Initializing The B, 1B Page Data; Initialization Of Bluetooth Unit (Dcr-Ip220/Ip220E) - Sony DCR-IP210 Adjustment

DCR-IP210/IP210E/IP220/IP220E
1-2-2. INITIALIZATION OF B, 1B PAGE DATA
Note: When reading or writing the B page data, select page: 0, address:
10, and set data: 00.
When reading or writing the 1B page data, select page: 0, address:
10, and set data: 01, then select B page. The 1B page can be chosen
by this data setting.
After reading or writing, reset the data of page: 0, address: 10 to
"00".

1. Initializing the B, 1B Page Data

Note1: If "Initializing the B, 1B Page Data" is performed, all data of the
B page and 1B page will be initialized. (It is impossible to initialize
a single page.)
Note2: If the B, 1B page data has been initialized, the following
adjustments need to be performed again.
1) Modification of B, 1B page data
Adjusting page
Adjusting Address
Adjusting page
Adjusting Address
Initializing Method:
Order Page Address Data
1 0 01
2 0 10
3 5 0E
4 5 01
5 5 00
6 5 0E
7 5 0E
8 5 03
9 5 01 FA
10 5 00
11 5 0E
12
B
00 to FF
1B
00 to FF
Procedure
01 Set the data.
00 Set the data.
00 Set the data, and press PAUSE
button.
F3 Set the data, and press PAUSE
button.
01 Set the data, and press PAUSE
button.
Check that the data changes to
"01".
00 Set the data, and press PAUSE
button.
20 Set the data, and press PAUSE
button.
Set the data, and press PAUSE
button.
01 Set the data, and press PAUSE
button.
Check that the data changes to
"01".
Turn off the power and turn on
again.
2. Modification of B, 1B Page Data
If the B, 1B page data has been initialized, change the data of the
"Fixed data-2" address shown in the following tables by manual
input.
Modifying Method:
1) Before changing the data, select page: 0, address: 01, and set
data: 01.
2) When changing the B page data, select page: 0, address: 10,
and set data: 00.
3) When changing the 1B page data, select page: 0, address: 10,
and set data: 01.
After completing the modification of 1B page data, reset the
data of this address to "00".
4) New data for changing are not shown in the tables because
they are different in destination. When changing the data, copy
the data built in the same model.
Note: If copy the data built in the different model, the camcorder may
not operate.
5) When changing the data, press the PAUSE button of the
adjustment remote commander each time when setting new
data to write the data in the non-volatile memory.
Processing after Completing Modification of B, 1B Page data:
Order Page Address Data
1 0 10
2 2 00
3 2 01

3. Initialization of Bluetooth Unit (DCR-IP220/IP220E)

Register the model name in the bluetooth unit.
Note: This initialization should be carried out upon completion of
"Initializing the 4, 8, 9, C Page Data".
Order Page Address Data
1
2
3 0 10
4 7 0A
5
6
7
6-12
Procedure
00 Set the data.
29 Set the data.
29 Set the data, and press PAUSE
button.
Procedure
Set the POWER switch to OFF.
Set the POWER switch to
MEMORY.
00 Set the data.
72 Set the data.
Check that the LCD screen
display the network menu.
Wait for 5 seconds.
Set the POWER switch to OFF.