1. Manuals
  2. Brands
  3. Sony Manuals
  4. Camcorder
  5. DCR-IP210
  6. Adjustment

Sony DCR-IP210 Adjustment

Hide thumbs Also See for DCR-IP210:
Table of Contents

Advertisement

Quick Links

Download this manual
Ver 1.1 2003. 05
Revision History
Revision History
Link
Link
Before starting adjustment
Before starting adjustment
Adjusting items when replacing main parts and boards
Adjusting items when replacing main parts and boards
CAMERA SECTION ADJUSTMENT
CAMERA SECTION ADJUSTMENT
PREPARATIONS BEFORE ADJUSTMENT
PREPARATIONS BEFORE ADJUSTMENT
INITIALIZATION OF 4, 8, 9, A, B, C, D, E, F, 1B, 1E, 1F PAGE DATA
INITIALIZATION OF 4, 8, 9, A, B, C, D, E, F, 1B, 1E, 1F PAGE DATA
CAMERA SYSTEM ADJUSTMENTS
CAMERA SYSTEM ADJUSTMENTS
COLOR ELECTRONIC VIEWFINDER SYSTEM ADJUSTMENT
COLOR ELECTRONIC VIEWFINDER SYSTEM ADJUSTMENT
LCD SYSTEM ADJUSTMENT
LCD SYSTEM ADJUSTMENT
MECHANISM SECTION ADJUSTMENT
MECHANISM SECTION ADJUSTMENT
Adjustment Remote Commander
Adjustment Remote Commander
OPERATING WITHOUT CASSETTE
OPERATING WITHOUT CASSETTE
TAPE PATH ADJUSTMENT
TAPE PATH ADJUSTMENT
Contents of LEVEL 2 and LEVEL 3 Service Manual
CONTENTS
1. SERVICE NOTE
2. DISASSEMBLY
3. BLOCK DIAGRAMS
4. PRINTED WIRING BOARDS AND
SCHEMATIC DIAGRAMS
5. REPAIR PARTS LIST
9-929-995-51
SECTION 6
ADJUSTMENTS
VIDEO SECTION ADJUSTMENT
VIDEO SECTION ADJUSTMENT
SERVICE MODE
SERVICE MODE
LEVEL 2
a
a
OVERALL
POWER
BT-012, AN-025, LD-112,
ST-076, JK-234, SW-380,
PK-067, PD-166, VF-155,
DC-098 BOARD,
FLASH UNIT (FL-2980),
CONTROL SWITCH BLOCK
(SS-2980, PW-2980),
FP-538, FP-539, FP-554,
FP-540, FP-541, FP-542
FLEXIBLE
EXPLODED VIEWS
ELECTRICAL PARTS
Sony EMCS Co.
DCR-IP210/IP210E/
IP220/IP220E
PREPARATIONS BEFORE ADJUSTMENTS
PREPARATIONS BEFORE ADJUSTMENTS
SYSTEM CONTROL SYSTEM ADJUSTMENT
SYSTEM CONTROL SYSTEM ADJUSTMENT
SERVO AND RF SYSTEM ADJUSTMENT
SERVO AND RF SYSTEM ADJUSTMENT
VIDEO SYSTEM ADJUSTMENTS
VIDEO SYSTEM ADJUSTMENTS
AUDIO SYSTEM ADJUSTMENTS
AUDIO SYSTEM ADJUSTMENTS
ADJUSTMENT REMOTE COMMANDER
ADJUSTMENT REMOTE COMMANDER
DATA PROCESS
DATA PROCESS
SERVICE MODE
SERVICE MODE
LEVEL 3
CD-406, DI-087, VC-308 BOARD
a (CD-406, DI-087, VC-308 BOARD)
Published by DI Customer Center
RMT-817
ADJ
2002I1600-1
©2002.9

Advertisement

Table of Contents
loading

Related Manuals for Sony DCR-IP210

Summary of Contents for Sony DCR-IP210

  • Page 1 DC-098 BOARD, FLASH UNIT (FL-2980), CONTROL SWITCH BLOCK (SS-2980, PW-2980), FP-538, FP-539, FP-554, FP-540, FP-541, FP-542 FLEXIBLE 5. REPAIR PARTS LIST EXPLODED VIEWS ELECTRICAL PARTS a (CD-406, DI-087, VC-308 BOARD) 2002I1600-1 ©2002.9 Sony EMCS Co. 9-929-995-51 Published by DI Customer Center...

