear of moving parts. W ARNING Never modify (alter) a Braun Corporation lift. W ARNING Replacement parts must be Braun authorized replacements. W ARNING Never install screws or fasteners (other than factory equipped).
-
Page 8: Pre-Installation Notes
Ford Rear Door Installations: cable to your lift model. Installation Requirements: Four underfloor reinforcement Braun Bus Door Kits: Braun brackets are supplied. All four Retrofit Bus Door Kits are Braun L915 Millennium Series underfloor reinforcement brackets... - Page 9 Pre-Installation Notes There must be a minimum 1/8" Due to the “all-hydraulic” opera- Note: When mounting ground tion of the dual-cylinder L915 cables, remove undercoating, dirt, clearance between the de- ployed bridge plate assembly Series, hydraulic fluid expansion, rust, etc. from the framing mem- and any obstruction on the contraction or seepage may ber around the mounting holes...
-
Page 10: Lift Installation Instructions
Lift Installation Instructions Installation Parts Please check the Installation Parts List and Tools List to see that you have everything needed to begin. Report any missing items. Item Qty. Description Part No. Installation Parts Package (complete) Includes all following items 25853A-A4 Bracket, Underfloor, Reinforcement 25915-04... -
Page 11: Lift Mounting Hardware Illustrations
Lift Installation Instructions Ford Rear Door Figure A Installation: Four underfloor Position star washers and underfloor reinforcement mounting hardware as specified (per brackets must chassis and floor configuration). be used. Details on page 15. Through Floor Only: Position star washer Star Washers between floor and 2-1/2"... -
Page 12: Lift Positioning
Lift Installation Instructions Note: Read all Pre- Lift Positioning Installation Notes prior to installation. The lift towers (upright supports) and the vertical arms must be parallel (aligned) with the vertical sides of the door jamb and should be perpendicular (90˚) to the vehicle floor. W ARNING Install lift and power platform to fully... - Page 13 Lift Installation Instructions Clearance: Visually center the unit in the opening. Position the base plate parallel to (aligned with) the vehicle lift doorsill or stepwell as shown in Figure D. Close the Lift must clear vehicle door(s). From inside, door-mounted position the unit as close to the control box.
- Page 14 Lift Installation Instructions Lift Positioning (continued) Rear Door and Extensive Floor-to-Ground Installations: 1/2" Figure G Minimum Position the lift in the rear door Rear Door and Clearance opening as outlined on pages Extensive 10 and 11. Depending on the Floor-to-Ground particular lift model installed Installations and the particular vehicle...
-
Page 15: Lift Securement
Lift Installation Instructions Lift Securement Base Plate Mounting Optimum Bolt Locations There must be a total of eight Mounting Mounting Figure I 3/8"-16 x 4" carriage bolts (or 8" Bolts Bolts bolts) securing the base plate Inboard through the floor. Two 3/8"-16 x 8"... - Page 16 Lift Installation Instructions Lift Securement (continued) Underfloor Reinforcement Brackets (continued) Two base plate mounting bolts must secure Technical Assistance: If the reinforcement brack- each bracket. ets will not work as detailed for your particular installation, call 1-800-THE LIFT for technical Underfloor reinforcement brackets must reach assistance.
- Page 17 Lift Installation Instructions External Tooth Star Washers Eight 3/8" external tooth star washers are supplied Through Chassis: When securing base plate with each lift. Position star washers as follows. mounting bolts through chassis subframe members, position a star washer between the chassis and the Through Floor Only: When base plate mounting 3/8"...
- Page 18 Lift Installation Instructions Lift Securement (continued) Bolt Tightening Mounting Bolt Torque Speci- Tightening of the base plate alignment of towers and vertical mounting bolts directly affects arms while tightening. See Figure fications: 28 to 31 foot pounds. Adjustment to mount- vertical arm alignment and base M.
-
Page 19: Power Cable And Ground Cable Installation
Lift Installation Instructions Power Cable and Ground Cable Installation Millennium pump modules feature a pump- CAUTION mounted ground cable and an external stud for connection of the lift power cable. A 1" I.D. plastic Position and secure grommet is provided for the power cable and ground cable clear ground cable access hole. - Page 20 Lift Installation Instructions Power Cable and Ground Cable Installation (continued) Lift Ground Secure all cables using cable ties and/or cable clips (mount Two ground cables are provided. clips with self-tap screws). One ground cable is pump mounted (shown in photo on Cable page 17).
