1. Manuals
  2. Brands
  3. NEC Manuals
  4. Telephone System
  5. SL1100
  6. Hardware manual

NEC SL1100 Hardware Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
Table of Contents
Hardware Manual
A50-031693-004 AU
ISSUE 1.0 (R2.0)
July 2012

Advertisement

Table of Contents
loading

  Also See for NEC SL1100

NEC SL1100 Features And Specifications Manual
NEC SL1100 Features And Specifications Manual 864 pages
NEC SL1000 Features And Specifications Manual
NEC SL1000 Features And Specifications Manual 814 pages
NEC SL 1000 Programming Manual
NEC SL 1000 Programming Manual 666 pages

  Related Manuals for NEC SL1100

  Summary of Contents for NEC SL1100

  • Page 1 Hardware Manual A50-031693-004 AU ISSUE 1.0 (R2.0) July 2012...
  • Page 2 Copyright NEC shall not be liable for any direct, indirect, consequential or incidental damages about the use of this equipment, manual or any related materials. NEC Corporation reserves the right to change the specifications, functions, or features at any time without notice.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS Chapter1 Introduction 1-1 SECTION 1 GENERAL INFORMATION SECTION 2 EQUIPMENT LIST 2.1 KSUs and Optional Unit 2.1.1 IP4[ ]-1228M-B KSU 2.1.2 IP4WW-Battery Box 2.2 Trunk/Extension/ISDN Expansion Interface Cards 2.2.1 IP4WW-080E-B1 2.2.2 IP4[ ]-008E-B1 2.2.3 IP4WW-000E-B1 2.2.4 IP4WW-4COIDB-B1 2.2.5 IP4WW-2BRIDB-C1 2.2.6 IP4WW-1PRIU-C1 2.3 Optional Interface Cards...
  • Page 4 TABLE OF CONTENTS 1.4.3 AC Power Cord 1.5 Trunk/Extension Cabling 1.5.1 General 1.5.2 Precautions for Cabling 1.5.3 Trunk Cabling 1.5.4 Extension Cabling 1.5.5 Cable Routing and Clamping 2-11 SECTION 2 INSTALLING THE EXTERNAL BACKUP BATTERY 2-12 2.1 General 2-12 2.2 Unpacking 2-12 2.3 Battery Box Dimensions 2-13...
  • Page 5 TABLE OF CONTENTS 4.3.2 Unpacking 2-58 4.3.3 Installing the PZ-VM21 PCB 2-58 4.4 Installing the CF Card (CFVMS) 2-61 SECTION 5 INSTALLING THE MULTILINE TELEPHONES AND OPTIONAL TERMINALS 2-63 5.1 Installing the Multiline Telephones 2-63 5.1.1 Location of Controls 2-63 5.1.2 Multiline Telephone Legs Adjustment 2-64 5.1.3 Wall-Mounting the Multiline Telephone...
  • Page 6 TABLE OF CONTENTS Chapter4 Maintenance SECTION 1 FUSE REPLACEMENT 1.1 Replacing the Fuse SECTION 2 LITHIUM BATTERY REPLACEMENT 2.1 General 2.2 Lithium Battery Specification 2.3 Replacing the Lithium Battery SECTION 3 MAIN SOFTWARE UPGRADING 3.1 General 3.2 Before Upgrading the Main Software 3.3 Main Software Version Confirmation 3.4 Upgrading the Main Software SECTION 4 LED INDICATIONS...
  • Page 7 LIST OF TABLES Table 1-1 Memory Capacity of MEMDB-C1 .................1-5 Table 1-2 System Capacity....................1-8 Table 2-1 KSU Packing List....................2-2 Table 2-2 Items on the CPU card ..................2-2 Table 2-3 Power Requirement....................2-7 Table 2-4 RJ61 Cable Connector Pin-Outs (J101-J103) ............2-11 Table 2-5 IP4WW-Battery Box Packing List ...............2-12 Table 2-6 Battery Specifications ..................2-13 Table 2-7 Expansion Cards ....................2-33 Table 2-8 Expansion Card Packing List................2-33...
  • Page 8 LIST OF FIGURES Figure 1-1 System Configuration..................1-1 Figure 1-2 System Image .....................1-9 Figure 1-3 Maximum KSU Capacity - Expandability of Trunk and Extension (without PRI) .1-9 Figure 1-4 Maximum KSU Capacity - Expandability of Trunk and Extension (with PRI) ..1-10 Figure 2-1 CPU Card Location .....................2-2 Figure 2-2 Dimension of the Main KSU................2-3 Figure 2-3 Wall Mount of KSU....................2-4...
  • Page 9 LIST OF FIGURES Figure 2-48 Replacing the Fuse ..................2-31 Figure 2-49 Install the Fuse Unit ..................2-31 Figure 2-50 Securing the Fuse Unit ...................2-31 Figure 2-51 Connect Battery Connection Cable..............2-32 Figure 2-52 Installation of the Front Cover .................2-32 Figure 2-53 Removing the Sub-Cover................2-34 Figure 2-54 Removing the Main-Cover ................2-34 Figure 2-55 Mounting the 1st Expansion Interface Card ............2-35 Figure 2-56 Mounting the 2nd Expansion Interface Card...........2-36...
  • Page 10 LIST OF FIGURES Figure 2-100 Leg Setting for High Position ................2-66 Figure 2-101 Cabling for Wall-Mount..................2-66 Figure 2-102 Wall-Mount Unit - 24TIXH-C .................2-67 Figure 2-103 Hook-Switch Hanger ..................2-67 Figure 2-104 Wall-Mount Screw Guide ................2-68 Figure 2-105 Mounting the Multiline Telephone ..............2-68 Figure 2-106 IP Multiline Telephone Connection..............2-69 Figure 2-107 IP Multiline Telephone Connectors..............2-69 Figure 2-108 Low Position Setting ..................2-70...
  • Page 11 LIST OF FIGURES Figure 4-14 Display of Multiline Telephone ................4-8 Figure 4-15 Removing the Sub-Cover..................4-9 Figure 4-16 Removing the Main-Cover ................4-10 Figure 4-17 Inserting the CF card ..................4-10 Figure 4-18 LOAD Button (S1) Location ................4-10 Figure 4-19 Removing the CF card ..................4-11 Hardware Manual...
  • Page 13 ISSUE 1.0 SL1100 Regulatory BATTERY DISPOSAL The SL1100 system includes the batteries listed below. When disposing of these batteries, KSU, and/or Unit, you must comply with applicable regulations relating to your location regarding proper disposal procedures. Unit Name Type of Battery...
  • Page 14 This equipment must only be installed and maintained by service personnel. In the event of equipment malfunction, all repairs must be performed by an authorised dealer of NEC. It is the responsibility of users requiring service to report the need for service to one of NEC authorised...

