Hall Adjustment; Ccd Output 2Ch Matching Adjustment (1) - Sony DCR-IP210 Adjustment

3. HALL Adjustment

For detecting the position of the lens iris and ND filter, adjust AMP
gain and offset.
Subject Not required
Measurement Point Display data of page 1 (Note1)
Measuring Instrument Adjustment remote commander
Adjustment Page F
Adjustment Address 13 to 18
Specified Value 1 D6 to DA
Specified Value 2 26 to 2A
Specified Value 3 D6 to DA
Specified Value 4 26 to 2A
Note1: Displayed data of page 1 of the adjustment remote commander.
1 : XX : XX
Note2: The data of page: 0, address: 10 must be "00".
Switch setting:
POWER .................................................................. CAMERA
Adjusting method:
Order Page Address Data
1 0 01 01
2 6 01 6D
3 6 02
4 6 01 00
Note3: The adjustment data will be automatically input to page: F, address:
13 to 18.
Checking method:
Order Page Address Data
1 0 03 03
2 6 01 01
3 6 01 03
4 1
5 6 01 01
6 1
7 6 01 6B
8 6 01 69
9 1
10 6 01 6B
11 1
IRIS display data
ND display data
Procedure
Set the data.
Set the data, and press PAUSE
button.
Check that the data changes to
"01". (Note3)
Set the data, and press PAUSE
button.
Procedure
Set the data.
Set the data, and press PAUSE button.
Set the data, and press PAUSE button.
Check that the IRIS display data
(Note1) satisfies the specified
value 1.
Set the data, and press PAUSE button.
Check that the IRIS display data
(Note1) satisfies the specified
value.2.
Set the data, and press PAUSE button.
Set the data, and press PAUSE button.
Check that the ND display data
(Note1) satisfies the specified
value 3.
Set the data, and press PAUSE button.
Check that the ND display data
(Note1) satisfies the specified
value 4.
DCR-IP210/IP210E/IP220/IP220E
Processing after Completing Adjustments:
Order Page Address Data
1 6 01
2 0 03
3 0 01

4. CCD Output 2ch Matching Adjustment (1)

Correct the dispersion of the black level between the left-right
channels of the CCD imager.
Subject
Adjustment Page
Adjustment Address
Note1: This adjustment should be carried out upon completion of the
following adjustments.
"HALL Adjustment"
Note2: If this adjustment has been performed, the following adjustments
need to be performed again.
"CCD Output 2ch Matching Adjustment (2)", "Flange Back
Adjustment", "Color Reproduction Adjustment"
Note3: The data of page: 0, address: 10 must be "00".
Note4: Check that the data of page: 6, address: 02 is "00". If not, to page:
6, address: 01, set data: 00, and press the PAUSE button.
Switch setting:
1) POWER .................................................................. CAMERA
2) NIGHT SHOT .................................................................. OFF
Adjusting method:
Order Page Address Data
1 0 01
2 6 01
3 6 02
Note4: The adjustment data will be automatically input to page: F, address:
24 to 27.
Processing after Completing Adjustments
Order Page Address Data
1 6 01
2
6-23
Procedure
00 Set the data, and press PAUSE
button.
00 Set the data.
00 Set the data.
Arbitrary
F
24 to 27
Procedure
01 Set the data.
F3 Set the data, and press PAUSE
button.
Check that the data changes to
"01". (Note4)
Procedure
00 Set the data, and press PAUSE
button.
Perform "CCD Output 2ch
Matching Adjustment (2)".