- Page 21 Lift Installation Instructions Ground Cables: The pump Power Cable: Route, cut to length and connect the power cable before ground cable and battery-to- frame ground cable must be securing the cable to the vehicle. mounted to a common Connect battery-to-frame ground vehicle framing member to cable to negative (-) battery post.
-
Page 22: Circuit Sentry Installation And Power Connection
Lift Installation Instructions Circuit Sentry Installation and Power Connection Offset Mount Bracket 28498 Figure P Flush Mount Bracket 28755 Circuit Breaker Top Post Mount Positive (+) 12 Volt Battery Post Side Post Mount 3/8-16 x 1" Hex Bolt Spacer Note: Compact Circuit Sentry Compact Circuit Sentry Kit 28910KS Kit 28910KS is currently Item Qty. - Page 23 Lift Installation Instructions Circuit Sentry Kit 28910KS is mounting surface and other W ARNING supplied to provide greater variables. Mounting brackets can installation versatility (less space be oriented as needed. required). Two types of mount- ing brackets are supplied (shown The Circuit Sentry must be in Figure P).
-
Page 24: Control Box And Harness Installation
Lift Installation Instructions Control Box and Harness Installation Groove Guide Quick-Disconnect Harness: “Quick-disconnect” hand-held controls are available with three types of cable (standard, armored and coiled). L915 Series lifts are shipped without the control box harness installed. All harnesses are equipped with the same quick-disconnect sockets. - Page 25 Lift Installation Instructions Control Box Mounting: The control box mounts to storage clip bracket to the door as shown in Figure the inside face of the lift cargo door as shown in the Q on page 22. Insert control box storage clip in center photo below.
-
Page 26: Design Lifting Capacity
Lift Installation Instructions Design Lifting Capacity Millennium Series lifts are rated at ration must support the lift and Positioning and Clearance a design lifting capacity of 800 the lift load. Checklist and corresponding pounds. The combination of lift illustrations. Note: Refer to the base plate, mounting bolts, Note: Visually check alignment Bolt Tightening section and... - Page 27 Lift Installation Instructions Positioning and Clearance Checklist Figure R Alignment: "Side" to "Side" Alignment: As viewed from outside the vehicle, the lift vertical arms and platform (when stowed) should be perpendicular (90°) to the vehicle floor and parallel (aligned) with the sides of doorjamb (see points 8 and 9).
-
Page 28: Base Plate Plugs
Lift Installation Instructions Platform Angle Adjustment and Floor Level Adjustments The platform angle and floor W ARNING level positioning of the bridge plate (inboard roll stop) must be Adjust platform properly adjusted before angle and bridge operating the lift with a pas- plate floor level senger. -
Page 29: Passenger's Seat
Lift Installation Instructions Passenger's Seat (Vans) Reinstall passenger's seat in suitable location using the original (OEM) mounting hardware if previously removed. Torque seat mounting hard- ware per manufacturer's specifications. Owner's Manual Be certain the lift owner's W ARNING (operator's) manual is in the lift- mounted manual storage pouch. -
Page 30: Platform Angle Adjustment Instructions
Platform Angle Adjustment Instructions W ARNING Outboard end of platform Adjust platform angle must contact as detailed here. ground first. Failure to do so may result in serious bodily injury and/or property damage. Wrong Adjusting the platform angle based on the relationship of the platform at ground level Wedges directly affects the angle of the platform when... - Page 31 Platform Angle Adjustment Instructions Adjustment Allen screws are provided on each side end of the platform. Note: Both adjustment screws of the lift platform for adjusting the platform angle. must be adjusted equally. Adjust platform angle as needed. See Figure U on previous page. Apply Turn the adjustment screw clockwise to raise the ®...
