Table of Contents
Advertisement
Programming
P
o r t
E
n a b l e M a s k
X
2 3
X X X X
1
1 1
23
Parameter No.
Bits
Display Units
Read/Write
Parameter Type
111
Factory Default
0/7
Min/Max Value
N/A
Drive Units
S
t a r t
S
t o p O w n e r
2 4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
24
Parameter No.
Bits
Display Units
Read Only
Parameter Type
N/A
Factory Default
N/A
Min/Max Value
N/A
Drive Units
o m m a
d S t a t u s
C
n
0
0 0 0 0
0
0 1
2 5
25
Parameter No.
Bits
Display Units
Read Only
Parameter Type
N/A
Factory Default
N/A
Min/Max Value
N/A
Drive Units
L
o g i c
S t a t u s
0
0 0 0 0
0
0 0
2 6
26
Parameter No.
Bits
Display Units
Read Only
Parameter Type
N/A
Factory Default
N/A
Min/Max Value
N/A
Drive Units
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Port Enabled Mask
This parameter sets the ability of a SCANport device to issue enable commands. The
commands are defined by the first (3) bits of a 16 bit word. The [Port Enable Mask] may be set
while the 1336 REGEN Converter is enabled.
Bit 2
Bit 1 Bit 0
0 = Autoenable Not Allowed
0 = SCANport 1 Enable Not Allowed
0 = SCANport 2 Enable Not Allowed
Bit 0 = 1 When Bit 0 =1, the system will be set to the auto-enable mode.
Bit 0 = 0 When Bit 0 = 0, this input requires an enable command from SCANport 1 or 2.
Start/Stop Owner
This parameter displays which adapter is currently issuing a valid enable command. Only the
first (3) bits of each byte are valid.
Bit 10 Bit 9 Bit 8
Bit 2
Bit 1
Current Command Being Issued
This parameter displays the logic command currently being issued.
Bit15
Bit3
Bit 1 Bit 0
Logic Status
This parameter displays the current logic status of the 1336 REGEN Converter.
Bit 7
Bit 1 Bit 0
Regenerative Brake Operation
1 = Autoenable Allowed
1 = SCANport 1 Enable Allowed
1 = SCANport 2 Enable Allowed
Bit 0
0 = Digital Input Enable Present
0 = SCANport 1 Stop Not Present
0 = SCANport 2 Stop Not Present
0 = Digital Input Enable Not Present
0 = SCANport 1 Start Not Present
0 = SCANport 2 Start Not Present
0 = Stop Command Inactive
0 = Enable Command Inactive
0 = Clear Fault Command Inactive
0 = Reset Command Not Present
0 = Converter Not Ready
0 = Converter Not Enabled
0 = Converter Not Faulted
3–39
1 = Digital Input Enable Not Presen
1 = SCANport 1 Stop Present
1 = SCANport 2 Stop Present
1 = Digital Input Enable Present
1 = SCANport 1 Start Present
1 = SCANport 2 Start Present
1 = Stop Command Active
1 = Enable Command Active
1 = Clear Fault Command
1 = Reset Command Present
1 = Converter Ready
1 = Converter Enabled
1 = Converter Faulted
Advertisement
Table of Contents