  • Page 2: Table Of Contents

    DCR-IP210/IP210E/IP220/IP220E TABLE OF CONTENTS ADJUSTMENT AF Laser Axis Check ···················································· 6-35 Steady Shot Check ························································· 6-36 Before starting adjustment ··············································· 6-1 1-4. COLOR ELECTRONIC VIEWFINDER SYSTEM 1-1. Adjusting items when replacing main parts and boards. · 6-2 ADJUSTMENT ····························································· 6-37 6-1.
  • Page 3 DCR-IP210/IP210E/IP220/IP220E 6-4. SERVICE MODE ·························································· 6-65 4-1. ADJUSTMENT REMOTE COMMANDER ················ 6-65 Using the adjustment remote commander ····················· 6-65 Precautions upon using the adjustment remote commander ···································································· 6-65 4-2. DATA PROCESS ··························································· 6-66 4-3. SERVICE MODE ·························································· 6-67 Setting the Test Mode ···················································· 6-67 Emergence Memory Address ········································...

  • Page 4: Before Starting Adjustment

    DCR-IP210/IP210E/IP220/IP220E SECTION 6 COVER COVER ADJUSTMENTS Before starting adjustment EVR Data Re-writing Procedure When Replacing Board The data that is stored in the repair board, is not necessarily correct. Perform either procedure 1 or procedure 2 or procedure 3 when replacing board.

  • Page 5: Adjusting Items When Replacing Main Parts And Boards

    DCR-IP210/IP210E/IP220/IP220E COVER COVER 1-1. Adjusting items when replacing main parts and boards. • Adjusting items when replacing main parts When replacing main parts, adjust the items indicated by in the following table. Note1: When replacing the drum assy. or the mechanism deck, reset the data of page: 7, address: A7 to A9 to “00”. (Refer to “Record of Use check” of “6-4.
  • Page 6 DCR-IP210/IP210E/IP220/IP220E • Adjusting items when replacing a board or EEPROM When replacing a board or FFPROM, adjust the items indicated by in the following table. Note2: When the repair is finished, confirm the Board EEPROM following items. replacement replacement Shoot the all black subject (Attach the...

  • Page 7: Camera Section Adjustment

    DCR-IP210/IP210E/IP220/IP220E COVER COVER 6-1. CAMERA SECTION ADJUSTMENT 1-1. PREPARATIONS BEFORE ADJUSTMENT (CAMERA SECTION) 1-1-1. List of Service Tools • Oscilloscope • Color monitor • Vectorscope • Regulated power supply • Digital voltmeter Ref. No. Name Parts Code Usage Filter for color temperature correction (C14)
  • Page 8 DCR-IP210/IP210E/IP220/IP220E J-10 J-11 Fig. 6-1-1.

  • Page 9: Preparations

    DCR-IP210/IP210E/IP220/IP220E 1-1-2. Preparations Pattern box Note1: For details of how remove the cabinet and boards, refer to “2. DISASSEMBLY”. Note2: When performing only the adjustments, the lens block and boards need not be disassembled. Note3: Before performing the adjustments, check the data of page: 0, address: 10 is “00”.
  • Page 10 DCR-IP210/IP210E/IP220/IP220E * 1: When using AC-VF50, a DC connection code (DK-225) is separately necessary. * 2: DCR-IP220/IP220E only S video Color monitor Vector scope Video (yellow) Terminated at 75 Ω . Audio left (white) EVF block AC power adaptor Adjustment Audio Right (Red) (8.4Vdc)

  • Page 11: Precaution

    DCR-IP210/IP210E/IP220/IP220E 1-1-3. Precaution 1. Setting the Switch Unless otherwise specified, set the switches as follows and perform adjustments without loading cassette. POWER (PW-2980 block) ........CAMERA CAMERA SET of the MENU settings FOCUS (FP-539 flexible) ........MANUAL DIGITAL ZOOM ..........OFF NIGHT SHOT (FP-538 flexible) ........

