1. Manuals
  2. Brands
  3. Raven Manuals
  4. Paint Sprayer
  5. AutoBoom
  6. Installation manual

Raven AutoBoom Installation Manual

2007 & older gvm predator
Hide thumbs Also See for AutoBoom:
Table of Contents

Advertisement

Quick Links

Download this manual
AutoBoom™ Installation Manual
GVM Predator - 2007 & Older

Advertisement

Table of Contents
loading

Related Manuals for Raven AutoBoom

Summary of Contents for Raven AutoBoom

  • Page 1 AutoBoom™ Installation Manual GVM Predator - 2007 & Older...
  • Page 2 Raven Industries shall not be held responsible or liable for the effects of atmospheric conditions and sunspot activity on the performance of our products. Raven Industries cannot guarantee the accuracy, integrity, continuity, or availability of the GPS signal from the U.S.

  • Page 3: Table Of Contents

    PowerGlide Plus Kit Contents ....................5 Install the PowerGlide Plus Hydraulic System ................. 9 Remove the Orifice Fittings ....................9 Install Fittings on the AutoBoom Valve ................12 Mount the AutoBoom Valve ....................13 Install the Left and Right Cylinder Hoses ................15 PowerGlide Plus Hydraulic Schematic ................
  • Page 4 ......................41 Envizio Plus ........................42 SCS 4000/5000 ......................... 43 Viper Pro & Envizio Pro ..................... 44 Chapter 5 Replacement Parts ............... 45 Valve Blocks ..........................45 Wheels ............................ 46 Sensors ........................... 46 GVM Predator (2007 & Older) AutoBoom Installation Manual...

  • Page 5: Important Safety Information

    Raven dealer for support. • Follow all safety labels affixed to the AutoBoom system components. Be sure to keep safety labels in good condition and replace any missing or damaged labels. To obtain replacements for missing or damaged safety labels, contact your local Raven dealer.

  • Page 6: Hydraulic Safety

    Chapter 1 WARNING • When starting the machine for the first time after installing AutoBoom, be sure that all persons stand clear, in case a hose has not been properly tightened. • The machine must remain stationary and switched off, with the booms unfolded and supported while installation or maintenance is conducted.

  • Page 7: Chapter 2 Introduction

    C h a p t e r 2 Introduction Congratulations on your purchase of the Raven AutoBoom system! This system is designed to provide automated boom height adjustment for agricultural equipment. This manual applies to the following machines. For future reference, write your serial number in the space below.

  • Page 8: Recommendations

    Set of tools Preparing for Installation Before installing AutoBoom, park the machine where the ground is level, clean, and dry. Leave the machine turned off for the duration of the installation process. During the installation process, follow good safety practices. Be sure to carefully read the instructions in this manual as you complete the installation process.

  • Page 9: Powerglide Plus

    PowerGlide Plus Kit Contents This section contains a list of the components that are included in the PowerGlide Plus AutoBoom kit. Before beginning the AutoBoom installation, compare the items in the AutoBoom kit with the components on this list. If you have questions about the kit, contact your Raven dealer.
  • Page 10 Fitting - 9/16” JIC (M) TO 3/4” SAE O-Ring 333-0012-046 (M) Straight Adapter Fitting - 9/16” JIC (M) TO 7/16” SAE O-Ring 333-0012-050 (M) Straight Adapter Fitting - 11/16” Hex to 9/16” SAE O-Ring Plug 333-0012-194 GVM Predator (2007 & Older) AutoBoom Installation Manual...
  • Page 11 (F) 90° - 12” PowerGlide Plus Wheel Kit (P/N 117-0133-050) TABLE 3. Picture Item Description Part Number Qty. Axle Assembly - Right Cushioned AutoBoom 063-0131-585 Axle Assembly - Left Cushioned AutoBoom 063-0131-590 Bracket - GVM Predator Wheel 116-0159-586 Wheel 322-0131-008 U-Bolt - 2-1/16”...
  • Page 12 TABLE 4. Picture Item Description Part Number Qty. CAN AutoBoom Calibration & Operation Not Pictured 016-0130-062 Manual Node - PowerGlide Plus AutoBoom 063-0130-010 Cable - Harness 115-0230-045 Cable - Power/CAN Controller 115-0230-007 GVM Predator (2007 & Older) AutoBoom Installation Manual...