  • Page 15: Chapter1 Introduction

    The small compact KSU comes with an installed CPU and eight digital and four analogue extension ports and has two stackable slots for further expansion. The SL1100 provides a maximum of 12 analogue trunks and 24 Multiline terminals, and also equipped to support Digital Network (BRI/PRI) and IP Trunks (SIP) or IP extensions.

  • Page 16: Section 2 Equipment List

    SL1100 ISSUE 1.0 SECTION 2 EQUIPMENT LIST The following table lists all equipment for the SL1100 system. Stock Number Equipment Name Equipment Description Note 8503498 SL1100 TDM Basic Kit SL1100 TDM Basic Kit (For AT) <Including> IP4AT-1228M-B KSU, PZ-VM21, IP4WW-CFVMS-C1, IP4WW-12TXH-B-TEL (BK) (3 sets)

  • Page 17: Ksus And Optional Unit

    ISSUE 1.0 SL1100 KSUs and Optional Unit 2.1.1 IP4[ ]-1228M-B KSU The Main or controlling KSU is shipped fully assembled. The following are included with the KSU: CPU with main software (CPU-B1)  Power supply (110V/240V)  1 External backup battery connector ...

  • Page 18: Ip4[ ]-008E-B1

    SL1100 ISSUE 1.0 2.2.2 IP4[ ]-008E-B1 This 008E card is installed in the 1228M KSU and provides a total of eight analogue ports. Either the analogue trunk daughter board (4COIDB) or the ISDN BRI daughter board (2BRIDB) can be mounted on this card.

  • Page 19: Optional Interface Cards

    ISSUE 1.0 SL1100 Optional Interface Cards 2.3.1 IP4[ ]-MEMDB-C1 This card provides additional expansion memory. Following memories are equipped on this card. Table 1-1 Memory Capacity of MEMDB-C1 Memory Type Capacity SDRAM 64 MB Flash Memory 32 MB The MEMDB is mounted on the CPU card and provides the...

  • Page 20: Multiline Telephones And Optional Equipment

    SL1100 ISSUE 1.0 Multiline Telephones and Optional Equipment 2.4.1 IP4WW-12TXH-B TEL The 12TXH-B TEL is a 2-wire digital multiline telephone featuring: Programmable keys: 12  Soft Keys: 4  LCD: 24 digits x 3 lines with Backlit  Handsfree: Full-duplex ...

  • Page 21: Ip4Ww-60D Dss-B

    ISSUE 1.0 SL1100 2.4.4 IP4WW-60D DSS-B The DSS console gives a multiline terminal user a Busy Lamp Field (BLF) and one-button access to extensions, trunks and system features. Mainly designed for operator use, the 60-button DSS console provides an additional 60 programmable keys.

  • Page 22: Table 1-2 System Capacity

    SL1100 ISSUE 1.0 SECTION 3 SYSTEM CAPACITY System Capacity Table 1-2 System Capacity Items 1 KSU (1228) Description Note Expansion Slot System Maximum Port 1KSU: 084M+PRI+080E+4COIDBx2 Trunk Port Max. 1KSU: PRIx1+4COIDB/BRIx2 Trunk Port Analogue Trunks 1KSU: 4COIDBx3 on (COT) 084M/080E/008E/000E...

  • Page 23: Ksu Capacity

    ISSUE 1.0 SL1100 KSU Capacity System image of KSU capacity (ISDN, Trunk, Extension) is shown as below. Figure 1-2 System Image 3.2.1 Expandability of Trunk and Extension (without PRI) Figure 1-3 Maximum KSU Capacity - Expandability of Trunk and Extension (without PRI)

  • Page 24: Expandability Of Trunk And Extension (With Pri)

    SL1100 ISSUE 1.0 3.2.2 Expandability of Trunk and Extension (with PRI) Figure 1-4 Maximum KSU Capacity - Expandability of Trunk and Extension (with PRI) 1-10 Introduction...

  • Page 25: Chapter2 Installation

    Installation SECTION 1 INSTALLING THE MAIN KSU Before Installing the KSU 1.1.1 General Precautions To avoid shock or equipment damage, do not plug in or turn the system power on before  completing the installation process. Avoid working with the Equipment during electrical storms. ...

  • Page 26: Unpacking

    SL1100 ISSUE 1.0 1.1.5 Unpacking Unpack the KSU and check it against the following list. Inspect for physical damage. Table 2-1 KSU Packing List Items List of Contents 1228M-B KSU 1228M-B KSU AC Power Cord Screws (M4.1x25) Wall-Mounting Template End User License Agreement (EULA)

  • Page 27: Wall-Mounting The Ksu

    ISSUE 1.0 SL1100 Wall-Mounting the KSU 1.3.1 KSU Dimensions For Dimensions of the 1228M-B KSU, refer to Figure 2-2 Dimension of the Main KSU. Figure 2-2 Dimension of the Main KSU 1.3.2 Wall Installation of KSU The Main KSU (1228M-B) can be mounted on the wall. Before installing, ensure the appropriate spacing exists as shown below.

  • Page 28: Mounting Procedure Of Ksu

    SL1100 ISSUE 1.0 Figure 2-3 Wall Mount of KSU In the case, the KSU is mounted on Battery Box, refer to 2.6.2 Wall-Mounting the IP4WW-Battery Box. 1.3.3 Mounting Procedure of KSU One Main KSU can be mounted per IP4WW-Battery Box. For the mounting, refer to 2.6.3 Mounting One KSU on the Battery Box.

  • Page 29: Figure 2-5 Screw Positions

    ISSUE 1.0 SL1100 Install four screws into the wall. The screw heads must stand off from the wall about 2.5 mm (0.098″) to 3.5 mm (0.138″). Figure 2-5 Screw Positions Wall-Mounting Screws (M4.1x 25: 4 pcs) are attached to the KSU.