  • Page 12: Preparing The Flash Adjustment Box

    DCR-IP210/IP210E/IP220/IP220E 4. Preparing the Flash Adjustment Box A dark room is required to provide accurate flash and AF laser adjustments. If it is not available, prepare the flash adjustment box as given below; woody board A (2 sheets) woody board B (2 sheets)

  • Page 13: Initialization Of 4, 8, 9, A, B, C, D, E, F

    1) Before changing the data, select page: 0, address: 01, and set 1) Modification of A, D page data data: 01. Note3: NTSC model: DCR-IP210/IP220 2) New data for changing are not shown in the tables because PAL model: DCR- IP210E/IP220E they are different in destination.
  • Page 14 DCR-IP210/IP210E/IP220/IP220E 3. A Page Table 4. D Page Table Note1: The data of page: 0, address: 10 must be “00”. Note1: The data of page: 0, address: 10 must be “00”. Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the A, D Note2: Fixed data-1: Initialized data.

  • Page 15: Initializing The B, 1B Page Data

    DCR-IP210/IP210E/IP220/IP220E 1-2-2. INITIALIZATION OF B, 1B PAGE DATA 2. Modification of B, 1B Page Data If the B, 1B page data has been initialized, change the data of the Note: When reading or writing the B page data, select page: 0, address: “Fixed data-2”...

  • Page 16: Writing The Network Default Setting Value

    DCR-IP210/IP210E/IP220/IP220E 4. Writing the Network Default Setting Value 5. B Page Table (DCR-IP220/IP220E) Note1: The data of page: 0, address: 10 must be “00”. Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the B, 1B Mode VTR stop Page Data”.) Fixed data-2: Modified data.

  • Page 17: Initialization Of E, F, 1E, 1F Page Data

    3) Camera system adjustments Note: If copy the data built in the different model, the camcorder may Note3: NTSC model: DCR-IP210/IP220 not operate. PAL model: DCR- IP210E/IP220E 5) When changing the data, press the PAUSE button of the...
  • Page 18 DCR-IP210/IP210E/IP220/IP220E 3. E Page Table Address Remark Note1: The data of page: 0, address: 10 must be “00”. 56 to 5A Fixed data-1 Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the E, F, Fixed data-2 1E, 1F Page Data”.) Fixed data-2: Modified data.
  • Page 19 DCR-IP210/IP210E/IP220/IP220E 4. F Page Table Address Initial value Initial value Remark Note1: The data of page: 0, address: 10 must be “00”. NTSC PAL Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the E, F, Flange back adj. 1E, 1F Page Data”.) Fixed data-2: Modified data.
  • Page 20 DCR-IP210/IP210E/IP220/IP220E F Page Address Initial value Initial value Remark NTSC PAL Mechanical shutter adj. Strobe light level adjustment 92 to 99 Fixed data-1 Fixed data-2 Fixed data-1 Fixed data-2 9E to A4 Fixed data-1 Fixed data-2 A7 to AA Fixed data-1...
  • Page 21 DCR-IP210/IP210E/IP220/IP220E 5. 1E Page Table 6. 1F Page Table Note1: When reading or writing the 1E page data, select page: 0, address: Note1: When reading or writing the 1F page data, select page: 0, address: 10, and set data: 01, then select E page. The 1E page can be chosen 10, and set data: 01, then select F page.

  • Page 22: E Page Table

    DCR-IP210/IP210E/IP220/IP220E 1-2-4. INITIALIZATION OF 4, 8, 9, C PAGE DATA 2. Modification of 4, 8, 9, C Page Data If the 4, 8, 9, C page data has been initialized, change the data of the Note: The data of page: 0, address: 10 must be “00”.

  • Page 23: Page Table

    DCR-IP210/IP210E/IP220/IP220E 4. 8 Page Table 6. C Page Table Note1: The data of page: 0, address: 10 must be “00”. Note1: The data of page: 0, address: 10 must be “00”. Note2: Fixed data-1: Initialized data. (Refer to “1. Initializing the 4, 8, 9, Note2: Fixed data-1: Initialized data.
  • Page 24 DCR-IP210/IP210E/IP220/IP220E C Page Address Address Remark Remark Address Address Remark Remark Initial value Initial value Initial value Initial value Pch LMS adj. VCO adj. (EVF) Fixed data-1 VCO adj.(LCD) V-COM adj. (LCD) Bright adj. (LCD) Black limit adj.(LCD) PSIG GRAY adj. (LCD) White balance adj.