-
Page 32: Floor Level Guideline Adjustments
Floor Level Guideline Adjustments Wrong Must make full contact. Gap not permitted. Stop Block Guideline All Lift Models Stop blocks must make full contact with the edge of the vertical arms. Stop Block Vertical Arm Unfold/Down and Up/Fold Microswitches: The Floor Level Guideline Adjustments: The Unfold/Down and Up/Fold microswitches (limit Unfold/Down and Up/Fold microswitches control... - Page 33 Floor Level Guideline Adjustments Wrong Floor Level Guidelines for Automatic Inboard Roll Stop (IB) Lift Models: Note: See page 32 for Floor Level Guidelines for Fixed Inboard Roll Stop (Non-IB) lift Gap not models. permitted. When adjusting microswitches, stop block positioning and bridge plate positioning must be viewed.
- Page 34 Floor Level Guideline Adjustments Floor Level Guidelines for Fixed W ARNING Inboard Roll Stop (Non-IB) Lift Models: Improper microswitch adjustment may Note: See page 31 for Floor Level Guide- result in serious lines for Automatic Inboard Roll Stop (IB) lift bodily injury and/or models.
-
Page 35: Roll Stop Adjustment Instructions
Roll Stop Adjustment Instructions When replacing a roll stop Roll Stop Detail or roll stop hydraulic Latch Lever cylinder, the roll stop must Adapter be properly adjusted during Detail installation procedures. Jam Nut The roll stop cylinder rod must be adjusted to properly position the roll Pivot stop. -
Page 36: Quiet-Ride Adjustment Instructions
Quiet-Ride Adjustment Instructions Adjustable Quiet-Ride Guided Stop Blocks and fixed installation procedures can result in potential rattles rubber bumpers mounted at key locations aid in also. If lift rattles occur, review the details in this eliminating or reducing potential rattles. Improper section for possible source(s) and remedies. - Page 37 Quiet-Ride Adjustment Instructions 4. Bridge Plate Stop Bolts: Stop bolts keep bridge plate tight against Vibration can occur between the bridge plate platform when and the platform when the lift is in the stowed Stop Bolt lift is stowed. (typical both ends) position.
-
Page 38: Lubrication Diagram
Fold Platform Roll Stop Hinge Vertical Arm Pivot Pin See the Maintenance/Lubrication Schedule for recommended applications per number of cycles or elapsed time. Specified (recommended) Available Braun Lubricant Type Lubricant Amount Part No. Light Penetrating Oil LPS2, General Purpose 11 oz. -
Page 39: Maintenance And Lubrication
Platform components exposed to there is any sign of wear, damage or improper operation. contaminants when lowered to the ground may Contact your sales representative or call The Braun require extra attention. Corporation at 1-800-THE LIFT. One of our national... - Page 40 Maintenance and Lubrication Schedule continued Inspect lift for wear, damage or any abnormal Correct as needed. condition 4 Weeks or 400 ® Inspect lift for rattles Adjust as needed. See Quiet-Ride Adjustment Cycles Instructions on pages 34 and 35. Perform all procedures listed in previous section also Platform pivot pin bearings (2) Apply Light Oil - See Lubrication Diagram Platform fold axles (2)
- Page 41 Maintenance and Lubrication Schedule Remove pump module cover and inspect: Resecure, replace or correct as needed. continued • Hydraulic hoses, fittings and connections for wear 3 Months or leaks • Harness cables, wires, terminals and connections for securement or damage 1200 •...
-
Page 42: Systems Descriptions
Systems Descriptions General Operation Braun L915 Fully Automatic lifts Pressing the UNFOLD switch W ARNING are powered by an electric/ unfolds the platform from the stowed position to floor level. hydraulic system operating two Maintenance and single-acting hydraulic main The platform stops automatically... - Page 43 Systems Descriptions Power/Interlock Indicator Light: A green indicator light is built into the pump module that illuminates Pump Module when remote interlock(s) are made (circuit com- plete) and there is power to the lift. Both conditions must be met. The light will shut off if either condition is not met (lift functions are disabled also).
- Page 44 Systems Descriptions Electrical (continued) Quick-Check: W ARNING Read warning posted at right! Note: If this solenoid post is bent Remove all rings, watches, etc. at all, the hydraulic valve will not prior to doing any electrical work operate. near the pump motor. With the lift stowed, hold a paper clip (or other magnetically at- tracted object) near the center...
