Mounting, Dismounting & Transportation; Placing Foreign Objects Into The Unit; Preventive Maintenance - JCM GLOBAL DBV Series Integration Manual

4. Avoid exposing the Banknote Insertion Slot to
direct Sunlight and/or Incandescent Lamp
illumination having a Gradient Angle of 15
Degrees or more, and an illumination index of
3000 Lux or less. Insure that the Host Machine is
also designed to avoid exposing the Banknote
Insertion Slot to direct Sunlight or incandescent
light.
5. Do not allow the Validator to endure a range of
temperature and humidity beyond the environ-
mental limits specified (See "Environmental
Specifications" on page 6 of this Section).
6. Do not use the Validator in environments that
may be subject to severe temperature changes.
7. Do not use the Validator where it may be exposed
to airborne evaporated or sporadic chemicals.
8. Clean and maintain the Validator regularly when
located in an excessively smoke filled environ-
ment.
9. Do not throw or apply excessive force to the unit.
Mounting, Dismounting & Transportation
Methods for mounting, dismounting and transport-
ing the unit:
1. Be sure to turn the Power OFF before mounting
or removing the Unit from its permanent location.
Plugging or unplugging Connector Plugs from
their receptacles while the Power is ON may
cause damage to the Unit.
2. When reassembling a disassembled Unit Part,
ensure that the each part is properly replaced in its
correct original location and the Validator is not
removed by pulling it forward.
3. Be sure to carry the Unit by both hands when
transporting it. Holding the Unit by one hand may
cause personal injury if the Unit accidentally
becomes disassembled and drops away.
4. Be careful not to use excessive outside pressure
on the Unit, or subject it to excessive vibration
during transportation.

Placing Foreign Objects into the Unit

Observe the following precautions when placing
foreign objects into the Unit:
1. Do not insert anything except Banknotes into the
Insertion Slot. Inserting Receipts, Stapled Tickets,
Rubber Bands, or Credit Cards into the Unit may
damage the Banknote Transport path.
2. Do not inject liquids into the Banknote Insertion
Slot. Injecting water, oil or cleaning agents may
damage the Sensors or plastic parts within the
Banknote Transport path.
P/N 960-000175R_Rev. A {EDP #233426}
®
DBV Series Banknote Validator (DBV-400) Integration Guide

Preventive Maintenance

The preventive maintenance requirements are
defined as follows:
1. When attaching the Cash Box to the DBV-400
Unit, ensure that it clicks firmly into place. Do
not redesign or disassemble the DBV-400 Valida-
tor. Unauthorized use by inadequately trained per-
sonnel, or use outside the original manufacturer's
intent for operation voids the warranty.
WARNING: Do not inject water or other
liquid agents of any kind into the
Validator, as this may cause extreme
damage to the Unit.
2. Do not redesign or disassemble the DBV-400 Val-
idator. Unauthorized use by inadequately trained
personnel, or use outside the original manufac-
turer's intent for operation voids the warranty
3. Perform routine cleaning and maintenance at least
once a month to keep the DBV-400 Unit's perfor-
mance stable.
4. Use a soft, lint-free, Micro-fiber Cloth, cotton
swab or non-flammable compressed air spray to
clean dust and debris from the Rollers.
WARNING: Do not use flammable
compressed air spray, as this may
cause fire.
WARNING: To minimize risk of damage
to internal printed circuit boards, never
allow excess fluid (e.g., from a wet
cleaning cloth) to drip or leak into the
device. Internal printed circuit boards
may be damaged. Do not use any
alcohol, citrus based cleaners,
solvents, surface acting agents or
scouring agents that can damage the
plastic surfaces of the device.
5. If the Unit is exposed to water or other liquids,
use a clean, dry Micro-fiber Cloth to wipe off and
absorb excess liquids immediately. Any remain-
ing liquids or fluids may affect and degrade the
Sensors and Validation component performance.
Caution: Make sure Interface Harness
connections to the Host Machine are
shorter than 9.84 Feet (3 Meters) in
length. Cut off all unused portions of
the Interface Harness wiring to avoid
static electrical effects or short circuit
possibilities that could cause damage
to the Unit.
WARNING: This Unit is designed for
use with a Current limiting Power
Source! Design the Host Cabinet space
to meet all local related safety
standards.
© 2014, JAPAN CASH MACHINE CO., LTD.
3