1. Manuals
  2. Brands
  3. Raven Manuals
  4. Paint Sprayer
  5. AutoBoom
  6. Installation manual

Raven AutoBoom Installation Manual

Case ih patriot model year 2010 & newer
Hide thumbs Also See for AutoBoom:
Table of Contents

Advertisement

Quick Links

Download this manual
Case IH Patriot, Model Year 2010 &
Newer AutoBoom™ Installation
Manual
P/N 016-0230-095 Rev D
06/15
E20327
Copyright 2010, 2011, 2012

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AutoBoom and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Raven AutoBoom

Summary of Contents for Raven AutoBoom

  • Page 1 Case IH Patriot, Model Year 2010 & Newer AutoBoom™ Installation Manual P/N 016-0230-095 Rev D 06/15 E20327 Copyright 2010, 2011, 2012...
  • Page 2 GPS, GNSS, SBAS, etc.). Therefore, Raven Industries cannot guarantee the accuracy, integrity, continuity, or availability of these services and cannot guarantee the ability to use Raven systems, or products used as components of systems, which rely upon the reception of these signals or availability of these services.

  • Page 3: Table Of Contents

    ....................7 Install the PowerGlide Plus Hydraulic System ............... 11 Remove the Orifice Fittings ....................11 Install the Fittings on the AutoBoom Valve ................ 14 Mount the AutoBoom Valve ....................14 Install the Left and Right Cylinder Hoses ................16 Install the Left and Right Down Hoses ................
  • Page 4 Connect the Harness to the Power/CAN Controls ............. 42 Connect the Power Leads ....................43 Chapter 5 Replacement Parts ............... 45 Valves ............................. 45 Wheels ............................ 46 Sensors ........................... 46 Case IH Patriot, Model Year 2010 & Newer AutoBoom™ Installation Manual...

  • Page 5: Important Safety Information

    Raven dealer for support. • Follow all safety labels affixed to the AutoBoom system components. Be sure to keep safety labels in good condition and replace any missing or damaged labels. To obtain replacements for missing or damaged safety labels, contact your local Raven dealer.

  • Page 6: Hydraulic Safety

    CAUTION Hydraulic Safety • Raven Industries recommends that appropriate protective equipment be worn at all times when working on the hydraulic system. • Never attempt to open or work on a hydraulic system with the equipment running. Care should always be taken when opening a system that has been previously pressurized.

  • Page 7: Introduction

    Be sure to identify which system you have and follow only the instructions for that system. Preparing for Installation Before installing AutoBoom, park the machine where the ground is level, clean, and dry. Leave the machine turned off for the duration of the installation process.

  • Page 8: Recommendations

    Recommendations Raven Industries recommends the following best practices before installing or operating the AutoBoom system for the first time, at the start of the season, or when moving the AutoBoom system to another machine: • Ensure the machine’s hydraulic filters have been recently changed and there are no issues with the machine’s hydraulic system (e.g., pump issues, faulty hydraulic motors, fine metal deposits in the hydraulic...

  • Page 9: Updates

    Software and manual updates are available on the Raven Applied Technology website: http://www.ravenhelp.com At Raven Industries, we strive to make your experience with our products as rewarding as possible. One way to improve this experience is to provide us with feedback on this manual.
  • Page 10 Chapter 2 Case IH Patriot, Model Year 2010 & Newer AutoBoom™ Installation Manual...

  • Page 11: Powerglide Plus

    PowerGlide Plus Kit Contents This section contains a list of the components that are included in the PowerGlide Plus AutoBoom kit. Before beginning the AutoBoom installation, compare the items in the AutoBoom kit with the components on this list. If you have questions about the kit, contact your Raven dealer.
  • Page 12 Fitting - 11/16” ORFS M/M/F Swivel Run Tee 333-0012-069 Fitting - 11/16” ORFS (M) to 9/16” SAE O- 333-0012-084 Ring (M) Straight Adapter Fitting - 11/16” ORFS (M) to 3/4” SAE O-Ring 333-0012-165 (M) 90° Elbow Case IH Patriot, Model Year 2010 & Newer AutoBoom™ Installation Manual...
  • Page 13 11/16 ORFS (F) - 44” PowerGlide Plus Wheel Kit (P/N 117-0134-006) TABLE 3. Picture Item Description Part Number Qty. Axle Assembly - Right Cushioned AutoBoom 063-0131-585 Axle Assembly - Left Cushioned AutoBoom 063-0131-590 Bracket - Left Weldment Receiver 116-0159-544 Bracket - Hub Retainer...
  • Page 14 PowerGlide Plus Wiring Kit (P/N 117-0137-023) TABLE 4. Picture Item Description Part Number Qty. Not Pictured Manual - AutoBoom Calibration & Operation 016-0130-062 AutoBoom Node 063-0130-010 Cable - Harness 115-0230-045 Cable - Power/CAN 115-0230-007 Case IH Patriot, Model Year 2010 & Newer AutoBoom™ Installation Manual...