  • Page 25: Camera System Adjustments

    DCR-IP210/IP210E/IP220/IP220E COVER COVER 1-3. CAMERA SYSTEM ADJUSTMENTS Before perform the camera system adjustments (except for “67.5MHz/54MHz Origin Oscillation Adjustment”), check that the specified values of “VIDEO SYSTEM ADJUSTMENTS” are satisfied. And check that the data of page: 0, address: 10 is “00”. If not, set data: 00 to this address.

  • Page 26: Hall Adjustment

    DCR-IP210/IP210E/IP220/IP220E 3. HALL Adjustment Processing after Completing Adjustments: For detecting the position of the lens iris and ND filter, adjust AMP Order Page Address Data Procedure gain and offset. Set the data, and press PAUSE Subject Not required button. Measurement Point Display data of page 1 (Note1) Set the data.

  • Page 27: Ccd Output 2Ch Matching Adjustment (2)

    DCR-IP210/IP210E/IP220/IP220E 5. CCD Output 2ch Matching Adjustment (2) 6. MR Adjustment Correct the dispersion between the left-right channels of the CCD The MR (Magnet resistor) adjustment of the inner focus lens is imager. carried out automatically. In whichever case, the focus will be deviated during auto focusing/manual focusing.
  • Page 28 DCR-IP210/IP210E/IP220/IP220E 7. Flange Back Adjustment Adjusting method: (Using Minipattern Box) Order Page Address Data Procedure The inner focus lens flange back adjustment is carried out Set the data. automatically. In whichever case, the focus will be deviated during auto focusing/manual focusing.

  • Page 29: Flange Back Adjustment (Using Flange Back Adjustment Chart And Subject More Than 500M Away)

    DCR-IP210/IP210E/IP220/IP220E 8. Flange Back Adjustment (Using Flange Back Adjustment Chart and Subject More Than 500m Away) The inner focus lens flange back adjustment is carried out automatically. In whichever case, the focus will be deviated during auto focusing/manual focusing. 8-1. Flange Back Adjustment (1)

  • Page 30: Flange Back Adjustment (2)

    DCR-IP210/IP210E/IP220/IP220E 8-2. Flange Back Adjustment (2) 9. Flange Back Check Perform this adjustment after performing “Flange Back Adjustment Subject Siemens star (1)”. (2.0m from the front of the lens) Subject Subject more than 500m away (Luminance : approx. 200 lux)

  • Page 31: Max Gain Adjustment

    1) POWER ..............CAMERA Note3: The data of page: 0, address: 10 must be “00”. 2) NIGHT SHOT ..............OFF Note4: NTSC model: DCR-IP210/IP220 3) DIGITAL ZOOM (Menu display) ........OFF PAL model: DCR- IP210E/IP220E 4) STEADY SHOT (Menu display) ........OFF...

  • Page 32: Color Reproduction Adjustment

    All color luminance points should For NTSC model settle within each color reproduction frame. Note1: The data of page: 0, address: 10 must be “00”. Note2: NTSC model: DCR-IP210/IP220 PAL model: DCR- IP210E/IP220E Switch setting: POWER ..............CAMERA NIGHT SHOT ..............OFF DIGITAL ZOOM (Menu display) ........

  • Page 33: Auto White Balance & Lv Standard Data Input

    DCR-IP210/IP210E/IP220/IP220E 13. Auto White Balance & LV Standard Data Input Adjust the white balance reference at 3200K, and adjust the normal coefficient of the light value. Subject Clear chart (Color reproduction adjustment frame) Measurement Point Display data of page 1 (Note5)

  • Page 34: Auto White Balance Adjustment

    DCR-IP210/IP210E/IP220/IP220E 14. Auto White Balance Adjustment Adjusting method: Adjust to the proper auto white balance output data. Order Page Address Data Procedure If it is not correct, auto white balance and color reproducibility will Place the C14 filter for color be poor.

