1. Manuals
  2. Brands
  3. Raven Manuals
  4. Paint Sprayer
  5. AutoBoom
  6. Installation manual

Raven AutoBoom Installation Manual

New holland guardian f/miller nitro n7 series with mono boom
Hide thumbs Also See for AutoBoom:
Table of Contents

Advertisement

Quick Links

Download this manual
New Holland Guardian F/Miller
Nitro N7 Series with Mono
Boom AutoBoom® Installation
Manual
P/N 016-0230-124 Rev. A
08/17
E29653
Copyright 2017

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the AutoBoom and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Raven AutoBoom

Summary of Contents for Raven AutoBoom

  • Page 1 New Holland Guardian F/Miller Nitro N7 Series with Mono Boom AutoBoom® Installation Manual P/N 016-0230-124 Rev. A 08/17 E29653 Copyright 2017...
  • Page 2 GPS, GNSS, SBAS, etc.). Therefore, Raven Industries cannot guarantee the accuracy, integrity, continuity, or availability of these services and cannot guarantee the ability to use Raven systems, or products used as components of systems, which rely upon the reception of these signals or availability of these services.

  • Page 3: Table Of Contents

    Cab Component Installation................25 Wiring Connections ..............................25 Install the AutoBoom Node ..........................25 Connect the AutoBoom Harness to the AutoBoom Valve ............... 26 Connect the AutoBoom Harness to the Machine’s Harness ..............26 Connect the Harness Cable to the Sensors ....................
  • Page 4 Table of Contents New Holland Guardian F/Miller Nitro N7 Series with Mono Boom AutoBoom® Installation Manual...

  • Page 5: Important Safety Information

    Raven dealer for support. • Follow all safety labels affixed to the AutoBoom system components. Be sure to keep safety labels in good condition and replace any missing or damaged labels. To obtain replacements for missing or damaged safety labels, contact your local Raven dealer.

  • Page 6: Hydraulic

    HAPTER WARNING • When starting the machine for the first time after installing AutoBoom, be sure that all persons stand clear, in case a hose has not been properly tightened. • The machine must remain stationary and switched off, with the booms unfolded and supported, during installation or maintenance.

  • Page 7: Electrical

    IMPORTANT SAFETY INFORMATION Routing should not allow hoses to: • Hang below the unit • Have the potential to become damaged due to exposure to the exterior environment. (i.e. tree limbs, debris, attachments) • Be placed in areas of or in contact with machine components which develop temperatures higher than the temperature rating of hose components •...

  • Page 8: Instructions For Wire Routing

    • Clamp harnesses securely to force controlled movement to occur in the desired harness section • Avoid sharp twisting or flexing of harnesses in short distances • Connectors and splices should not be located in harness sections that move New Holland Guardian F/Miller Nitro N7 Series with Mono Boom AutoBoom® Installation Manual...
  • Page 9 IMPORTANT SAFETY INFORMATION Protect harnesses from: • Foreign objects such as rocks that may fall or be thrown by the unit • Buildup of dirt, mud, snow, ice, submersion in water and oil • Tree limbs, brush and debris • Damage where service personnel or operators might step or use as a grab bar •...
  • Page 10 HAPTER New Holland Guardian F/Miller Nitro N7 Series with Mono Boom AutoBoom® Installation Manual...

  • Page 11: Chapter 2 Introduction

    FIGURE 1. Miller Nitro N7 Series with Mono Boom PREPARING FOR INSTALLATION Before installing AutoBoom, park the machine where the ground is level, clean, and dry. Leave the machine turned off for the duration of the installation process. During the installation process, follow good safety practices. Be sure to carefully read the instructions in this manual as you complete the installation process.

  • Page 12: Recommendations

    Raven Industries recommends the following best practices before installing or operating the AutoBoom system for the first time, at the start of the season, or when moving the AutoBoom system to another machine: • Ensure the machine’s hydraulic filters have been recently changed and there are no issues with the machine’s hydraulic system (e.g., pump issues, faulty hydraulic motors, fine metal deposits in the hydraulic hoses, etc.).

  • Page 13: Updates

    This section contains a list of the components that are included in the UltraGlide AutoBoom kit. Before beginning the AutoBoom installation, compare the items in the AutoBoom kit with the components on this list. If you have questions about the kit, contact your local Raven dealer.
  • Page 14 Item Description Part Number Qty. Fitting - -8 ORFS M/M/F Swivel Run Tee Adapter 333-0012-028 Fitting - -6 ORFS (M) to -6 SAE O-Ring (M) 45° Elbow 333-0012-083 New Holland Guardian F/Miller Nitro N7 Series with Mono Boom AutoBoom® Installation Manual...
  • Page 15 INTRODUCTION TABLE 2. Hydraulic Kit (P/N 117-0134-111) Item Description Part Number Qty. Fitting - -8 ORFS (M) to -8” SAE O-Ring (M) Straight Adapter 333-0012-168 Fitting - -6 SAE O-Ring (M) to 11/16” Hex Plug 333-0012-194 Fitting - -8 ORFS (M) to -8 SAE O-Ring (M) 90° Elbow 333-0012-229 Hydraulic Hose - -8 ORFS (F) to 8 ORFS (F) 90°...
  • Page 16 HAPTER New Holland Guardian F/Miller Nitro N7 Series with Mono Boom AutoBoom® Installation Manual...

  • Page 17: Hydraulic System Installation

    AutoBoom valve. NOTICE The appearance of the AutoBoom hydraulic valve may vary slightly from the images contained in this manual. However, the fittings, hose connections, and cable connections remain the same.