  • Page 30: Grounding And Ac Cabling

    SL1100 ISSUE 1.0 The Sub-Cover can be opened and held in the open position.  Figure 2-8 Sub-Cover Open Position Align the four holes on the back of the KSU with the four screws installed in the wall. Figure 2-9 Mounting the KSU Slide the KSU into position and tighten the lower two screws.

  • Page 31: Ac Power Requirement

    ISSUE 1.0 SL1100 Figure 2-10 ETH Lug The grounding cable is supplier-provided.(not attached to the system)  Loosen the screw. Insert a grounding wire (user supplied). Tighten the screw. Connect the grounding wire to earth ground. Proper grounding is very important to protect the system from external noise and to reduce the risk of electrocution in the event of a lightning strike.

  • Page 32: Trunk/Extension Cabling

    Aerial distribution wiring is not allowed.  Trunks must be installed with lightning protectors.  Do not install the Topaz Terminal in the SL1100 system, it does not work properly.  1.5.3 Trunk Cabling Trunk cabling is required for the 4COIDB, 2BRIDB or 1PRIU PCBs.

  • Page 33: Extension Cabling

    Before plugging in the Multiline Telephone, DSS Console, Single line Telephone or Doorphone, ensure Main KSU powered off. Only SL1100 terminals (12TXH, 24TXH) may be connected to a SL1100 digital port. Do not connect any other terminal as damage may result. J421...

  • Page 34: Figure 2-13 Analogue Extension Cabling

    SL1100 ISSUE 1.0 J421 J103 J431 J411 J102 J101 SLI 9-12 /DPH 1-2 Port 1 Port 2 Port 3 Port 4 T : Tip R : Ring Modular Cable Max cable length (2-wire, Straight ) 24AWG ( 0.5 mm) 1,125 m...

  • Page 35: Cable Routing And Clamping

    ISSUE 1.0 SL1100 Table 2-4 RJ61 Cable Connector Pin-Outs (J101-J103) Pin No. ESI 1-4 (J101), ESI 5-8 (J102): SLI 9-12/DPH 1-2 (J103): 2-Wire Digital Extension Port Analogue Extension Port Connector (RJ-61) Connector (RJ-61) T4 (Tip for port 4) T4 (Tip for port 4)

  • Page 36: Section 2 Installing The External Backup Battery

    An optional (locally procured), external battery source can be used to provide power during a power failure. One KSU must have own IP4WW-Battery Box. Do not connect the DX2E-32i/NX7E Topaz Battery Box to the SL1100 system. Damage to equipment or property may result.

  • Page 37: Battery Box Dimensions

    ISSUE 1.0 SL1100 Battery Box Dimensions Figure 2-16 Dimension of the IP4WW-Battery Box Battery Specifications Table 2-6 Battery Specifications Item Data Capacity 12 V, 7.0 Am/H or equivalent (Voltage must be 12 V) Recommended Battery GS Yuasa NP7-12 (151 x 65 x 97.5 mm / 2.7 kg) <GS Yuasa International LTD.>...

  • Page 38: Figure 2-17 Removing The Front Cover

    SL1100 ISSUE 1.0 Figure 2-17 Removing the Front Cover Disconnect the Battery Connection Cable from the Fuse Unit if the cable is plugged already. Figure 2-18 Disconnect Battery Connection Cable Loosen the screw and lift the Batt Stopper. 2-14 Installation...

  • Page 39: Figure 2-19 Batt Stopper

    ISSUE 1.0 SL1100 Figure 2-19 Batt Stopper Pull out the Battery tray. Figure 2-20 Pulling out the Battery Tray Loosen two screws and remove the Battery tray cover. Remove two screws and remove the Battery tray bracket. Hardware Manual 2-15...

  • Page 40: Figure 2-21 Remove The Battery Tray Bracket

    SL1100 ISSUE 1.0 Figure 2-21 Remove the Battery Tray Bracket Install two batteries into the Battery tray. Figure 2-22 Battery Installation Connect the battery cables. 2-16 Installation...

  • Page 41: Figure 2-23 Connecting The Battery Cables

    ISSUE 1.0 SL1100 Figure 2-23 Connecting the Battery Cables Incorrect installation of batteries may damage the Fuse Unit or cause possible fire. Insert Battery Connection Cable into the Cable guides as shown in the next diagram. 10. Install the Battery tray cover aligning the three tabs and tightening the two screws.

  • Page 42: Figure 2-25 Inserting The Battery Tray

    SL1100 ISSUE 1.0 11. Insert the Battery tray into the Battery Box. Figure 2-25 Inserting the Battery Tray 12. Set the Batt Stopper bracket in place and secure with screw. Figure 2-26 Secure Batt Stopper Bracket 13. Plug the Battery Connection Cable into the Fuse unit.

  • Page 43: Mounting The Ip4Ww-Battery Box

    ISSUE 1.0 SL1100 Figure 2-27 Connecting the Battery Connection Cable 14. Align tabs a to f to holes A to F on Battery Box. Slide the Front cover and tighten the two screws. Figure 2-28 Installation of Front Cover Mounting the IP4WW-Battery Box The IP4WW-Battery Box can be installed on either the floor or wall.

  • Page 44: Figure 2-29 Bases And Support Of The Battery Box

    SL1100 ISSUE 1.0 Figure 2-29 Bases and Support of the Battery Box Refer to Floor-Mount Spacing Guide for required spacing before drilling holes for 10 mm (0.394″) anchor bolts (locally procured). Mark and drill the four holes required to install the FM/WM Base.

  • Page 45: Wall-Mounting The Ip4Ww-Battery Box

    ISSUE 1.0 SL1100 Figure 2-31 Mounting the Battery Box Using four supplied screws, secure the IP4WW-Battery Box to the FM/WM Base. Figure 2-32 Securing the Battery Box 2.6.2 Wall-Mounting the IP4WW-Battery Box When wall-mounting the IP4WW-Battery Box, ensure the wall can support the weight of the Battery Box (Total weight=17.6 kg (620.75 oz) - Including...

  • Page 46: Figure 2-33 Assemble Battery Box Base

    SL1100 ISSUE 1.0 Plywood should first be installed on the wall where the Battery Box will be positioned. This allows secure anchoring of the screws which support the weight of the Battery Box. Using four supplied screws, secure the WM Support to the FM/WM Base-F and Base-R.

  • Page 47: Figure 2-34 Wall-Mount Spacing Guide

    ISSUE 1.0 SL1100 Figure 2-34 Wall-Mount Spacing Guide Loosen two screws and remove the Front Cover. Hardware Manual 2-23...

