一般仕様 - Yamaha PM 5000 Owner's Manual

各種資料
仕様
1. 一般仕様
0dBu is referenced to 0.775 Vrms.
Total Harmonic Distortion
(Master Output)
Frequency Response
(Master Output)
Hum & Noise (20Hz∼20kHz)
Rs=150Ω
Input Gain=Maximum
Input Pad =OFF
Input sensitivity=-60dBu
Maximum Voltage Gain
Crosstalk
MONO & ST INPUT PAD
MONO & ST INPUT GAIN
INPUT High Pass Filter
INPUT Equalization *3
HIGH
HI-MID
LO-MID
LOW
Sweep sine wave oscillator/Pink noise with burst
Phantom Power
Input LED Meter
Output LED Meter
96
Less than 0.1%
(THD+N)
0+1,-3dB
*1 -128dBu
-100dBu
-94dBu (98dB S/N)
-87dBu (91dB S/N)
-94dBu (98dB S/N)
-64dBu (68dB S/N)
-89dBu (93dB S/N)
*2
64dB
80dB
90dB
84dB
90dB
64dB
80dB
90dB
84dB
81dB
77dB
87dB
10dB
6dB
-80dB @ 1kHz, -70dB @ 10kHz
-80dB @ 1kHz, -70dB @ 10kHz
26dB
50dB
12dB/octave roll off below 20∼400Hz at -3dB points.
+15, -15dB maximum
1k∼20kHz (peaking/shelving, Q=0.5∼3)
0.4k∼8kHz (peaking, Q=0.5∼3)
80∼1.6kHz (peaking, Q=0.5∼3)
30∼600Hz (peaking/shelving, Q=0.5∼3)
PEAK
+12/+6/+3/0
-3/-6/-12/-25
PEAK
+15/･･/0
-3/･･/-39
20Hz∼20kHz @ +14dBu 600 Ω
(Input Gain Control at Maximum)
20Hz∼20kHz @ +4dBu 600Ω
(Input Gain Control at Maximum)
Equivalent Input Noise.
Residual Output Noise.
STEREO AUX Master fader at nominal level and all assign SW's off.
GROUP/AUX Master fader at nominal level and all assign SW's off.
STEREO, MONO (C) Master fader at nominal level and all assign SW's off.
STEREO AUX, GROUP/AUX, STEREO, MONO (C) Master fader and one input
fader at nominal level.
MATRIX Master at nominal level and all Matrix mix controls at minimum level.
MONO IN to MONO IN INSERT OUT,DIRECT OUT (pre fader)
MONO IN to STEREO AUX OUT (PRE),GROUP/AUX OUT (AUX mode & PRE)
MONO IN to STEREO AUX OUT (POST),GROUP/AUX OUT (AUX mode &
POST)
MONO IN to GROUP/AUX OUT (GROUP mode), STEREO OUT (INPUT to ST),
MONO (C) OUT (INPUT to MONO)
MONO IN to MATRIX OUT (GROUP/AUX MASTER GROUP mode to
MATRIX)
ST IN to ST INSERT OUT
ST IN to STEREO AUX OUT (PRE)
ST IN to STEREO AUX OUT (POST)
ST IN to GROUP/AUX OUT (GROUP mode), STEREO OUT (INPUT to ST)
ST IN to MONO (C) OUT (INPUT to MONO)
ST IN to GROUP/AUX OUT (AUX mode & PRE)
ST IN to GROUP/AUX OUT (AUX mode & POST)
SUB IN to Master OUT
2TR IN to MONITOR OUT
Adjacent inputs.
input to output. (except between L and R)
Variable
4 mode selectable (100Hz/1kHz/10kHz/PINK)
Selectable FIX or SWEEP for 100Hz/1kHz/10kHz by SWEEP/BURST ON/OFF
switch, sweep range: x0.2 - x2, Less than 1% T.H.D. @ +4dBu
Selectable continue or BURST for PINK noise by SWEEP/BURST ON/OFF
switch.
PINK NOISE ：fixed 200msec, INTERVAL ：variable 1sec∼20sec
+48VDC is applied to balanced inputs for powering condenser microphones via
6.8kΩcurrent-limiting/isolation resistors.
9-points (PEAK/+12/+6/+3/0/-3/-6/-12/-25dB) LED level meter built into each
MONO-IN and ST-IN module.
LED (red) turns on when pre-EQ level or post-EQ level or pre-Fader level
reaches 3dB below clipping.
LED (yellow) turns on when pre-Fader level reaches +12/+6/+3/0dB.
LED (green) turns on when pre-Fader level reaches -3/-6/-12/-25dB.
20-points (PEAK, +15, <3dB step>, -39dB) LED level meter.
STEREO AUX 1 (L, R)∼12 (L, R), STEREO MATRIX 1 (L, R)∼4 (L, R)
(STEREO AUX/STEREO MATRIX selectable)
GROUP/AUX 1∼8, MATRIX 1∼8 (GROUP/AUX, MATRIX selectable)
STEREO (L, R), MONO (C)
CUE (L, R, C), TB/OSC (CUE C, TB/OSC automatic select)
LED (red) turns on when pre-LineAmp level reaches 3dB below clipping.
LED (yellow) turns on when pre-LineAmp level reaches +15/<3dB step>/0dB.
LED (green) turns on when pre-LineAmp level reaches -3/<3dB step>/-39dB.