-
Page 45: Microswitches
Systems Descriptions Adjustment Screw Bridging Microswitch Bridging Microswitch: The bridging microswitch is located at the bottom of the left (rear) vertical arm. See Photos A and B. An adjustment screw is built into the platform stop block. The bridging microswitch will be deactivated if the outboard end of the platform contacts the unloading surface before... -
Page 46: Hydraulics
Systems Descriptions Hydraulics M268 Hydraulic Pump: Fixed displacement solenoid/valves when the DOWN switch is pressed. external gear type hydraulic pump with 12 VDC electric motor and 76 cubic inch fluid reservoir. The Troubleshooting: A problem with this solenoid/ pressure relief valve is factory set at 2100 psi. valve can be electrical or hydraulic. - Page 47 Systems Descriptions pressing the DOWN switch then dependent upon platform load. hydraulic fluid to flow only from the energizes this solenoid/valve. roll stop cylinder to the reservoir The manifold Unfold solenoid/ Releasing the DOWN switch de- once the roll stop latch releases valve is de-energized, which energizes the solenoid/valve the roll stop (allowing the roll stop...
- Page 48 Contact The Braun the maximum oil pressure in the not lift load) and then, only after Corporation before system to a safe level. It also contacting The Braun Corpora- adjusting hydraulic keeps the amp draw and battery tion. pressure relief valve.
-
Page 49: Troubleshooting
Systems Descriptions Manual Backup Pump: The manual hydraulic Priming and Flushing Procedure: backup pump system is used to unfold, lower, raise and fold the platform in the event of electrical failure. a. Lower platform fully. See the lift posted Manual Operating Instructions b. -
Page 50: Troubleshooting Diagnosis Chart
Troubleshooting and yourself. Contact your sales by process of elimination. A repair procedures representative or call The Braun Wiring Diagram, Electrical must be performed Corporation at 1-800-THE LIFT. Schematic, Hydraulic Diagram as specified by an... - Page 51 Troubleshooting Diagnosis Chart FUNCTION SYMPTOM POSSIBLE CAUSE REMEDY continued continued 2.22 Misalignment or damage to: Correct/Replace/Lubricate. See • Parallel arms and/or pivot pins Maintenance and Lubrication Schedule • Rotating pivot slide arms and/ and Diagram or pivot pins • Handrails and/or pivot pins •...
- Page 52 Troubleshooting Diagnosis Chart FUNCTION SYMPTOM POSSIBLE CAUSE REMEDY 5.11 Platform not fully lowered Lower platform 5.12 Obstruction under platform Remove obstruction or lower platform in preventing latch foot from contact- different location (level surface) 5.00 ing surface 5.10 ROLL STOP 5.13 Roll stop damaged (bent, deformed Correct or replace.
- Page 53 Troubleshooting Diagnosis Chart FUNCTION SYMPTOM POSSIBLE CAUSE REMEDY continued continued 8.23 Leak in hydraulic system Repair 8.24 Cylinder(s) leak Repair or replace — See Systems 8.20 Descriptions for details. Motor Runs 8.25 Down solenoid/valve stuck open Replace due to contamination or otherwise Doesn’t Lift defective 8.31 Relief valve set too low...