  • Page 48: Figure 2-35 Removing The Front Cover

    SL1100 ISSUE 1.0 Figure 2-35 Removing the Front Cover Using the four hooks on the FM/WM Base mount the IP4WW-Battery Box to the Base. Figure 2-36 Mounting the Battery Box Using one supplied screw (M3x6 with washer), secure the back plane of the Battery Box to the FM/WM Base.

  • Page 49: Mounting One Ksu On The Battery Box

    ISSUE 1.0 SL1100 Figure 2-37 Securing the Battery Box 2.6.3 Mounting One KSU on the Battery Box Before wall-mounting or floor-mounting the IP4WW-Battery Box, a single KSU can be mounted on the Battery Box. Loosen two screws and remove the Front Cover of the Battery Box.

  • Page 50: Figure 2-39 Removing The L-Bracket

    SL1100 ISSUE 1.0 Figure 2-39 Removing the L-Bracket Turn the L-Bracket upside down. Rotate the L-Bracket 180 degrees so that the upper FACE as shown in Removing the L-Bracket is located at the bottom as shown in Securing the L-Bracket and WM Hook.

  • Page 51: Figure 2-40 Securing The L-Bracket And Wm Hook

    ISSUE 1.0 SL1100 Figure 2-40 Securing the L-Bracket and WM Hook Install four screws into the L-Bracket (Do not tighten). A space of 2.5 mm (0.098″) to 3.5 mm (0.138″) for KSU mounting is required. Mount the KSU on the screw heads.

  • Page 52: Ip4Ww-Battery Box To Ksu Connection

    ISSUE 1.0 Figure 2-42 KSU Mounting on Battery Box IP4WW-Battery Box to KSU Connection Do not connect the DX2E-32i/NX7E Topaz Battery Box to the SL1100 system. Damage to equipment or property may result. Make sure the system power is off.

  • Page 53: Ip4Ww-Battery Box Fuse Replacement

    ISSUE 1.0 SL1100 Figure 2-44 Connecting Battery Cable Connect Battery cable from the Battery box to Battery connector on the KSU. IP4WW-Battery Box Fuse Replacement In the event of a blown fuse correct the fault causing the fuse to blow before replacing the fuse;...

  • Page 54: Figure 2-45 Removing The Front Cover

    SL1100 ISSUE 1.0 Figure 2-45 Removing the Front Cover Disconnect the Battery connection cable from the Fuse Unit. Figure 2-46 Disconnecting the Battery Connection Cable Loosen the screw from the Fuse Unit. Figure 2-47 Loosen the Fuse Unit Screw 2-30...

  • Page 55: Figure 2-48 Replacing The Fuse

    ISSUE 1.0 SL1100 Slide Fuse Unit out of the Battery box. Replace the fuse (250VT8AL). Figure 2-48 Replacing the Fuse Using the Fuse Unit guides, slide the Fuse Unit into the Battery Box. Figure 2-49 Install the Fuse Unit Secure the Fuse Unit by tightening the screw.

  • Page 56: Figure 2-51 Connect Battery Connection Cable

    SL1100 ISSUE 1.0 Reconnect the Battery Connection Cable to the Fuse Unit. Figure 2-51 Connect Battery Connection Cable 10. Align tabs a to f to holes A to F on Battery Box. Slide the Front Cover into position and tighten the two screws.

  • Page 57: Section 3 Installing The Expansion Interface Cards

    ISSUE 1.0 SL1100 SECTION 3 INSTALLING THE EXPANSION INTERFACE CARDS General Up to two expansion interface cards can be installed per KSU. Table 2-7 Expansion Cards Expansion Interface Description Note Card IP4WW-080E-B1 8 digital extensions card IP4[ ]-008E-B1 8 analogue extensions card...

  • Page 58: Mounting The Expansion Interface Card

    SL1100 ISSUE 1.0 Mounting the Expansion Interface Card DO NOT POWER ON until all installation has been completed. Fit the optional 4COIDB-B1/2BRIDB-C1 daughter boards before installing the 084M-B1/080E-B1/008E-B1/000E-B1 PCBs. Set the switches on the 2BRIDB-C1 board before mounting it onto the 084M-B1/080E-B1/ 008E-B1/000E-B1 PCB.

  • Page 59: Figure 2-55 Mounting The 1St Expansion Interface Card

    ISSUE 1.0 SL1100 Insert two Nylon-spacers into the specified holes, and fasten two Metal-spacers into the specified holes. (Both Nylon and Metal spacers are provided with 080E/008E/000E/1PRIU) If no more Expansion Interface cards are to be mounted on the 1st PCB, fasten two screws to secure the 1st PCB on the top of the 080E/008E/000E/1PRIU.

  • Page 60: Figure 2-56 Mounting The 2Nd Expansion Interface Card

    SL1100 ISSUE 1.0 Figure 2-56 Mounting the 2nd Expansion Interface Card Following illustration shows an example for installing two expansion PCBs onto the KSU. Figure 2-57 Mounting Two Expansion Interface Cards Cut and remove the Plastic Knockouts as required for each Expansion interface card.

  • Page 61: Mounting The 4Coidb Pcb

    ISSUE 1.0 SL1100 Figure 2-58 Plastic Knockouts Replace the Main-Cover and fasten two screws. Figure 2-59 Replacing the Main-Cover 3.3.2 Mounting the 4COIDB PCB Cut and remove specified Plastic Knockouts on the 084M-B1/080E-B1/008E-B1/000E-B1 PCB. Hardware Manual 2-37...

  • Page 62: Figure 2-60 Plastic Knockouts On 084M-B1/080E-B1/008E-B1/000E-B1

    SL1100 ISSUE 1.0 Figure 2-60 Plastic Knockouts on 084M-B1/080E-B1/008E-B1/000E-B1 Insert two Nylon-spacers into the specified holes. Using supplied screw, fasten Metal Spacer to 4COIDB-B1 PCB. Mount the 4COIDB-B1 PCB onto the 084M-B1/080E-B1/008E-B1/000E-B1 PCB using two Nylon-spacers and one screw. (Refer to Installing the 4COIDB-B1) Attach the 4COIDB Label to the specified position on the 084M-B1/080E-B1/008E-B1/000E-B1 PCB.