  • Page 35: White Balance Check

    DCR-IP210/IP210E/IP220/IP220E 15. White Balance Check Subject Clear chart (Color reproduction adjustment frame) Filter Filter C14 for color temperature correction ND filter 1.0 and 0.4 and 0.1 Measurement Point Video terminal of A/V jack (75Ω terminated) Measuring Instrument Vectorscope Specified Value Fig.

  • Page 36: Mechanical Shutter Adjustment

    76 to 8B (50cm from the front of the lens)(Note1) Note1: The data of page: 0, address: 10 must be “00”. Measurement Point Adjustment remote commander Note2: NTSC model: DCR-IP210/IP220 Measuring Instrument PAL model: DCR- IP210E/IP220E Adjustment Page Adjusting method:...

  • Page 37: Strobe White Balance Adjustment & Check

    DCR-IP210/IP210E/IP220/IP220E 18. Strobe White Balance Adjustment & Check 19. AF Laser Output Adjustment Adjust and check the white balance when the strobe light flashes. Set the AF laser output to an appropriate level. Subject Paper which reflection rate is 18%...

  • Page 38: Af Laser Axis Check

    DCR-IP210/IP210E/IP220/IP220E 20. AF Laser Axis Check Inspection frame Subject Dark homogeneous subject (1m from the front of the lens) (Note1) Measurement Point Video terminal of A/V jack Measuring Instrument Monitor TV Specified Value Two or more hologram lines are perfectly within the inspection frame.

  • Page 39: Steady Shot Check

    DCR-IP210/IP210E/IP220/IP220E 21. Steady Shot Check Precautions on the Parts Replacement There are two types of repair parts. Type A: ENC03MA Type B: ENC03MB Replace the broken sensor with a same type sensor. If replace with other type parts, the image will vibrate up and down or left and right during hand-shake correction operations.

  • Page 40: Color Electronic Viewfinder System

    DCR-IP210/IP210E/IP220/IP220E COVER COVER 1-4. COLOR ELECTRONIC VIEWFINDER [Measuring points] The measuring points for manual adjustment are Pin eg (EXT DA) SYSTEM ADJUSTMENT and Pin ws (VG) of IC2201 of DI-087 board. Note1: When replacing the LCD unit, be careful to prevent damages caused by static electricity.

  • Page 41: Adjustment

    DCR-IP210/IP210E/IP220/IP220E 1. Back Light Adjustment (DI-087 board) Set the brightness of the back light to the specified level. If deviated, the EVF screen will become too bright or too dark. Note: Do either of the automatic adjustment or the manual adjustment.

  • Page 42: Manual Adjustment

    DCR-IP210/IP210E/IP220/IP220E 2. Bright Adjustment (DI-087 board) 2-2. Manual Adjustment Set the D range of the RGB decoder used to drive the LCD to the Mode Camera specified value. If deviated, the LCD screen will become blackish Subject Arbitrary or saturated (whitish).

  • Page 43: Manual Adjustment

    DCR-IP210/IP210E/IP220/IP220E 3. Contrast Adjustment (DI-087 board) 3-2. Manual Adjustment Set the level of the VIDEO signal for driving the LCD to the specified Mode Camera value. If deviated, the screen image will be blackish or saturated Subject Arbitrary (whitish). Measurement Point Pin ws (VG) of IC2201 Note: Do either of the automatic adjustment or the manual adjustment.

  • Page 44: White Balance Adjustment (Di-087 Board)

    Specified Value The EVF screen should not be colored. Specified Value The EVF screen should be stable. Note1: NTSC model: DCR-IP210/IP220 Note1: Check the white balance only when replacing the following parts. PAL model: DCR-IP210E/IP220E If necessary, adjust them. Note2: The data of page: 0, address: 10 must be “00”.
  • Page 45 DCR-IP210/IP210E/IP220/IP220E Adjusting method for NTSC model: Adjusting method for PAL model: Order Page Address Data Procedure Order Page Address Data Procedure Set the data. Set the data. Set the data, and press PAUSE button. Set the data, and press PAUSE button.

  • Page 46: Lcd System Adjustment

    = 15625 ± 30Hz (PAL) [Adjusting connector] Most of the measuring points for adjusting the LCD system are Note1: NTSC: DCR-IP210/220 concentrated in CN803 of the PD-166 board. Connect the Measuring PAL: DCR-IP210E/220E Instruments via the CPC-jig for LCD panel (J-6082-529-A).