- Page 54 Troubleshooting Diagnosis Chart FUNCTION SYMPTOM POSSIBLE CAUSE REMEDY 10.11 See 8.11, 8.22, 8.24 and 8.41 10.12 Lost prime Prime. See Systems Descriptions for 10.10 Priming and Flushing procedure 10.00 Up/Fold 10.13 Air leak at backup pump to pump Check tightness or leaks MANUAL (Faulty Operation) interface (O-rings)
-
Page 55: Lift Interlock Installation
Lift Interlock Installation Housing Plate Ground Interlock Prepunched Jumper W/BK Hole GREEN Ground TO SWITCH BOX GREEN TO SWITCH BOX Interlock Installation Instructions 1. To connect remote interlock switch: a. Remove (disconnect) jumper male plug. b. Snap plastic female socket into prepunched housing plate. c. -
Page 56: Lift Electrical Schematic
Lift Electrical Schematic Note: Shown with lift in stowed position. NOTE: ALL WIRES 20 GA. UNLESS OTHERWISE NOTED. LIFT DESCRIPTION SYMBOL SWITCH BOX BATTERY Y (16) UNFOLD Note: Applicable CHASSIS GROUND for 16 gauge BATTERY FOLD wiring harness BK (16) R (2) CIRCUIT BREAKER W (16) -
Page 57: Lift Wiring Diagram
Lift Wiring Diagram Note: Shown with lift in stowed position. COM. Switch Box Unfold / Down (As Viewed From Terminal N.O. Microswitch Side of Switch) N.C. 9-COND WIRE CODE COM. COLOR Up / Fold Fold/Unfold BLACK N.O. Microswitch YELLOW Switch BROWN N.C. -
Page 58: 18 Gauge Lift Control Box Electrical Schematic
18 Gauge Lift Control Box Electrical Schematic LIFT SWITCH BOX Note: Applicable for 18 gauge OR (18) wiring harness control box UNFOLD 900-5903AQD. See page 54 for 16 gauge harness control FOLD BK (18) box schematic. W (18) Note: All other elements of schematic on page 54 are applicable for all lifts. -
Page 59: Hydraulic Schematic
Hydraulic Schematic Description Symbol Description Symbol Pump, Fixed Pressure Compensated Displacement Flow Control 2 Way 2 Position Pump Motor Solenoid Valve 3 Way 2 Position Backup Pump Solenoid Valve Cylinder, Single Relief Valve Acting Pressure Switch Check Valve Unfold Orifice Filter Screen Reservoir, Manual... -
Page 60: Rear Pump Hydraulics Parts List
Rear Pump Hydraulics Parts List Item Qty. Description L915 L916 L917 L918 L919 Item Qty. Description L915IB L916IB L917IB L918IB L919IB Pump Assy. (M268) Bridging with #26578 Fitting 25597A12V-A6 25597A12V-A6 25597A12V-A6 25597A12V-A6 25597A12V-A6 Motor, Pump - 12 Volt 14785-IS 14785-IS 14785-IS 14785-IS 14785-IS... -
Page 61: Rear Pump Hydraulics Diagram
Rear Pump Hydraulics Diagram Note: See pages 60 and 61 for Front Pump Hydraulic Diagram and Parts List. Note: See page 57 for L915 Hydraulic Schematic. Note: Illustrations depict components as equipped when specified lift series was in production. Replace- ment components such as hose assemblies will typically reflect the most current configuration. -
Page 62: Front Pump Hydraulics Parts List
Front Pump Hydraulics Parts List Item Qty. Description L915F L916F L917F L918F L919F Item Qty. Description L915FIB L916FIB L917FIB L918FIB L919FIB Pump Assy. (M268) Bridging with #26578 Fitting 25597A12V-A6 25597A12V-A6 25597A12V-A6 25597A12V-A6 25597A12V-A6 Motor, Pump - 12 Volt 14785-IS 14785-IS 14785-IS 14785-IS 14785-IS... -
Page 63: Front Pump Hydraulics Diagram
Front Pump Hydraulics Diagram Note: See pages 58 and 59 for Rear Pump Hydraulic Diagram and Parts List. Note: See page 57 for L915 Hydraulic Schematic. Note: Illustrations depict components as equipped when specified lift series was in production. Replace- ment components such as hose assemblies will typically reflect the most current configuration. -
Page 64: Rear Pump Module Parts List
(items 28 and 29) if a blue nylon patch is not ® present on the bolts when retrofitting an M268BP pump assembly. Loctite is available from The Braun Corporation under part number 11522-1. Page 62... -
Page 65: Rear Pump Module Diagram
28 and 29) if a blue nylon patch is not present on the bolts when retrofitting an ® M268 pump assembly. Loctite available from The Braun Corporation under part number 11522-1. Not applicable for Control Box 6D and Harness 7D. -
Page 66: Front Pump Module Parts List
(items 28 and 29) if a blue nylon patch is not ® present on the bolts when retrofitting an M268BP pump assembly. Loctite is available from The Braun Corporation under part number 11522-1. Page 64... -
Page 67: Front Pump Module Diagram
28 and 29) if a blue nylon patch is not present on the bolts when retrofitting an M268 pump assembly. Loctite ® available from The Braun Corporation under part number 11522-1. Not applicable for Control Box 6D and Harness 7D. -
Page 68: 42" Floor-To-Ground Automatic Inboard Roll Stop
42" Floor-To-Ground Automatic Inboard Roll Stop Lift Models Repair Parts List Part Numbers of Items Dedicated per Lift Model Item Qty. Description L915IB L915FIB L918IB L918FIB Base Plate Weldment 915R7142W30 915F7142W30 918R7142W33 918F7142W33 Pin, Platform Pivot 915U032430 915U032430 911-5324 911-5324 Platform Weldment 915R63050IBW 915R63050IBW... - Page 69 42" Floor-To-Ground Automatic Inboard Roll Stop Lift Models Exploded View Note: L915 lift models are equipped with a longer Quiet-Ride bracket on the right (front) side. Note: L915 platforms have a modified right Series (front) side plate. • L915IB • L915FIB •...