  • Page 18: Install The Fittings In The Autoboom Valve

    7/8” hex bolts (P/N 311-0052-104) and four 5/16” split lock washers (P/N 313-1000-019). NOTE: The AutoBoom valve should be installed so that Port LC and RC face the center of the machine. 2. Tighten the bolts to ensure the valve is securely installed.

  • Page 19: Install The Pressure And Tank Hoses

    FIGURE 3. Pressure Hose Installed on AutoBoom Valve Installed Hydraulic Hose (P/N 214-1001-136) in Port P of AutoBoom Valve 4. Connect the 90° end of the installed hydraulic hose to the fitting installed in Port P of the AutoBoom valve. P/N 016-0230-124 Rev. A...
  • Page 20 (P/N 214-1001-137) in Port T of AutoBoom Valve 9. Connect the straight end of the installed hydraulic hose to the fitting installed in Port T of the AutoBoom valve. New Holland Guardian F/Miller Nitro N7 Series with Mono Boom AutoBoom® Installation Manual...

  • Page 21: Install The Left And Right Cylinder Hoses

    FIGURE 7. Left Cylinder Hose Installed on AutoBoom Valve 4. Connect the straight end of the installed hydraulic hose to the fitting installed in Port LC of the AutoBoom valve. 5. Install the machine’s left cylinder hose on the remaining end of the installed tee fitting.
  • Page 22 FIGURE 9. Right Cylinder Hose Installed on AutoBoom Valve 9. Connect the straight end of the installed hydraulic hose to the fitting installed in Port RC of the AutoBoom valve. 10. Install the machine’s right cylinder hose on the remaining end of the installed tee fitting.

  • Page 23: Autoboom Hydraulic Schematic

    HYDRAULIC SYSTEM INSTALLATION AUTOBOOM HYDRAULIC SCHEMATIC P/N 016-0230-124 Rev. A...
  • Page 24 HAPTER New Holland Guardian F/Miller Nitro N7 Series with Mono Boom AutoBoom® Installation Manual...

  • Page 25: Chapter 4 Ultrasonic Sensor Installation

    U LTRASONIC SENSOR CHAPTER C H A P T E R 4 INSTALLATION BOOM SENSOR MOUNTING LOCATIONS Sensor mounting locations may be influenced by the boom configuration. If an object enters the sensor’s blind range unexpectedly, a false echo return to the sensor could occur, causing the boom to drop and the sensor or boom to be damaged.

  • Page 26: Mount The Boom Sensors

    5. Install another 5/16” flat washer (P/N 313-2300-012) on the end of the installed hex bolt and secure it using one 5/16”-18 nylon insert lock nut (P/N 312-4000-059). 6. Repeat the steps above to install the second sensor bracket. New Holland Guardian F/Miller Nitro N7 Series with Mono Boom AutoBoom® Installation Manual...
  • Page 27 ULTRASONIC SENSOR INSTALLATION FIGURE 4. Installed Boom Sensors 90’ - 100’ Booms 120’ Booms Dual Sensor Mounting Locations Outer Sensor Inner Sensor 7. Mount the sensor bracket on the left boom using two 3-1/16” W x 4” L x 3/8” thread U-bolts (P/N 107-0171-608) and four 3/8”-16 zinc flanged lock nuts (P/N 312-1001-164).

  • Page 28: Mount The Center Rack Sensor

    4. Repeat the steps above to connect the remaining sensor cable(s). NOTE: The sensor cables will be connected to the AutoBoom system in the wiring phase of installation. New Holland Guardian F/Miller Nitro N7 Series with Mono Boom AutoBoom® Installation Manual...

  • Page 29: Cab Component Installation

    3/8”-16 UNC x 1” hex bolts (P/N 311-0054-105) and three 3/8”-16 zinc flanged lock nuts (P/N 312-1001-164). 2. Install the large, rectangular node connectors of the AutoBoom harness cable (P/N 115-0230-151) in the correct ports of the node.

  • Page 30: Connect The Autoboom Harness To The Autoboom Valve

    HAPTER CONNECT THE AUTOBOOM HARNESS TO THE AUTOBOOM VALVE 1. Connect the LEFT PRESS (PORT G1) and RIGHT PRESS (PORT G4) connectors on the AutoBoom harness cable (P/N 115-0230-151). 2. Route the connectors to the AutoBoom valve (P/N 063-0131-124). 3. Connect the LEFT PRESS (PORT G1) connector to Port G1 of the AutoBoom valve.

  • Page 31: Chapter 6 Replacement Parts

    R EPLACEMENT PARTS CHAPTER C H A P T E R 6 This section contains replacement part diagrams for PowerGlide Plus and UltraGlide systems. Refer to these diagrams when calling to request replacement parts. VALVES P/N 016-0230-124 Rev. A...

  • Page 32: Sensors

    HAPTER SENSORS New Holland Guardian F/Miller Nitro N7 Series with Mono Boom AutoBoom® Installation Manual...
  • Page 33 Index Cab Component Installation Replacement Parts Connecting the AutoBoom Harness to the Sensors AutoBoom Valve Valves Connecting the AutoBoom Harness to the Machine’s Wheels Harness Connecting the Harness Cable to the Sensors Installing the AutoBoom Node Wiring Connections Sensor Installation...
  • Page 34 Index New Holland Guardian F/Miller Nitro N7 Series with Mono Boom AutoBoom® Installation Manual...
  • Page 35 Bring the defective part and proof of purchase to your Raven dealer. If the dealer approves the warranty claim, the dealer will process the claim and send it to Raven Industries for final approval. The freight cost to Raven Industries will be the customer’s responsibility. The Return...
  • Page 36 How Can I Get Service? Bring the defective part and proof of purchase to your Raven dealer. If the dealer approves the warranty claim, the dealer will process the claim and send it to Raven Industries for final approval.

Table of Contents