Dremel STYLO+ 2050 Original Instructions Manual page 9

side forces applied to these wheels may cause them to
shatter.
b. For threaded abrasive cones and plugs use only
undamaged wheel mandrels with an unrelieved
shoulder flange that are of correct size and length.
Proper mandrels will reduce the possibility of breakage.
c. Do not "jam" a cut-off wheel or apply excessive
pressure. Do not attempt to make an excessive depth
of cut. Overstressing the wheel increases the loading and
t
susceptibility to twisting or snagging of the wheel in the cut
and the possibility of kickback or wheel breakage.
d. Do not position your hand in line with and behind the
rotating wheel. When the wheel, at the point of operation,
is moving away from your hand, the possible kickback may
propel the spinning wheel and the power tool directly at
you.
e. When wheel is pinched, snagged or when interrupting
a cut for any reason, switch off the power tool and
hold the power tool motionless until the wheel comes
to a complete stop. Never attempt to remove the cut-off
wheel from the cut while the wheel is in motion otherwise
kickback may occur. Investigate and take corrective action
to eliminate the cause of wheel pinching or snagging.
f. Do not restart the cutting operation in the workpiece.
Let the wheel reach full speed and carefully re-enter the
cut. The wheel may bind, walk up or kickback if the power
tool is restarted in the workpiece.
g. Support panels or any oversized workpiece to minimize
the risk of wheel pinching and kickback. Large
workpieces tend to sag under their own weight. Supports
must be placed under the workpiece near the line of cut
and near the edge of the workpiece on both sides of the
wheel.
h. Use extra caution when making a "pocket cut" into
existing walls or other blind areas. The protruding wheel
may cut gas or water pipes, electrical wiring or objects that
can cause kickback.
SAFETY WARNINGS SPECIFIC FOR
a. Be aware that wire bristles are thrown by the brush
even during ordinary operation. Do not overstress the
wires by applying excessive load to the brush. The wire
bristles can easily penetrate light clothing and/or skin.
b. Allow brushes to run at operating speed for at least one
minute before using them. During this time no one is to
stand in front or in line with the brush. Loose bristles or
wires will be discharged during the run-in time.
c. Direct the discharge of the spinning wire brush away
from you. Small particles and tiny wire fragments may be
discharged at high velocity during the use of these brushes
and may become imbedded in your skin.
d. Do not exceed 15,000 RPM when using wire brushes.
WARNING
!
CONSIDERED CARCINOGENIC).
WARNING
!
THAT IS HARMFUL TO ONE'S HEALTH, COMBUSTIBLE OR
EXPLOSIVE (SOME DUSTS ARE CONSIDERED
CARCINOGENIC); WEAR A DUST MASK AND WORK WITH
DUST/CHIP EXTRACTION WHEN CONNECTABLE.
The machine, accessories and packaging should be sorted for
environmental-friendly recycling.
WIRE BRUSHING OPERATIONS
DO NOT WORK WITH MATERIALS
CONTAINING ASBESTOS (ASBESTOS IS
TAKE PROTECTIVE MEASURES WHEN
DURING WORK DUST CAN DEVELOP
ENVIRONMENT
DISPOSAL
ONLY FOR EUROPEAN COUNTRIES
Do not dispose of power tools into household waste!
According the European Guideline 2012/19/EC for
Waste Electrical and Electronic Equipment and its
implementation into national right, power tools that are
no longer usable must be collected separately and
disposed of in an environmentally correct manner.
SPECIFICATIONS
GENERAL SPECIFICATIONS
Model no 2050
Voltage Rating 100-240V~ 50-60Hz, 18Vdc, 0.5A
Max. Speed 22,000/min
Chuck Capacity 0.8mm - 3.2mm
Maximum diameter
of Accessory 31.8mm
Power supply 2610Z09729 (EU)
2610Z09734 (UK)
EXTENSION CORDS
Use completely unrolled and safe extension cords with a
capacity of 5A.
ASSEMBLY
ALWAYS UNPLUG ROTARY TOOL
WARNING
!
BEFORE CHANGING ACCESSORIES,
CHANGING COLLETS OR SERVICING
YOUR ROTARY TOOL.
PICTURE 1
A. On/Off button
B. Variable Speed Dial
C. Ventilation Openings
D. Shaft Lock Button
E. Dremel Chuck
F. DC Jack
G. DC Socket
H. Power Adapter
DREMEL CHUCK
Dremel Chuck allows you to quickly and easily change
accessories on Dremel Rotary Tools without changing collets.
Accepts accessories with 1/32" - 1/8" shank. To loosen, first
press shaft lock button and rotate the shaft by hand until the
lock engages the shaft preventing further rotation.
DO NOT ENGAGE LOCK WHILE THE
WARNING
!
ROTARY TOOL IS RUNNING.
With the shaft lock engaged use the wrench to loosen the
chuck and open the jaws. Remove the accessory from the
chuck. If necessary, continue loosening the chuck so that the
new accessory fits between the jaws. Insert the new accessory
into the chuck far enough so that there is approximately 1/4"
between the end of the chuck and the beginning of the working
part of the accessory (drill bit flutes, sand paper, engraving end,
etc.). With the shaft lock engaged, tighten the chuck using the
wrench to secure the accessory.
HELPFUL TIPS WHEN USING THE DREMEL CHUCK
• The Dremel Chuck and the collet and collet nut system are
interchangeable on this tool. While the chuck will provide
you with the best experience for changing accessories, the
collet and collet nut will provide a more precise accessory
9