  • Page 47: Bright Adjustment (Pd-166 Board)

    DCR-IP210/IP210E/IP220/IP220E 2. Bright Adjustment (PD-166 Board) 3. Black Limit Adjustment (PD-166 Board) Set the video signal level for driving the LCD to the specified value. Set the video signal level for driving the LCD driver to an appropriate If deviated, the LCD screen will become blackish or saturated level.

  • Page 48: Psig Gray Adjustment (Pd-166 Board)

    DCR-IP210/IP210E/IP220/IP220E 4. PSIG GRAY Adjustment (PD-166 Board) 5. Contrast Adjustment (PD-166 Board) Set the PSIG signal level to an appropriate level. Set the level of the VIDEO signal for driving the LCD to the specified value. If deviated, the screen image will be blackish or saturated...

  • Page 49: Center Level Adjustment (Pd-166 Board)

    DCR-IP210/IP210E/IP220/IP220E 6. Center Level Adjustment (PD-166 Board) 7. V-COM Adjustment (PD-166 Board) Set the video signal center level of LCD panel to an appropriate Set the DC bias of the common electrode drive signal of LCD to the level. specified value.

  • Page 50: White Balance Adjustment (Pd-166 Board)

    DCR-IP210/IP210E/IP220/IP220E 8. White Balance Adjustment (PD-166 Board) Correct the white balance. If deviated, the reproduction of the LCD screen may degenerate. Mode VTR stop Signal No signal Measurement Point Check on LCD screen Measuring Instrument Adjustment Page Adjustment Address 8A, 8B Specified Value The LCD screen should not be colored.

  • Page 51: Mechanism Section Adjustment

    DCR-IP210/IP210E/IP220/IP220E COVER COVER 2-3. TAPE PATH ADJUSTMENT 6-2. MECHANISM SECTION The lens block (CD-406 board) must be connected when performing ADJUSTMENT the adjustment. On the mechanism section adjustment 1. Preparation for Adjustment For detail of mechanism section adjustments, checks, and...

  • Page 52: Video Section Adjustment

    DCR-IP210/IP210E/IP220/IP220E COVER COVER 6-3. VIDEO SECTION ADJUSTMENT NTSC model: DCR- IP210/IP220 PAL model: DCR- IP210E/IP220E 3-1. PREPARATIONS BEFORE ADJUSTMENTS Use the following measuring instruments for video section adjustments. 3-1-1. Equipment to Required TV monitor Oscilloscope (dual-phenomenon, band width above 30 MHz with delay mode) (Unless specified otherwise, use a 10 : 1 probe.)

  • Page 53: Precautions On Adjusting

    DCR-IP210/IP210E/IP220/IP220E 3-1-2. Precautions on Adjusting 8) To separate the DI-087 board from the VC-308 board, Note1: Before performing the adjustments, check the data of page: 0, disconnect the following connectors. address: 10 is “00”. If not, set data: 00 to this address.

  • Page 54: Adjusting Connectors

    DCR-IP210/IP210E/IP220/IP220E 3-1-3. Adjusting Connectors Some of the adjusting points of the video section are concentrated at VC-308 board CN452. The following table lists the pin numbers and signal names of CN452. CN452 of VC-308 board Pin No. Signal Name Pin No.

  • Page 55: Alignment Tapes

    DCR-IP210/IP210E/IP220/IP220E 3-1-5. Alignment Tapes Use the alignment tapes shown in the following table. Use tapes specified in the signal column of each adjustment. Name Tracking (XH8-1) Tape path adjustment SW V&A Switching position (XH8-2 (NTSC), XH8-3 (PAL)) adjustment Fig. 6-3-3 shows the 75% color bar signals recorded on the alignment tape SW V&A.

