Page 2
DM 2610004477 08-09:DM 2610004477 08-09 8/3/09 1:18 PM Page 2 Power Tool Safety Rules Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS Work Area When operating a power tool outside, use an outdoor extension cord marked "W-A"...
Page 3
DM 2610004477 08-09:DM 2610004477 08-09 8/3/09 1:18 PM Page 3 job better and safer at the rate for which it is serviced before using. Many accidents are designed. caused by poorly maintained tools. Develop a periodic maintenance schedule for your tool. Do not use tool if switch does not turn it “ON”...
Page 4
DM 2610004477 08-09:DM 2610004477 08-09 8/3/09 1:18 PM Page 4 Safety Rules for Rotary Tools - (cont.) Allow brushes to run at operating speed in the workpiece. Nails or foreign objects can for at least one minute before using wheel. cause the bit to jump.
Page 5
DM 2610004477 08-09:DM 2610004477 08-09 8/3/09 1:18 PM Page 5 applications. Serious personal injury may Some dust created by result. power sanding, sawing, grinding, drilling, and other construction When using the steel saws, cutoff wheels, activities contains chemicals known to high speed cutters or tungsten carbide cause cancer, birth defects or other cutters, always have the work securely...
Page 6
DM 2610004477 08-09:DM 2610004477 08-09 8/3/09 1:18 PM Page 6 Symbols IMPORTANT: Some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.
Page 7
DM 2610004477 08-09:DM 2610004477 08-09 8/3/09 1:18 PM Page 7 Functional Description and Specifications Disconnect the plug from the power source before making any assembly, adjustments or changing accessories. Such preventive safety measures reduce the risk of starting the tool accidentally. Models 100 &...
Page 8
DM 2610004477 08-09:DM 2610004477 08-09 8/3/09 1:18 PM Page 8 Assembly Always unplug Rotary Tool COLLET IDENTIFICATION CHART before changing accessories, Collet sizes can be identified by the rings on changing collets or servicing your Rotary the back end of collet. Tool.
To learn about more uses and the Instead, lower the spinning accessory lightly to versatility of Dremel accessories and attachments refer to this Owner's Manual or the work and allow it to touch the point at which you want cutting (or sanding or etching, check our website at www.Dremel.com.
With it, you have the best control, are efficient work out of the accessory. Questions or Problems? Call 1-800-437-3635 or check our website at www.Dremel.com For best control in close work, grip the The “Golf Grip” method of holding the...
Page 11
Leaning on the tool does not help. Hardwoods, metals and glass require high Let speed do the work! speed operation, and drilling should also be done at high speeds. Use only Dremel ® , high-performance accessories.
Page 12
(Figure D). performed by unauthorized personnel may result in misplacing of internal wires and components which could cause serious hazard. We recommend that all tool service be performed by a Dremel Service Facility. avoid injury from unexpected starting or...
Page 13
— and a variety of sizes and shapes 1/16" collets accommodate all of the avail - within each category which enables you to get able Dremel accessories. 1/8" collets are the perfect accessory for every need. included in most rotary tool kits.
Page 14
This is a screw mandrel used with the felt polishing tip and felt polishing wheels. 1/8" shank. EZ Lock Mandrel N° 402 The Dremel EZ Lock makes accessory changes easy as PULL - TWIST - RELEASE. Small Screw Mandrel N° 402 The one-piece mandrel design simplifies the...
Page 15
DM 2610004477 08-09:DM 2610004477 08-09 8/3/09 1:18 PM Page 15 Dremel Accessories (Cont.) 3. Apply the brush to the work in such a way that as much of the brush face as possible is in full contact with the work. Applying the side or edge of the brush to the work will result in wire breakage and shortened brush life.
Page 16
Do not exceed 15,000 RPM in speed. 1/8" shank. High Speed Router Bits For routing, inlaying, and mortising in wood and other soft materials. Use with Dremel No. 335 Router attachment and No. 231 Shaper/Router table. Grinding Wheel Use for deburring, removing rust, and general purpose grinding.
Page 17
DM 2610004477 08-09:DM 2610004477 08-09 8/3/09 1:18 PM Page 17 Speed Settings * Speed for light cuts; Caution - burning on deep grooves. • Depending on cutting direction relative to grain. Not all speed settings can be achieved on 100 and 200 series tool. For certain applications, a variable speed tool is required.
Page 18
DM 2610004477 08-09:DM 2610004477 08-09 8/3/09 1:18 PM Page 18 Speed Settings (Continued) * Speed for light cuts; Caution - burning on deep grooves. • Depending on cutting direction relative to grain. Not all speed settings can be achieved on 100 and 200 series tool. For certain applications, a variable speed tool is required.
Page 19
DM 2610004477 08-09:DM 2610004477 08-09 8/3/09 1:18 PM Page 19 Speed Settings (Continued) * Speed for light cuts; Caution - burning on deep grooves. • Depending on cutting direction relative to grain. Not all speed settings can be achieved on 100 and 200 series tool. For certain applications, a variable speed tool is required.
Page 20
DM 2610004477 08-09:DM 2610004477 08-09 8/3/09 1:18 PM Page 20 Speed Settings (Continued) * Speed for light cuts; Caution - burning on deep grooves. • Depending on cutting direction relative to grain. Not all speed settings can be achieved on 100 and 200 series tool. For certain applications, a variable speed tool is required.