  • Page 15: Install The Powerglide Plus Hydraulic System

    Remove the Orifice Fittings Before populating the hydraulic fittings on the AutoBoom valve, it is necessary to remove orifice fittings from the valve in the PowerGlide Plus system. Failure to remove these fittings from the valve will restrict the down speed of the booms when the system is enabled.
  • Page 16 Remove the coils from the solenoids near Ports 3A and 3B to gain easy access to those ports. Port Plugs Removed from the AutoBoom Valve FIGURE 3. Use an Allen wrench to remove the plugs from Ports 3A and 3B. Case IH Patriot, Model Year 2010 & Newer AutoBoom™ Installation Manual...
  • Page 17 Remove the orifice fittings from Ports 3A and 3B. Important: Tip the AutoBoom valve on its side and use the Allen wrench to remove the orifice from the cavity, taking care not to let the fitting fall into the valve.

  • Page 18: Install The Fittings On The Autoboom Valve

    Install the Fittings on the AutoBoom Valve Before mounting the AutoBoom valve on the machine, install the fittings in the appropriate ports of the AutoBoom valve. This prepares the valve for installation and simplifies the hose connection process later in the procedure.
  • Page 19 Connect the 90° end of the supplied hydraulic hose (P/N 214-1000-311) to the 90° end of the tee fitting. Connect the straight end of the installed hydraulic hose to Port P of on the AutoBoom valve. Disconnect the machine’s tank hose from the machine’s hydraulic valve.

  • Page 20: Install The Left And Right Cylinder Hoses

    Install the 90° end of the supplied hydraulic hose (P/N 214-1000-494) on the 90° end of the installed tee fitting. Connect the straight end of the installed hydraulic hose to the fittings installed in Port RC of the AutoBoom valve.

  • Page 21: Install The Left And Right Down Hoses

    Connect the straight end of the installed hydraulic hose to the fitting installed in Port RT CYL RTN of the AutoBoom valve. Connect the machine’s left return hose to the opposite end of the tee fitting installed in the left return port.

  • Page 22: Powerglide Plus Hydraulic Schematic

    Chapter 3 PowerGlide Plus Hydraulic Schematic Case IH Patriot, Model Year 2010 & Newer AutoBoom™ Installation Manual...

  • Page 23: Install The Gauge Wheels

    PowerGlide Plus Install the Gauge Wheels Gauge Wheel Mounting Locations Wheel mounting locations may be influenced by the boom configuration. Determine the appropriate location for mounting the wheels on the boom, ensuring the wheels will not interfere with or be damaged while folding or unfolding the booms.
  • Page 24 Secure the gauge wheel assembly in the wheel mounting bracket by installing two 1/2”-13 x 1-1/2” SS hex bolts (P/N 311-0052-186) and two 1/2”-13 zinc hex nuts (P/N 312-1000-043). Repeat the steps above to install the left wheel. Case IH Patriot, Model Year 2010 & Newer AutoBoom™ Installation Manual...

  • Page 25: Install The Powerglide Plus Wiring

    Install the AutoBoom Node AutoBoom Node Installed FIGURE 13. Mount the AutoBoom node (P/N 063-0130-010) to the AutoBoom valve hydraulic mounting plate (P/N 107- 0171-802) using three 3/8”-16 zinc hex bolts (P/N 311-0054-106) and three 3/8”-16 zinc flanged lock nuts (P/N 312-1001-164).

  • Page 26: Connect The Harness To The Power/Can Controls

    Locate the machine’s harness cable bulkhead on the center boom section, near the pressure transducers on the sprayline. Disconnect the machine’s cable from the bulkhead connector. Attach the appropriate ends of the AutoBoom cable (P/N 115-0230-073) to the machine’s cable and the bulkhead connector Machine’s CAN Terminator.