  • Page 63: Mounting The 2Bridb Pcb

    ISSUE 1.0 SL1100 Figure 2-62 Mounting the 4COIDB-B1 into the KSU Replace the Main-Cover and fasten two screws. Figure 2-63 Replacing the Main-Cover 3.3.3 Mounting the 2BRIDB PCB Set the switches on the 2BRIDB-C1 PCB before mounting onto the 084M-B1/080E-B1/008E-B1/000E-B1 PCB, refer to the Switch Setting.

  • Page 64: Figure 2-64 Plastic Knockouts On 084M-B1/080E-B1/008E-B1/000E-B1

    SL1100 ISSUE 1.0 Figure 2-64 Plastic Knockouts on 084M-B1/080E-B1/008E-B1/000E-B1 Insert two Nylon-spacers into the specified holes. Using supplied screw, fasten Metal Spacer to 2BRIDB-C1 PCB. Mount the 2BRIDB-C1 PCB onto the 084M-B1/080E-B1/008E-B1/000E-B1 PCB using two Nylon-spacers and one screw. (Refer to Installing the 2BRIDB-C1) Attach the 2BRI Label to the specified position on the 084M-B1/080E-B1/008E-B1/000E-B1 PCB.

  • Page 65: Figure 2-66 Mounting The 2Bridb-C1 Into The Ksu

    ISSUE 1.0 SL1100 Figure 2-66 Mounting the 2BRIDB-C1 into the KSU Replace the Main-Cover and fasten two screws. Figure 2-67 Replacing the Main-Cover Hardware Manual 2-41...

  • Page 66: Cabling And Setting The Expansion Interface Card

    Aerial distribution wiring is not allowed.  Trunks must be installed with lightning protectors.  Only SL1100 terminals (12TXH, 24TXH) may be connected to a SL1100 digital port. Do not  connect any other terminal as damage may result. 3.4.1 Cabling IP4WW-080E-B1 This IP4WW-080E-B1 PCB provides two RJ-61 connections for digital extensions.

  • Page 67: Cabling Ip4[ ]-008E-B1

    Before plugging in the Multiline Telephone, DSS Console, Single line Telephone or Doorphone, ensure Main KSU is powered off. Only SL1100 terminals (12TXH, 24TXH) may be connected to a SL1100 digital port. Do not connect any other terminal as damage may result.

  • Page 68: Cabling Ip4Ww-000E-B1

    SL1100 ISSUE 1.0 While an Analogue Telephone (port) is ringing or MW-lamp is flashing on an Analogue Phone (port), do not disconnect the phone from the port and or connect another type of the terminal to this port. 3.4.2.1 Connectors The following table shows the pin-outs for the RJ-61 cable connector for Analogue extension connections.

  • Page 69: Cabling And Setting Ip4Ww-2Bridb-C1

    ISSUE 1.0 SL1100 Table 2-11 RJ-61 CO/PF Pin-Outs (J2, J3) Pin No. CO1-4 (J2): CO Port PF1 (J3): PF Tel Port Connector Connector (RJ-61) (RJ-61) T4 (Tip for port 4) T3 (Tip for port 3) T2 (Tip for port 2)

  • Page 70: Cabling And Setting Ip4Ww-1Priu-C1

    SL1100 ISSUE 1.0 Switch No. Switch Position Description T-Bus Point-to-Multipoint is selected, and if the system is  Terminal 8. (last device on the bus) S-Bus.  P-MP (Terminal 7) J13, J14/J16, J17 T (default) T-Bus connection S-Bus connection J12 & J15 do not configure the connection type on the system, they only add/remove the termination of the circuit.

  • Page 71: Table 2-14 Rj-45 Pri Pin-Outs (S-Bus, T-Bus)

    ISSUE 1.0 SL1100 Figure 2-73 Connector of 1PRIU-C1 3.4.6.1 Connector Following table shows the pin-outs for the RJ-45 cable connector for S-Bus and T-Bus RJ-45 connections. Table 2-14 RJ-45 PRI Pin-Outs (S-Bus, T-Bus) Pin No. RJ-45 Cable Connector- PRI 1...

  • Page 72: Table 2-16 Led Indication

    SL1100 ISSUE 1.0 Figure 2-74 Switches and LEDs Location of 1PRIU-C1 3.4.6.3 LED Indication LED indications for the IP4WW-1PRIU-C1 are listed in following table. Each LED is listed with its associated function and LED and operational status. Table 2-16 LED Indication...

  • Page 73: Power Failure Transfer (4Coidb-B1 Only)

    ISSUE 1.0 SL1100 Power Failure Transfer (4COIDB-B1 only) 3.5.1 General In the event of AC power failure, the specified trunk is directly connected to the specified extension port as below. And SLT must be connected to the specified extension. The multiline telephone (2W) does not work when the specified trunk is connected to the specified extension port.

  • Page 74: Section 4 Installing The Optional Interface Cards

    SL1100 ISSUE 1.0 SECTION 4 INSTALLING THE OPTIONAL INTERFACE CARDS Installing the Expansion Memory Card (MEMDB-C1) 4.1.1 General The Memory expansion daughter board (IP4[ ]-MEMDB-C1) provides additional memory for the system to use following features; To use VoIP Card (IP4WW-VOIPDB-C1) ...

  • Page 75: Figure 2-76 Removing The Main-Cover

    ISSUE 1.0 SL1100 Figure 2-76 Removing the Main-Cover Press tab A and lift the CPU support bracket. Remove the CPU card. Figure 2-77 Removing the CPU Card Insert the MEMDB-C1 daughter board to J4 socket on the CPU card and press down the MEMDB-C1 daughter board to secure.

  • Page 76: Figure 2-78 Installing The Memdb Pcb

    SL1100 ISSUE 1.0 Figure 2-78 Installing the MEMDB PCB Reinstall the CPU card into the 084M-B1 mother board, and close the CPU support making sure the tab A locks into place. Figure 2-79 Installing the CPU Card Replace the Main-Cover and fasten two screws.

  • Page 77: Voip Card (Voipdb-C1)

    ISSUE 1.0 SL1100 Figure 2-80 Replacing the Main-Cover VoIP Card (VOIPDB-C1) 4.2.1 General The IP4WW-VOIPDB-C1 daughter board is used to convert the RTP (Real Time Transfer Protocol) packets via the IP Network and PCM highway. The daughter board is installed on the CPU card.