  • Page 13: Install The Powerglide Plus Hydraulic System

    Remove the Orifice Fittings Before populating the hydraulic fittings on the AutoBoom valve, it is necessary to remove orifice fittings from the valve in the PowerGlide Plus system. Failure to remove these fittings from the valve will restrict the down speed of the booms when the system is enabled.
  • Page 14 FIGURE 1. Port 3B Port 3A Locate Ports 3A and 3B on the AutoBoom valve (P/N 063-0131-125). Coil Removed from the AutoBoom Valve FIGURE 2. Remove the coils from the solenoids near Ports 3A and 3B to gain easy access to those ports.
  • Page 15 Port Plug Reinstalled on the AutoBoom Valve FIGURE 5. Use the Allen wrench to reinstall the port plugs on Ports 3A and 3B of the AutoBoom valve. Coil Reinstalled on the AutoBoom Valve FIGURE 6.

  • Page 16: Install Fittings On The Autoboom Valve

    Install Fittings on the AutoBoom Valve Before mounting the AutoBoom valve on the machine, install the proper fittings on the valve. This prepares the valve for installation and simplifies the hose connection process later in the procedure. Refer to the following table to install the fittings in the appropriate ports of the AutoBoom valve.

  • Page 17: Mount The Autoboom Valve

    AutoBoom Valve Mounted on the Valve Mounting Plate FIGURE 7. Secure the AutoBoom valve (P/N 063-0131-125) to the mounting plate (P/N 107-0171-802) using four 5/16”-18 x 7/8” hex bolts (P/N 311-0052-104) and four 5/16” zinc lock washers (P/N 313-1000-019). AutoBoom Valve Mounted on the Machine FIGURE 8.
  • Page 18 Install the straight end of the supplied hydraulic hose (P/N 214-1000-389) on the 90° end of the installed tee fitting. Connect the 90° end of the installed hydraulic hose to the installed fitting in the Left T Port of the AutoBoom valve.

  • Page 19: Install The Left And Right Cylinder Hoses

    Install the male end of the supplied hydraulic hose (P/N 214-1000-390) on the end of the tee fitting from which the accumulator was removed. Connect the other end of the installed hydraulic hose to the installed fittings in Port LC of the AutoBoom valve.

  • Page 20: Powerglide Plus Hydraulic Schematic

    Chapter 3 PowerGlide Plus Hydraulic Schematic GVM Predator (2007 & Older) AutoBoom Installation Manual...

  • Page 21: Install The Gauge Wheels

    PowerGlide Plus Install the Gauge Wheels Gauge Wheel Mounting Location Wheel mounting locations may be influenced by the boom configuration. Determine the appropriate location for mounting the wheels on the boom, ensuring the wheels will not interfere with or be damaged while folding or unfolding the booms.

  • Page 22: Install The Powerglide Plus Wiring

    AutoBoom Node Installed FIGURE 12. Mount the AutoBoom node (P/N 016-0130-010) inside the node mounting enclosure (if available) or on the AutoBoom valve mounting plate (P/N 107-0171-802) using three 3/8”-16 x 1-1/4” zinc hex bolts (P/N 311- 0054-106) and three 3/8”-16 zinc flanged lock nuts (P/N 312-1001-164).

  • Page 23: Connect The Harness Cable To The Boom Function Controls

    Install the weatherpack boom sense adapter cables (P/N 115-0230-558) between the machine's cylinder up coils and the connectors. Connect the Cable Up connectors on the AutoBoom harness to the installed boom sense adapter cables. Note: The system will now disengage when Up is pressed on the machine’s controller. The system must be engaged via the AutoBoom controller or field computer screen.

  • Page 24: Connect The Harness Cable To The Controller Cable

    Route the controller cable (P/N 115-0230-007) into the right side of the machine’s cab. Locate the two controller connectors and connect them to the AutoBoom controller. Note: The AutoBoom controller should be mounted in the machine’s cab so that the operator has easy access to it. Connect the Field Computer (If Applicable) Refer to the Installation&...