  • Page 27: Connect The Power Leads

    Machine’s CAN Terminator Connected to the AutoBoom Harness Cable FIGURE 16. Connect the machine’s CAN terminator to the AutoBoom harness cable’s (P/N 115-0230-073) CAN connection. Connect the AutoBoom harness cable’s CAN connection to the open CAN connection on the machine’s harness. Connect the Power Leads Power Leads Connected FIGURE 17.
  • Page 28 Chapter 3 Case IH Patriot, Model Year 2010 & Newer AutoBoom™ Installation Manual...

  • Page 29: Ultraglide

    This section contains a list of the components that are included in the UltraGlide AutoBoom kit. Before beginning the AutoBoom installation, compare the items in the AutoBoom kit with the components on this list. If you have questions about the kit, contact your Raven dealer.
  • Page 30 Bolt - 5/16”-18 x 7/8” Hex 311-0052-104 Bolt - 3/8”-16 UNC x 1-1/4” Zinc Plated Hex 311-0054-106 Nut - 3/8”-16 Zinc Flanged Lock 312-1001-164 Washer - 5/16” Zinc Plated Lock 313-1000-019 Case IH Patriot, Model Year 2010 & Newer AutoBoom™ Installation Manual...
  • Page 31 UltraGlide Hydraulic Kit (P/N 117-0134-075) TABLE 2. Picture Item Description Part Number Qty. Fitting - 13/16” ORFS M/M/F Swivel Run Tee 333-0012-028 Fitting - 11/16” ORFS M/F 90° Swivel Elbow 333-0012-065 Fitting - 11/16” ORFS M/M/F Swivel Run Tee 333-0012-069 Fitting - 11/16”...
  • Page 32 Part Number Qty. Axle Assembly - Right Cushioned AutoBoom 063-0131-585 Axle Assembly - Left Cushioned AutoBoom 063-0131-590 Bracket - Left Weldment Receiver 116-0159-544 Bracket - Hub Retainer 107-0171-617 Wheel 322-0131-008 Case IH Patriot, Model Year 2010 & Newer AutoBoom™ Installation Manual...
  • Page 33 Nut - 3/8”-16 Zinc Flanged Lock 312-1001-164 UltraGlide Wiring Kit (P/N 117-0137-024) TABLE 5. Picture Item Description Part Number Qty. Not Pictured Manual - AutoBoom Calibration & Operation 016-0130-062 Node - UltraGlide AutoBoom 063-0130-013 Cable - Sensor 115-0171-527 Cable - Harness 115-0230-045 Cable - Power/CAN 115-0230-007 Manual No.

  • Page 34: Install The Ultraglide Hydraulic System

    Install the Fittings on the AutoBoom Valve Before mounting the AutoBoom valve on the machine, install the fittings in the appropriate ports of the AutoBoom valve. This prepares the valve for installation and simplifies the hose connection process later in the procedure.

  • Page 35: Mount The Autoboom Valve

    AutoBoom Valve Mounted on the Valve Mounting Plate FIGURE 1. Secure the AutoBoom valve (P/N 063-0131-124) to the mounting plate (P/N 107-0171-802) using four 5/16” hex bolts (P/N 311-0052-104) and four 5/16” lock washers (P/N 313-1000-019). AutoBoom Valve Mounted on the Machine FIGURE 2.
  • Page 36 Connect the 90° end of the supplied hydraulic hose (P/N 214-1000-311) to the 90° end of the tee fitting. Connect the straight end of the installed hydraulic hose to Port P of on the AutoBoom valve. Disconnect the machine’s tank hose from the machine’s hydraulic valve.

  • Page 37: Install The Left And Right Cylinder Hoses

    Install the 90° end of the supplied hydraulic hose (P/N 214-1000-494) on the 90° end of the installed tee fitting. Connect the straight end of the installed hydraulic hose to the fittings installed in Port RC of the AutoBoom valve.

  • Page 38: Install The Left And Right Down Hoses

    Install the 90° end of the supplied hydraulic hose (P/N 214-1000-494) on the 90° end of the installed tee fitting. Connect the straight end of the installed hydraulic hose to the fitting installed in Port LF CYL RTN of the AutoBoom valve. Case IH Patriot, Model Year 2010 & Newer AutoBoom™ Installation Manual...

  • Page 39: Ultraglide Hydraulic Schematic

    UltraGlide UltraGlide Hydraulic Schematic Manual No. 016-0230-095 Rev. D...

