Define Voice; Record Speech; Speech Box Mode; Diagnostic Test - Visonic POWERMAX PRO Installer's Manual

***
The currently saved option is displayed with a dark box at the right side. To review the options, repeatedly click
button until the desired option is displayed, then click
list, refer to paragraph 4.3 (DEFINE ZONE TYPES).
Each X-10 unit has default zone name ( 01- front door, 02 - garage, 03 - garage door, 04 - back door, 05 – child room, 06 –
office, 07 – dining room, 08- dining room, 09 – kitchen, 10 – living room, 11 – living room, 12 – bedroom, 13 – bedroom, 14 –
guest room, 15 – master bedr).
DEFINE PGM
FLASH ON ALARM
no flash
all light flash
report to C.S. 1
disable
enable

4.9 DEFINE VOICE

4.9.1 Record Speech

This mode allows you to record short-duration speech
messages for the following purposes:
• House identity is a message announced automatically
when events are reported to private telephones.
• 4 User Names can be recorded and assigned to users
numbered 5-8. In case of event, the relevant user
name will be added to the message that will be
reported via the telephone.
(see figure 4.1a)
9. DEFINE VOICE
RECORD SPEECH
HOUSE IDENTITY
- don't release
RECORD A MESSAGE
(*)
TALK NOW
(e.g. "John's house")
RECORDING ENDED
(**)
Release button [2]
VOICE BOX MODE
No Voice Box
Voice Box Only
Voice Box Mixed

4.10 DIAGNOSTIC TEST

This mode allows you to test the function of all protected
area wireless sensors / wireless sirens / wireless keypads
and to receive / review information regarding the received
signal strength. Three reception levels are sensed and
reported:
DE5468IP
DEFINE INT/STRB
TRBL INDICATION
don't indicate
indicate
report to C.S. 2
disable
enable
USER #5 NAME
Record users 5 - 8 names (for example, David, Rose, Mark, etc.).
The process is identical to HOUSE IDENTITY recording process.
(*)
USER TERM #1
Record users terms 1-5 (e.g. Living room, Library, etc.), identical to HOUSE IDENTITY recording process.
(*) RECORD MESSAGE is displayed momentarily. The dark square boxes slowly disappear,
one by one, until end of recording time.
(**) To check the recorded message, press the
Figure 4.9 - Speech Recording Flow Chart
(a dark box will be displayed at the right side). For zone name
X-10 GENERAL DEF
FAIL REPORT
report to PAGER
disable disable
enable enable
Figure 4.8 - Detail A
• 5 custom zone names can be recorded and assigned
to specific zones. These names are useful if none of
the 26 fixed zone names are found suitable for a
certain zone (see fig. 4.3).
The recording process is shown below.

4.9.2 Speech Box Mode

This mode allows you to determine whether two-way voice
communication is to be sounded either via an external
speakerphone, via the PowerMax Pro, or via both.
USER #6 NAME
USER TERM #2 USER TERM #3
Received Signal Strength Indication:
Reception
Strong
Good
Poor
The diagnostic test process is shown in Figure 4.10.
X-10 UNIT DEFINE
3 PHASE & FREQ
disable 3 phase
3 phase 50 Hz
3 phase 60 Hz
Select "start"/"stop"and
enter the desired time.
rep to private
disable
enable
USER #7 NAME
USER TERM #4
key and listen to the playback.
Buzzer Response
Happy Tune twice ( - - - –––– ) ( - - - ––––)
Happy Tune ( - - - –––– )
Sad tune ( –––––––– )
LOCKOUT TIME
start - HH:MM A
stop - HH:MM A
xxxx - 00:00 A
send SMS
USER #8 NAME
USER TERM #5
25