  • Page 56: System Control System Adjustment

    DCR-IP210/IP210E/IP220/IP220E COVER COVER 3-2. SYSTEM CONTROL SYSTEM ADJUSTMENT 3. Serial No. Input Write the serial No. and model code in the EEPROM (nonvolatile memory). Convert the serial No. on the name plate from decimal to 1. Initialization of 4, 8, 9, A, B, C, D, E, F, 1B, 1E, 1F hexadecimal, and write in the EEPROM.
  • Page 57 DCR-IP210/IP210E/IP220/IP220E Hexa- Hexa- Hexa- Hexa- Hexa- Hexa- Hexa- Hexa- Decimal Decimal Decimal Decimal Decimal Decimal Decimal Decimal decimal decimal decimal decimal decimal decimal decimal decimal 0000 8192 2000 16384 4000 24576 6000 32768 8000 40960 A000 49152 C000 57344 E000...

  • Page 58: Servo And Rf System Adjustment

    Data of page: 3, address: 0B Note1: The lens block (CD-406 board) must be connected when performing the adjustments. Measuring Instrument Adjustment remote commander Note2: NTSC model: DCR-IP210/IP220 Adjustment Page PAL model: DCR-IP210E/IP220E Adjustment Address 10 to 13, 1A to 1C, 1F, 2E...

  • Page 59: Treel Fg Duty Adjustment (Vc-308 Board)

    DCR-IP210/IP210E/IP220/IP220E 2. Treel FG Duty Adjustment (VC-308 Board) 3. Read Clock fo Adjustment (VC-308 Board) Set the Treel FG signal duty cycle to 50%. Set the read clock center frequency of IC801. Mode CUE mode without a cassette Mode Play back mode without a cassette...

  • Page 60: Switching Position Adjustment (Vc-308 Board)

    DCR-IP210/IP210E/IP220/IP220E 4. Switching Position Adjustment (VC-308 Board) 5. XREC ACT Adjustment (VC-308 Board) Adjust the phase of the SWP signal (Switching pulse of the play Adjust the phase of the XREC ACT signal (Switching pulse of the back head). recording head).

  • Page 61: Timing Atf Center Value Adjustment (Vc-308 Board)

    DCR-IP210/IP210E/IP220/IP220E 6. Timing ATF Center Value Adjustment 7. AGC Adjustment and AEQ & LMS Adjustment (VC-308 Board) Note: The following adjustments should be carried out upon completion of “Switching Position Adjustment”. And perform “Timing ATF Adjustment is performed to get the data for ATF servo.

  • Page 62: Agc Adjustment (Vc-308 Board)

    DCR-IP210/IP210E/IP220/IP220E 7-2. AGC Adjustment (VC-308 Board) 7-3. Pch AEQ & LMS Adjustment (VC-308 Board) Adjust the AGC of IC801. Adjust the equalizer to minimize the Pch error rate. Mode Playback Mode Playback Signal Recorded signal at “Preparations Signal Recorded signal at “Preparations Before Adjustments”...

  • Page 63: Mch Aeq & Lms Adjustment (Vc-308 Board)

    DCR-IP210/IP210E/IP220/IP220E 7-4. Mch AEQ & LMS Adjustment (VC-308 Board) 8. Error Rate Check (VC-308 Board) Adjust the equalizer to minimize the Mch error rate. Mode Playback Mode Camera recording and play back Signal Recorded signal at “Preparations Subject Arbitrary Before Adjustments”...

  • Page 64: Video System Adjustments

    A/V jack (75Ω terminated) Measuring Instrument Oscilloscope Note1: The lens block (CD-406 board) must be connected when performing the adjustments. Adjustment Page Note2: NTSC model: DCR-IP210/IP220 Adjustment Address PAL model: DCR-IP210E/IP220E Specified Value A = 714 ± 14mV (NTSC) Switch setting: A = 700 ±...

  • Page 65: S Video Out Chroma Level Adjustment

    DCR-IP210/IP210E/IP220/IP220E 3. S VIDEO OUT Chroma Level Adjustment 4. VIDEO OUT Y, Chroma Level Check (VC-308 Board) (VC-308 Board) Mode Camera Mode Camera Subject Arbitrary Subject Arbitrary Measurement Point Chroma signal terminal of S VIDEO Measurement Point Video terminal of VIDEO plug of A/V plug of A/V jack (75Ω...