  • Page 40: Install The Ultraglide Sensors

    FIGURE 6. Mount the Boom Sensors WARNING The machine must remain stationary and switched off, with the booms unfolded and supported, during installation or maintenance. Mounted Boom Sensor FIGURE 7. Case IH Patriot, Model Year 2010 & Newer AutoBoom™ Installation Manual...

  • Page 41: Mount The Center Rack Sensor

    UltraGlide Locate the left and right ultrasonic sensors (P/N 063-0130-012 and 063-0130-014) in the AutoBoom installation kit. Remove the sensor from the existing plastic arm. Install the sensors on the 12” S-type sensor arms (P/N 063-0131-592) using the supplied 5/16”-18 x 1-1/4”...

  • Page 42: Connect The Sensor Cables

    Loop and tie-off any excess cable, allowing enough cable for boom folding and extension. Repeat the steps above to connect the remaining sensor cable(s). Note: The sensor cables will be connected to the AutoBoom system in the wiring phase of installation. Case IH Patriot, Model Year 2010 & Newer AutoBoom™ Installation Manual...

  • Page 43: Install The Gauge Wheels - Optional

    UltraGlide Install the Gauge Wheels - Optional Gauge Wheel Mounting Locations Wheel mounting locations may be influenced by the boom configuration. Determine the appropriate location for mounting the wheels on the boom, ensuring the wheels will not interfere with or be damaged while folding or unfolding the booms.
  • Page 44 Secure the gauge wheel assembly in the wheel mounting bracket by installing two 1/2”-13 x 1-1/2” SS hex bolts (P/N 311-0052-186) and two 1/2”-13 zinc hex nuts (P/N 312-1000-043). Repeat the steps above to install the left wheel. Case IH Patriot, Model Year 2010 & Newer AutoBoom™ Installation Manual...

  • Page 45: Install The Ultraglide Wiring

    Install the AutoBoom Node AutoBoom Node Installed FIGURE 11. Mount the AutoBoom node (P/N 063-0130-013) to the AutoBoom valve hydraulic mounting plate using three 3/8”-16 zinc hex bolts (P/N 311-0054-106) and three 3/8”-16 zinc flanged lock nuts (P/N 312-1001- 164).

  • Page 46: Connect The Harness To The Power/Can Controls

    Locate the machine’s harness cable bulkhead on the center boom section, near the pressure transducers on the sprayline. Disconnect the machine’s cable from the bulkhead connector. Attach the appropriate ends of the AutoBoom cable (P/N 115-0230-073) to the machine’s cable and the bulkhead connector Machine’s CAN Terminator.

  • Page 47: Connect The Power Leads

    Machine’s CAN Terminator Connected to the AutoBoom Harness Cable FIGURE 14. Connect the machine’s CAN terminator to the AutoBoom harness cable’s (P/N 115-0230-073) CAN connection. Connect the AutoBoom harness cable’s CAN connection to the open CAN connection on the machine’s harness. Connect the Power Leads Power Leads Connected FIGURE 15.
  • Page 48 Chapter 4 Case IH Patriot, Model Year 2010 & Newer AutoBoom™ Installation Manual...

  • Page 49: Replacement Parts

    R eplacement Parts CHAPTER C h a p t e r 5 This section contains replacement part diagrams for PowerGlide Plus and UltraGlide systems. Refer to these diagrams when calling to request replacement parts. Valves Manual No. 016-0230-095 Rev. D...

  • Page 50: Wheels

    Chapter 5 Wheels Sensors Case IH Patriot, Model Year 2010 & Newer AutoBoom™ Installation Manual...
  • Page 51 Mounting the Gauge Wheels 19 Installing the AutoBoom Node 41 Hydraulic System 11 Wiring Connections 41 Hydraulic Schematic 18 Kit Contents 25 Installing Fittings on the AutoBoom Valve 11 Installing the Fittings on the AutoBoom Valve 14 Installing Left Right...
  • Page 52 Index Case IH Patriot, Model Year 2010 & Newer AutoBoom™ Installation Manual...
  • Page 53 Bring the defective part and proof of purchase to your Raven dealer. If the dealer approves the warranty claim, the dealer will process the claim and send it to Raven Industries for final approval. The freight cost to Raven Industries will be the customer’s responsibility. The Return...
  • Page 54 How Can I Get Service? Bring the defective part and proof of purchase to your Raven dealer. If the dealer approves the warranty claim, the dealer will process the claim and send it to Raven Industries for final approval.

Table of Contents