- Page 70 48" Floor-To-Ground Automatic Inboard Roll Stop Lift Models Exploded View Note: L916 lift models are equipped with a longer Quiet-Ride bracket on the right (front) side. Series Note: L916 platforms • L916IB have a modified right (front) side plate. • L916FIB •...
-
Page 71: 48" Floor-To-Ground Automatic Inboard Roll Stop
48" Floor-To-Ground Automatic Inboard Roll Stop Lift Models Repair Parts List Part Numbers of Items Dedicated per Lift Model Item Qty. Description L916IB L916FIB L917IB L917FIB L919IB L919FIB Base Plate Weldment 916R7148W30 916F7148W30 917R7148W33 917F7148W33 919R7148W34 919F7148W34 Pin, Platform Pivot 915U032430 915U032430 911-5324... -
Page 72: 42" Floor-To-Ground Fixed Inboard Roll Stop
42" Floor-To-Ground Fixed Inboard Roll Stop Non-IB Lift Models Repair Parts List Part Numbers of Items Dedicated per Lift Model Item Qty. Description L915 L915F L918 L918F Base Plate Weldment 915R7142W30 915F7142W30 918R7142W33 918F7142W33 Bridge Switch Assembly 25463RA 25463FA 25463RA 25463FA Pin, Platform Pivot 915U032430... - Page 73 42" Floor-To-Ground Fixed Inboard Roll Stop Non-IB Lift Models Exploded View Note: L915 lift models are equipped with a longer Quiet-Ride bracket on the right (front) side. Note: L915 platforms Series have a modified right (front) side plate. • L915 •...
-
Page 74: 48" Floor-To-Ground Fixed Inboard Roll Stop
48" Floor-To-Ground Fixed Inboard Roll Stop Non-IB Lift Models Exploded View Note: L916 lift models are equipped with a longer Quiet-Ride bracket on the right (front) side. Series • L916 • L916F Note: L916 platforms have a modified right • L917 (front) side plate. -
Page 75: Non-Ib Lift Models
48" Floor-To-Ground Fixed Inboard Roll Stop Non-IB Lift Models Repair Parts List Part Numbers of Items Dedicated per Lift Model Item Qty. Description L916 L916F L917 L917F L919 L919F Base Plate Weldment 916R7148W30 916F7148W30 917R7148W33 917F7148W33 919R7148W34 919F7148W34 Bridge Switch Assembly 25463RA 25463FA 25463RA... -
Page 76: Decals And Antiskid
Release switch. This unit is designed to protect the electrical system on CLOSE DOOR(S) all Braun hydraulic wheelchair lifts. In the event of failure, U.S. Patent No. 5,261,779 U.S. Patent No. 6,065,924 wait 60 seconds. Then turn RESET lever to reset breaker. - Page 77 Actual Size: 1-13/16" W. x 2-1/16" T. OPERATING INSTRUCTIONS Read warnings and operate lift as outlined on LIFT OPERATING Braun Millennium Series™ Decal #25580 INSTRUCTIONS decal. Lift operating instructions apply to wheelchair passengers and standees. MADE IN Standee Instructions: Standees must...