  • Page 78: Figure 2-81 Removing The Sub-Cover

    SL1100 ISSUE 1.0 Figure 2-81 Removing the Sub-Cover Loosen two screws and remove the Main-Cover. Figure 2-82 Removing the Main-Cover Press tab A and lift the CPU support bracket. Remove the CPU card. 2-54 Installation...

  • Page 79: Figure 2-83 Removing The Cpu Card

    ISSUE 1.0 SL1100 Figure 2-83 Removing the CPU Card Install the VOIPDB-C1 daughter board to J5 connector on the CPU card. Figure 2-84 Installing the VOIPDB-C1 PCB Reinstall the CPU card into the 084M-B1 mother board, and close the CPU Support making sure tab A locks into place.

  • Page 80: Figure 2-85 Installing The Cpu Card

    SL1100 ISSUE 1.0 Figure 2-85 Installing the CPU Card Cut and remove the Plastic Knockout for VoIP connector, then replace the Main-Cover and fasten two screws. Figure 2-86 Removing the Plastic Knockout and Replacing the Main-Cover Connect the VOIPDB-C1 to an Switching hub using an LAN Cable.

  • Page 81: Led Indication

    ISSUE 1.0 SL1100 Figure 2-87 Connecting a LAN Cable Refer to the SL1100 Programming Manual for detailed programming instructions. The VoIP feature requires system configuration. 4.2.4 LED Indication LED indications for the IP4WW-VOIPDB-C1 are listed VOIPDB LED Indications. Each LED is listed with its associated function and operational status.

  • Page 82: Vrs/Voice Mail Card (Pz-Vm21)

    SL1100 ISSUE 1.0 Table 2-19 VOIPDB LED Indications Function LED Status Operation status Link activity or data transmission and On Green LED lights when link up is completed. LED flash reception. when data is transmitting or receiving. LINK1000 1000Base-T link speed indicator On Yellow Lights up when 1000Base-T link up.

  • Page 83: Figure 2-89 Removing The Sub-Cover

    ISSUE 1.0 SL1100 Figure 2-89 Removing the Sub-Cover Loosen two screws and remove the Main-Cover. Figure 2-90 Removing the Main-Cover Press tab A and lift the CPU support bracket. Remove the CPU card. Hardware Manual 2-59...

  • Page 84: Figure 2-91 Removing The Cpu Card

    SL1100 ISSUE 1.0 Figure 2-91 Removing the CPU Card Connect the PZ-VM21 daughter board to the J6 connector using four Nylon-spacers on the CPU card. Figure 2-92 Installing the PZ-VM21 PCB Reinstall the CPU card into the 084M-B1 mother board, and close the CPU Support making sure tab A locks into place.

  • Page 85: Installing The Cf Card (Cfvms)

    ISSUE 1.0 SL1100 Figure 2-93 Installing the CPU Card Replace the Main-Cover and fasten two screws. Figure 2-94 Replacing the Main-Cover Installing the CF Card (CFVMS) When installing a compact flash card onto the PZ-VM21 the system MUST be powered off. Never install or uninstall the compact flash card while the system is under power.

  • Page 86: Figure 2-95 Installing The Cf Card

    SL1100 ISSUE 1.0 Figure 2-95 Installing the CF Card Reinstall the CPU card into the 084M-B1 mother board, and close the CPU Support making sure tab A locks into place. 2-62 Installation...

  • Page 87: Section 5 Installing The Multiline Telephones And Optional Terminals

    ISSUE 1.0 SL1100 SECTION 5 INSTALLING THE MULTILINE TELEPHONES AND OPTIONAL TERMINALS Installing the Multiline Telephones There are three types of Multiline Telephones available in the SL1100 system. IP4WW-12TXH-B-TEL  IP4WW-24TXH-B-TEL  IP4WW-24TIXH-C-TEL (IP)  5.1.1 Location of Controls Handset...

  • Page 88: Multiline Telephone Legs Adjustment

    SL1100 ISSUE 1.0 Table 2-22 Multiline Telephone Functions (12TXH/24TXH/24TIXH (IP)) Functions 12TXH 24TXH 24TIXH Programming Keys (Busy lamp (Busy lamp (Busy lamp field: field: field: Red-Green) Red-Green) Red-Green) Display 24-digit x 3 lines with Backlit Handsfree Full-duplex Wall-Mount Kit Yes (Built-in)

  • Page 89: Figure 2-98 Cabling Of Multiline Telephone

    ISSUE 1.0 SL1100 Figure 2-98 Cabling of Multiline Telephone Turn telephone over (button side up). 5.1.2.2 High position setting Turn telephone over (button side down). Pull up the Leg Stoppers. Figure 2-99 Setting for High Position Adjust the leg to desired height.

  • Page 90: Wall-Mounting The Multiline Telephone

    SL1100 ISSUE 1.0 Figure 2-100 Leg Setting for High Position Lead the Line and Handset cords through the applicable grooves. (Refer to Cabling of Multiline Telephone) 5.1.3 Wall-Mounting the Multiline Telephone Arrange the cables and put down the leg as shown below.

  • Page 91: Figure 2-102 Wall-Mount Unit - 24Tixh-C

    ISSUE 1.0 SL1100 Figure 2-102 Wall-Mount Unit - 24TIXH-C Remove the switch-hook from the unit. Turn the tab toward the top. Then slide the hook-switch into position. Refer to Hook-Switch Hanger. Figure 2-103 Hook-Switch Hanger Install two screws into a wall. The screw heads must be remained about 3 mm (0.12″).

  • Page 92: Install The Ip Multiline Telephone (Ip4Ww-24Tixh-C1 Tel)

    SL1100 ISSUE 1.0 Figure 2-104 Wall-Mount Screw Guide Mount the telephone on the wall. Figure 2-105 Mounting the Multiline Telephone Install the IP Multiline Telephone (IP4WW-24TIXH-C1 TEL) 5.2.1 System Connection The IP Multiline Telephone is connected via HUB. 2-68 Installation...

  • Page 93: Installing The Ip Multiline Telephone

    ISSUE 1.0 SL1100 IP Multiline Tel ephone LAN Cable Exit Help (10BASE-T/100BASE-TX) Flas h Tra nsf e r Mute PQRS lea r /Back Spea ker Hold Ferrite Core VOIPDB-C1 LAN(=) Connector board (CN1) PC (X)Connector Commercial Power AC[ ]-[ ]...