  • Page 25: Powerglide Plus Wiring Schematics

    PowerGlide Plus PowerGlide Plus Wiring Schematics AutoBoom Controller Manual No. 016-0230-050...

  • Page 26: Envizio Plus

    Chapter 3 Envizio Plus GVM Predator (2007 & Older) AutoBoom Installation Manual...

  • Page 27: Scs 4000/5000

    PowerGlide Plus SCS 4000/5000 Manual No. 016-0230-050...

  • Page 28: Viper Pro & Envizio Pro

    Chapter 3 Viper Pro & Envizio Pro GVM Predator (2007 & Older) AutoBoom Installation Manual...

  • Page 29: Ultraglide

    C h a p t e r 4 UltraGlide Kit Contents This section contains a list of the components that are included in the PowerGlide Plus AutoBoom kit, Before beginning the AutoBoom installation, compare the items in the AutoBoom kit with the components on this list. If you have questions about the kit, contact your Raven dealer.
  • Page 30 Washer - 5/16” Zinc Plated Lock 313-1000-019 Hydraulic Kit (P/N 117-0134-050) TABLE 2. Picture Item Description Part Number Qty. Fitting - 9/16” JIC M/F 90° Swivel Elbow 333-0012-042 Fitting - 9/16” JIC M/M/F Swivel Run Tee 333-0012-043 GVM Predator (2007 & Older) AutoBoom Installation Manual...
  • Page 31 Hydraulic Hose - 9/16” JIC (F) to 9/16” JIC 214-1000-644 (F) 90° - 12” Optional Wheel Kit (P/N 117-0133-050) TABLE 3. Picture Item Description Part Number Qty. Axle Assembly - Right Cushioned AutoBoom 063-0131-585 Axle Assembly - Left Cushioned AutoBoom 063-0131-590 Manual No. 016-0230-050...
  • Page 32 312-1001-164 UltraGlide Wiring Kit (P/N 117-0137-024) TABLE 4. Picture Item Description Part Number Qty. CAN AutoBoom Calibration & Operation Not Pictured 016-0130-062 Manual Node - UltraGlide AutoBoom 063-0130-013 Cable - Sensor 115-0171-527 GVM Predator (2007 & Older) AutoBoom Installation Manual...

  • Page 33: Install The Ultraglide Hydraulic System

    AutoBoom hydraulic valve. NOTICE The appearance of the AutoBoom hydraulic valve may vary slightly from the images contained in this manual. However, the fittings, hose connections, and cable connections remain the same.

  • Page 34: Install Fittings On The Autoboom Valve

    Install Fittings on the AutoBoom Valve Before mounting the AutoBoom valve on the machine, install the proper fittings on the valve. This prepares the valve for installation and simplifies the hose connection process later in the procedure. Refer to the following table to install the fittings in the appropriate ports of the AutoBoom valve.

  • Page 35: Mount The Autoboom Valve

    AutoBoom Valve Mounted on the Valve Mounting Plate FIGURE 1. Secure the AutoBoom valve (P/N 063-0131-125) to the mounting plate (P/N 107-0171-802) using four 5/16”-18 x 7/8” hex bolts (P/N 311-0052-104) and four 5/16” zinc lock washers (P/N 313-1000-019). AutoBoom Valve Mounted on the Machine FIGURE 2.
  • Page 36 Install the straight end of the supplied hydraulic hose (P/N 214-1000-389) on the 90° end of the installed tee fitting. Connect the 90° end of the installed hydraulic hose to the installed fitting in the Left T Port of the AutoBoom valve.

  • Page 37: Install The Left And Right Cylinder Hoses

    Install the male end of the supplied hydraulic hose (P/N 214-1000-390) on the end of the tee fitting from which the accumulator was removed. Connect the other end of the installed hydraulic hose to the installed fittings in Port LC of the AutoBoom valve.

  • Page 38: Ultraglide Hydraulic Schematic

    Chapter 4 UltraGlide Hydraulic Schematic GVM Predator (2007 & Older) AutoBoom Installation Manual...