- Page 78 1. Rotate top clip. LOCK Lift installation and servicing prohibited by Using hand pump handle: anyone who has not been certified by The Braun TO UNFOLD PLATFORM (OUT): Corporation Sales and Service School. Certified 1. Close hand pump valve (turn clockwise).
- Page 79 Decals and Antiskid Antiskid Inspect your lift for any missing or particular size and quantity of W ARNING worn antiskid. Call 1-800-THE antiskid is dependent on lift LIFT for replacements. Use of model. Order as needed. Replace missing or worn antiskid. Antiskid Failure to do so may result in serious...
-
Page 80: Lift Specifications
Lift Specifications The following specifications are basic to the electrical/hydraulics operations. Further technical specifications and details of components are provided in the Systems Descriptions and Troubleshooting sections located within this manual. Note: Lift weights applicable for rear and front pump lift models. Lift Model L915 L915IB... - Page 81 Lift Specifications OPERATIONS CYCLE TIME CHARTS POWERED OPERATIONS - 42" Floor-to-Ground Duration Average Average Length of Travel Operation Length of Travel Minimum to Maximum Duration per Duration Platform Unfold Full Stroke Cycle 7.91 sec. to 10.24 sec. 9.08 sec. Full Stroke Cycle Platform Lower 42"...
-
Page 82: Lift Dimensions
Installation Notes for details. Braun Bus Door Kits: cannot be listed due to the many possibilities. If in doubt, Braun Retrofit Bus Door Kits are available to provide the consult the factory. required clear opening dimensions. - Page 83 Lift Dimensions Rear Pump Front Pump Lift Models Lift Models Automatic Inboard Roll Stop (IB) *Automatic Inboard Roll Stop (IB) Automatic Inboard Roll Stop (IB) Important: Minimum Clear Door Opening Dimensions are defined as finished door opening, including any intrusive doorjambs, headers, sills or hinges.
-
Page 84: Warranty And Registration Policy
03/20/2003 CITY PATENT PENDING-5,261,779-6,065,924-6,238,169 TELEPHONE STATE TO VALIDATE WARRANTY REGISTRATION CARDS MUST BE RETURNED TO THE BRAUN CORPORATION. Sample Warranty/Registration Card Sample Serial No./Series No. Identification Tag Model No. Pump Code Note: This information must be provided when filing a Series No. - Page 85 Daily Preventive Maintenance Schedule Vehicle Number: Date: Inspector: Pre-Trip Inspection: Before each scheduled day of lift service, operate lift minimum one complete cycle and inspect each of the following : Does the lift interlock (if equipped) function as intended? Does the lift cargo door light (if equipped) function as intended? Does the lift deploy when the lift interlock is activated as intended? Does the lift safely clear the cargo door as the lift is deployed and stowed? Does the lift operate smoothly (no jerking or abnormal movement)?
- Page 86 Lift Installation Checklist May 2004 Installation Date: Installed By: Lift Model: Inspected By: Lift Serial Number: Warranty/Registration card processed by: Date: Positioning and Clearance Checklist Is the lift centered in the door opening with the lift base plate parallel (aligned) with the door opening (at floor level)? Viewing the lift from outside the vehicle: Are the vertical arms and platform aligned and parallel with the sides of the door jamb...
- Page 87 Has the optional padding kit been installed (if applicable)? Is the lift owner's (operator's) manual stored in the lift-mounted manual storage pouch for the consumer? Has The Braun Corporation Warranty/Registration card been filled out, processed and mailed to The Braun Corporation? See reverse side also...
- Page 88 "Providing Access to the World" ® Over 300 Braun Dealers Worldwide ® "Providing Access to the World" International Corporate Hdqrs: P .O. Box 310 Winamac, IN 46996 USA 1-800-THE LIFT (574) 946-6153 FAX: (574) 946-4670...
- Page 89 All illustrations, descriptions and specifications in this manual are based on the latest product information available at the time of publication. The Braun Corporation reserves the right to make changes at any time without notice. time of publication. The Braun Corporation reserves the right to make changes at any time without notice.