  • Page 94: Installing The Dss Console

    SL1100 ISSUE 1.0 PoE(IEEE802.3af)  PoE (Power Over Ethernet) is a LAN technology that allows standard 10Base-T/100Base-TX data cables to pass electrical current from a power source to a requesting end device. Installing the DSS Console The 60D DSS-B Console can be installed on any digital extension port of 084M-B1/080E-B1 card directly.

  • Page 95: Wall-Mounting The Dss Console

    ISSUE 1.0 SL1100 Figure 2-110 Leg Stopper of DSS Console Adjust the leg to desired height. Figure 2-111 High Position Setting Lead the Line cord through the applicable grooves. (Refer to Cabling of DSS) 5.3.2 Wall-Mounting the DSS Console Lift the leg and lead the cable through the applicable grooves. Refer to Cabling for Wall-Mount.

  • Page 96: Installing The Headset

    SL1100 ISSUE 1.0 Figure 2-112 Cabling for Wall-Mount Install two screws into a wall. The screw heads must be remained about 3 mm (0.12″). Figure 2-113 Wall-Mount Screw Guide Mount the DSS Console to the wall. Figure 2-114 Mounting the DSS Installing the Headset The Multiline Telephone user can utilize a customer-provided headset in place of the handset.

  • Page 97: Installing The Doorphone Box

    ISSUE 1.0 SL1100 Operation provides privacy not available from Handsfree. Connect the Headset cord into the Headset socket. Figure 2-115 Headset Socket (2-wire Multiline Telephone) Figure 2-116 Headset Socket (IP Multiline Telephone) The headset configuration is assigned using system programming.

  • Page 98: Figure 2-117 Doorphone Box And Bracket

    SL1100 ISSUE 1.0 Figure 2-117 Doorphone Box and Bracket Mount the Wall-Mount bracket on the wall using supplied screws. Replace the Upper housing and tighten the screw. Figure 2-118 Doorphone 2-74 Installation...

  • Page 99: Connecting The Doorphone

    ISSUE 1.0 SL1100 5.5.2 Connecting the Doorphone Figure 2-119 Connecting the Doorphone The Doorphone configuration is assigned using system programming. The 3 party Doorphone Boxes cannot be connected to the port. 5.5.3 Doorphone Interface Specifications Table 2-23 Doorphone Interface Specifications...

  • Page 100: Installing The External Paging Speaker/External Moh/Bgm Sources

    SL1100 ISSUE 1.0 Figure 2-120 Connecting the Door Unlock Device The following table shows the pin-outs for the RJ-61 cable connector. Table 2-24 RJ-61 General Purpose/Door Unlock Relay Control Connector (J7) Pin No. Connection Relay 2 Relay 1 Relay 1...

  • Page 101: External Paging Output Specifications

    ISSUE 1.0 SL1100 Figure 2-121 Connecting Audio Equipment 5.7.2 External Paging Output Specifications Table 2-26 External Paging Output Specifications Item Specification Output Impedance 600 Ω @ 1kHz Output Level Nominal 250 mV (-10 dBm) Maximum Output 400 mV RMS 5.7.3...

  • Page 102: Smdr (Station Message Detail Recording)

    SL1100 ISSUE 1.0 SMDR (Station Message Detail Recording) 5.8.1 General SMDR (Station Message Detail Recording) provides a record of the system's outside calls. Typically, the record outputs to a customer-provided SMDR device such as PC via LAN port (J3) on the CPU card.

  • Page 103: System Start Up

    System Start Up SECTION 1 SYSTEM START UP Before Starting Up the System Before starting up the system, make sure: KSU is installed correctly.  All extensions are cabled correctly.  Earth ground and PSTN Trunks are cabled correctly.  All PCBs are configured, equipped, and secured correctly.

  • Page 104: Figure 3-2 Power Switch Location

    SL1100 ISSUE 1.0 System software is loaded from flash memory, and the customer data is deleted from RAM memory. To perform a Cold Start; Set the power switch to off position. Figure 3-2 Power Switch Location Open the Sub-Cover on the Main KSU and identify the LOAD button (S1) location on the CPU card.

  • Page 105: Perform A Hot Start

    ISSUE 1.0 SL1100 Figure 3-4 Status LED (D5) and RUN LED Location Release the LOAD button. When the system has completed reloading the software (about two minutes), the RUN LED is flashing blue on the CPU card and the connected Multiline Telephone's display will show the Time &...

  • Page 106: Section 2 Programming Mode

    Dial the system password, then press Hold key to enter the Program Mode. Figure 3-7 Entering Programming Mode Display 2 For the details of programming, refer to the SL1100 Programming Manual. (separate issue) Exiting the Programming Mode Press Mute key several times to return to the "Program Mode" Screen.

  • Page 107: Saving (Backup) The Customer Data

    ISSUE 1.0 SL1100 Saving (Backup) the Customer Data When the installer/system administrator exits from the programming mode, the system will automatically save the customer data to the on-board memory which is backed up by lithium battery. Additionally, the customer data can be saved to a CF Card for backup purpose. The PZ-VM21 daughter board must be installed to the CPU card with a BLANK CF card inserted.

  • Page 108: Figure 3-13 Inserting The Cf Card

    SL1100 ISSUE 1.0 For the details of PZ-VM21 daughter board installation, refer to Installing the PZ-VM21 PCB. Turn the power off, insert the Customer Data CF card into the CF Slot on PZ-VM21. Figure 3-13 Inserting the CF card Turn the power on, enter the Program Mode then PRG90-04.

  • Page 109: Section 3 System Shut Down

    ISSUE 1.0 SL1100 SECTION 3 SYSTEM SHUT DOWN Powering Off the System Turn the KSU power off using the power switch. Figure 3-16 Power Switch Location DO NOT power off by disconnecting the AC (or DC for battery backup) power. Always use the Power Switch on the Main KSU.
  • Page 110 SL1100 ISSUE 1.0 MEMO System Start Up...

  • Page 111: Chapter4 Maintenance

    Maintenance SECTION 1 FUSE REPLACEMENT Replacing the Fuse This fuse is only for external battery box connection, it is not used for AC power to the system. Turn off the system power and disconnect AC cord. Open and remove the Sub-Cover. Figure 4-1 Removing the Sub-Cover Loosen two screws and remove the Main-Cover.

