Maintenance And Lubrication; Maintenance And Lubrication Schedule - Braun VISTA Series Installation & Service Manual

Maintenance and Lubrication Schedule

Proper maintenance is necessary to ensure safe,
trouble-free operation. Inspecting the lift for any
wear, damage or other abnormal conditions should
be a part of all transit agencies daily service pro-
gram. Simple inspections can detect potential
problems.
The maintenance and lubrication procedures
specified in this schedule must be performed by a
Braun authorized service representative at the
scheduled intervals according to the number of
cycles or elapsed time, whichever comes first.
VL917 Series lifts are equipped with hardened pins
and self-lubricating bushings to decrease wear,
provide smooth operation and extend the service life
of the lift.
When servicing the lift at the consecutive recom-
mended intervals, inspection and lubrication proce-
dures specified in the previous sections should be
performed (repeated). Clean the components and
the surrounding area before applying lubricants.
LPS2 General Purpose Penetrating Oil is recom-
mended where Light Oil is called out. Use of
improper lubricants can attract dirt or other contami-
nants which could result in wear or damage to the
components. Platform components exposed to
contaminants when lowered to the ground may
require extra attention.
Lift components requiring grease are lubricated
Outboard roll stop hinge pins (Item 1)
Outboard roll stop arm slots (Item 2)
Inboard fold/unfold cable rod end bushings (Item 4)
Outboard fold/unfold cable ends (Item 5)
™
Lift-Tite latches (tower pivot points) (Item 6)
™
Lift-Tite latch gas (dampening) spring pivot
points (Item 7)
4 Weeks
Inspect Lift-Tite
or 400
damage (bent, deformed or misaligned), positive
Cycles
securement (external snap rings) and proper
operation
Inspect outboard roll stop for proper operation
Inspect fold/unfold cables (2) for wear (deterioration
or cracking of plastic sleeve), damage and positive
securement on both ends (4)
Inspect lift for wear, damage or any abnormal
condition
continued
Inspect lift for rattles
1-03 Update
™
latches and gas springs for wear or
during assembly
procedures. When
replacing these compo-
nents, be sure to apply
grease during installa-
tion procedures.
Specified lubricants are
available from The
Braun Corporation (part
numbers provided on
page 34).
All listed inspection,
lubrication and mainte-
nance procedures
should be repeated at
"4 week or 400 cycle" intervals following the scheduled
"1 Year or 4800 Cycles" maintenance. These intervals
are a general guideline for scheduling maintenance
procedures and will vary according to lift use and
conditions. Lifts exposed to severe conditions (weather,
environment, contamination, heavy usage, etc.) may
require inspection and maintenance procedures to be
performed more often than specified.
Discontinue lift use immediately if maintenance and
lubrication procedures are not properly performed, or if
there is any sign of wear, damage or improper operation.
Contact your sales representative or call The Braun
Corporation at 1-800-THE LIFT. One of our national
Product Support representatives will direct you to an
authorized service technician who will inspect your lift .
Apply Light Oil - See Lubrication Diagram
Apply Light Grease - See Lubrication Diagram
Apply Light Grease - See Lubrication Diagram
Apply Light Grease - See Lubrication Diagram
Apply Light Oil - See Lubrication Diagram
Apply Light Oil - See Lubrication Diagram
Resecure, replace defective parts or otherwise
correct as needed. Note: Apply Light Grease to Lift-
™
Tite latch tower pivot point if replacing latch.
Correct, replace defective parts and/or relubricate.
Replace defective parts and resecure as needed.
Correct as needed.
Adjust as needed. See Quiet Ride
Instructions on page 25.
W ARNING
Maintenance and
lubrication proce-
dures must be per-
formed as specified
by an authorized
service technician.
Failure to do so may
result in serious
bodily injury and/or
property damage.
®
Adjustment
Page 31