  • Page 66: Audio System Adjustments

    DCR-IP210/IP210E/IP220/IP220E COVER COVER 3-5. AUDIO SYSTEM ADJUSTMENTS Switch setting: POWER ................VCR VIDEO INPUT (Menu setting) ........VIDEO [Connection of Audio System Measuring Devices] Connect the audio system measuring devices as shown in Fig. 6- 3-9. Note: In recording mode, input a color bar signal to the video input.

  • Page 67: Overall Level Characteristics Check

    DCR-IP210/IP210E/IP220/IP220E 1. Overall Level Characteristics Check 3. Overall Noise Level Check Mode Recording and playback Mode Recording and playback Signal 400Hz, –7.5dBs signal: Signal No signal: AUDIO L and AUDIO R terminal of AUDIO L and AUDIO R terminal of...

  • Page 68: Service Mode

    DCR-IP210/IP210E/IP220/IP220E COVER COVER 6-4. SERVICE MODE 4-1. ADJUSTMENT REMOTE COMMANDER 2. Precautions upon using the adjustment remote commander The adjustment remote commander is used for changing the Mishandling of the adjustment remote commander may erase the calculation coefficient in signal processing, EVR data, etc. The correct adjustment data at times.

  • Page 69: Data Process

    DCR-IP210/IP210E/IP220/IP220E COVER COVER 4-2. DATA PROCESS The calculation of the DDS display and the adjustment remote commander display data (hexadecimal notation) are required for obtaining the adjustment data of some adjustment items. In this case, after converting the hexadecimal notation to decimal notation, calculate and convert the result to hexadecimal notation, and use it as the adjustment data.

  • Page 70: Service Mode

    DCR-IP210/IP210E/IP220/IP220E COVER COVER 4-3. SERVICE MODE Note: Before performing the adjustments, check the data of page: 0, address: 10 is “00”. If not, set data: 00 to this address. 1. Setting the Test Mode Page D Address 10 Data Function...

  • Page 71: Msw Code

    DCR-IP210/IP210E/IP220/IP220E 2-2. MSW Code MSW when errors occur: Information on MSW (mode SW) when errors occur MSW when movement starts: Information on MSW when movements starts when the mechanism position is moved (When the L motor is moved) MSW of target of movement:...

  • Page 72: Bit Value Discrimination

    DCR-IP210/IP210E/IP220/IP220E 3. Bit value discrimination Bit values must be discriminated using the display data of the Display on the Bit values adjustment remote commander for following items. Use the table adjustment bit3 bit2 bit1 bit0 below to discriminate if the bit value is “1” or “0”.

  • Page 73: Switch Check (3)

    DCR-IP210/IP210E/IP220/IP220E 6. Switch check (3) Page 3 Address F5 Note: The data of page: 0, address: 10 must be “00”. Switch When bit value=00 When bit value=01 HEADPHONE jack (JK-234 board J3400) Used Not used Using method: 1) Select page: 3, address: F5.

  • Page 74: Record Of Use Check (1)

    DCR-IP210/IP210E/IP220/IP220E 8. Record of Use check (1) Page 7 Address A7 to A9 Note1: When replacing the drum assembly or the mechanism deck, initialize the data of address: A7 to A9. Note2: This data will be kept even if the lithium battery (BT4101 of PW-2980 block) is removed.

  • Page 75: Record Of Self-Diagnosis Check

    DCR-IP210/IP210E/IP220/IP220E Ver 1.1 2003. 05 10. Record of Self-diagnosis check Page 7 Address B0 to C6 Note1: This data will be kept even if the lithium battery (BT4101 of PW- 2980 block) is removed. Note2: The data of page: 0, address: 10 must be “00”.
  • Page 76 DCR-IP210/IP210E/IP220/IP220E 〈 〉 FOR CAMERA COLOR REPRODUCTION ADJUSTMENT For NTSC model DCR-IP210/IP220 Take a copy of CAMERA COLOR REPRODUCTION FRAME with a clear sheet for use. For PAL model DCR-IP210E/IP220E 6-73E...
  • Page 77 Reverse 992999552.pdf Revision History S.M. Rev. Ver. Date History Contents issued 2002.09 Official Release — — 2003.05 Correction-1 Addition of adjustment contents S.M. correction: Page 6-72...

This manual is also suitable for:

Dcr-ip210eDcr-ip220Dcr-ip220e

Table of Contents