  • Page 112: Figure 4-3 Exchanging The Fuse

    SL1100 ISSUE 1.0 Exchange the fuse (250 V/8 A) on 084M-B1 PCB. Figure 4-3 Exchanging the Fuse Replace the Main-Cover and fasten two screws. Figure 4-4 Replacing the Main-Cover Maintenance...

  • Page 113: Section 2 Lithium Battery Replacement

    Before replacing the Lithium battery, make sure which type of Lithium battery is required and prepare the new Lithium battery. (CR2032) NEC recommends that a backup of the customer data is performed before powering off the system (either PCPro file or CF card backup) in order to replace the backup battery.

  • Page 114: Figure 4-6 Removing The Sub-Cover

    SL1100 ISSUE 1.0 Figure 4-6 Removing the Sub-Cover Power off the system, and remove the AC plug from the AC outlet. Disconnect the AC power cord from the KSU. AC power cord must be disconnected, otherwise the Main-Cover cannot be opened.

  • Page 115: Figure 4-8 Removing The Main-Cover

    ISSUE 1.0 SL1100 Figure 4-8 Removing the Main-Cover Press tab A and lift the CPU support bracket. Remove CPU card from the Main KSU. Figure 4-9 Removing the CPU Card Refer to following figure for the Lithium battery location on the CPU card.

  • Page 116: Figure 4-10 Location Of Lithium Battery Socket

    SL1100 ISSUE 1.0 Figure 4-10 Location of Lithium Battery Socket Remove the old Lithium battery and insert the new one into the socket. The polarity “+” symbol must be on top as illustrated in following figure. Figure 4-11 Removing the Lithium Battery Figure 4-12 Inserting the Lithium Battery Reinstall the CPU card into the 084M-B1 mother board and close the CPU support bracket.

  • Page 117: Figure 4-13 Installing The Cpu Card

    ISSUE 1.0 SL1100 Figure 4-13 Installing the CPU Card 10. Replace the Main-Cover and Sub-Cover. Hardware Manual...

  • Page 118: Section 3 Main Software Upgrading

    Prepare the CF Card (32MB, or upwards and formatting by FAT(16)), and store the new main  software on the CF card by PC. (New main system software is supplied by NEC.) Install the PZ-VM21 PCB. (if the system does not have it.) ...

  • Page 119: Upgrading The Main Software

    ISSUE 1.0 SL1100 Press Enter Key (Navigation Key) to show the main system software version and Hardware Key Code. Off-Hook and return to Time & Date mode. Upgrading the Main Software Power off the system and disconnect the AC cord from the KSU.

  • Page 120: Figure 4-16 Removing The Main-Cover

    SL1100 ISSUE 1.0 Figure 4-16 Removing the Main-Cover Insert the CF card (with the new main system software loaded) to the CF slot on PZ-VM21 daughter board. (PZ-VM21 should be temporary installed if not already fitted.) Figure 4-17 Inserting the CF card Push in and hold the LOAD button (S1 on the CPU card).

  • Page 121: Table 4-1 Status Leds

    ISSUE 1.0 SL1100 Turn the system power on. Continue holding the LOAD button (S1) for approximately 10 seconds or until Status LED (D5) starts flashing red. Release the LOAD button (S1). Wait until the Status LEDs (D2 to D5) on the CPU card has the following indications (approximately two minutes).

  • Page 122: Section 4 Led Indications

    SL1100 ISSUE 1.0 SECTION 4 LED INDICATIONS The LEDs on the CPU indicate the following: RUN (D1) = The CPU is operating (Blue)  D2, and D3 = Alarms (Red)  D4 = Flash access indication (Red)  D5 = Boot status (Red) ...

  • Page 123: Specifications

    Specifications SECTION 1 SYSTEM CAPACITY Table 5-1 System Capacity Items 1 KSU (1228) Description Note Expansion Slot System Maximum Port 1KSU: 084M+PRI+080E+4COIDBx2 Trunk Port Max. 1KSU: PRIx1+4COIDB/BRIx2 Trunk Port Analogue Trunks 1KSU: 4COIDBx3 on (COT) 084M/080E/008E/000E BRI (T-Point) 1KSU: 2BRIx3 on 084M/080E/008E/000E PRI (30B) Max.

  • Page 124: Section 2 System Specifications

    SL1100 ISSUE 1.0 SECTION 2 SYSTEM SPECIFICATIONS General Precautions Never attempt to insert wires, pins, etc. into the vents or other holes of the equipment.  Do not use benzene, thinner, or the like, or any abrasive powder to clean the equipment. Wipe it ...

  • Page 125: Electrical Specifications (Ksu)

    ISSUE 1.0 SL1100 110VAC 120VAC 220VAC 230VAC 240VAC AC Input I Main KSU = Main KSU = Main KSU = Main KSU = Main KSU = 1.16 A 1.08 A 0.70 A 0.67 A 0.65 A Main KSU = Main KSU =...

  • Page 126: 2.10 Ieee802.Af Class Specification

    SL1100 ISSUE 1.0 2.10 IEEE802.af Class Specification Table 5-6 IEEE802.af Class Specification IEEE802.af Minimum Maximum Class 2 3.84 W 6.49 W 2.11 Mechanical Specifications Table 5-7 Mechanical Specifications Equipment Width Depth Height Weight Note 1228M-B KSU 375 mm 115 mm 290 mm Approx.

  • Page 127: 2.14 General Purpose/Door Unlock Relay Specifications

    ISSUE 1.0 SL1100 2.14 General Purpose/Door Unlock Relay Specifications Table 5-10 General Purpose/Door Unlock Relay Specifications Item Specification Rated Voltage DC 48 V Maximum Rated Current DC 320 mA Maximum Contact Normally Open 2.15 External Paging Output Specifications Table 5-11 External Paging Output Specifications...

  • Page 128: 2.20 Cable Requirements

    SL1100 ISSUE 1.0 2.20 Cable Requirements Table 5-15 Cable Requirements Device Cable Type Cable Run Length Multiline Telephone 24 AWG (Φ0.5 mm) 300 m (984.3 ft) Multiline IP Telephone CAT5 Straight Cable 100 m (328.1 ft) DSS Console 24 AWG (Φ0.5 mm) 300 m (984.3 ft)
  • Page 129 MEMO...
  • Page 130 Hardware Manual NEC Corporation ISSUE 1.0 (R2.0)

Table of Contents