  • Page 39: Install The Ultraglide Sensors

    UltraGlide Install the UltraGlide Sensors Boom Sensor Mounting Locations Sensor mounting locations may be influenced by the boom configuration. Determine the appropriate location for mounting the sensors on the boom, ensuring the sensors will not interfere with or be damages while folding or unfolding the booms.

  • Page 40: Mount The Center Rack Sensor

    Loop and tie-off any excess cabling, allowing enough cable for boom folding and extension. Repeat the steps above to connect the remaining sensor cable(s). Note: The sensor cables will be connected to the AutoBoom system in the wiring phase of installation. GVM Predator (2007 & Older) AutoBoom Installation Manual...

  • Page 41: Install The Gauge Wheels - Optional

    UltraGlide Install the Gauge Wheels - Optional Gauge Wheel Mounting Location Wheel mounting locations may be influenced by the boom configuration. Determine the appropriate location for mounting the wheels on the boom, ensuring the wheels will not interfere with or be damaged while folding or unfolding the booms.

  • Page 42: Install The Ultraglide Wiring

    AutoBoom Node Installed FIGURE 8. Mount the AutoBoom node (P/N 016-0130-013) inside the node mounting enclosure (if available) or on the AutoBoom valve mounting plate (P/N 107-0171-802) using three 3/8”-16 x 1-1/4” zinc hex bolts (P/N 311- 0054-106) and three 3/8”-16 zinc flanged lock nuts (P/N 312-1001-164).

  • Page 43: Connect The Harness Cable To The Boom Function Controls

    Install the weatherpack boom sense adapter cables (P/N 115-0230-558) between the machine's cylinder up coils and the connectors. Connect the Cable Up connectors on the AutoBoom harness to the installed boom sense adapter cables. Note: The system will now disengage when Up is pressed on the machine’s controller. The system must be engaged via the AutoBoom controller or field computer screen.

  • Page 44: Connect The Harness Cable To The Sensors

    Route the controller cable (P/N 115-0230-007) into the right side of the machine’s cab. Locate the two controller connectors and connect them to the AutoBoom controller. Note: The AutoBoom controller should be mounted in the machine’s cab so that the operator has easy access to it. Connect the Field Computer (If Applicable) Refer to the Installation&...

  • Page 45: Ultraglide Wiring Schematics

    UltraGlide UltraGlide Wiring Schematics AutoBoom Controller Manual No. 016-0230-050...

  • Page 46: Envizio Plus

    Chapter 4 Envizio Plus GVM Predator (2007 & Older) AutoBoom Installation Manual...

  • Page 47: Scs 4000/5000

    UltraGlide SCS 4000/5000 Manual No. 016-0230-050...

  • Page 48: Viper Pro & Envizio Pro

    Chapter 4 Viper Pro & Envizio Pro GVM Predator (2007 & Older) AutoBoom Installation Manual...

  • Page 49: Replacement Parts

    R eplacement Parts CHAPTER C h a p t e r 5 This section contains replacement part diagrams for PowerGlide Plus and UltraGlide system. Refer to these diagrams when calling to request replacement parts. Valve Blocks Manual No. 016-0230-050...

  • Page 50: Wheels

    Chapter 5 Wheels Sensors GVM Predator (2007 & Older) AutoBoom Installation Manual...
  • Page 51 Safety 2 Tools Needed Hydraulic Fittings 4 Safety 2 UltraGlide Hydraulic System Installing Fittings on the AutoBoom Valve 30 Important Safety Information Installing Fittings on the Logic Valve 30 Electrical 2 Mounting the AutoBoom Valve 31 Hydraulics 2 Install Gauge Wheel...
  • Page 52 Index GVM Predator (2007 & Older) AutoBoom Installation Manual...
  • Page 53 How Can I Get Service? Bring the defective part and proof of purchase to your Raven Dealer. If your Dealer agrees with the warranty claim, the Dealer will send the part and proof of purchase to their distributor or to Raven Industries for final approval.
  • Page 54 P.O. Box 5107 Fax: 605-331-0426 Sioux Falls, SD 57117-5107 www.ravenprecision.com atdinfo@ravenind.com Notice: This document and the information provided are the property of Raven Industries, Inc. and may only be used as authorized by Raven Industries, Inc. All rights reserved under copyright laws.

Table of Contents