Setting The Resolution Of Your Coronis Display Panel With Dualview Enabled - Barco Coronis 5MP System Manual

Setting the Resolution of Your CORONIS Display Panel with Setting the Resolution of Your CORONIS Display Panel with Setting the Resolution of Your CORONIS Display Panel with
Setting the Resolution of Your CORONIS Display Panel with Setting the Resolution of Your CORONIS Display Panel with
DualView enabled DualView enabled DualView enabled
DualView enabled DualView enabled
Once you have completed the installation of the separate screens with
DualView, you need to set the resolution for each display. Both
screens of each display controller cannot be enabled at the same time
unless their display properties match.
1. To set the resolution for your CORONIS display panel(s) under
DualView, right click on the desktop and select "Properties"
2. Select the "Settings"
select the rect
attached to the BarcoMed Display Controller you are working with.
SPECIAL SPECIAL
SPECIAL NOTE: SPECIAL SPECIAL
BarcoMed Display Controller, the resolution for the first display will
still be set to a VGA resolution of "640 x 480" pixels. If the
BarcoMed Display Controller is not running VGA, the display may
not be enabled yet. To enable the device check
W W W W W indows desktop onto this monitor"
"Apply" "Apply"
"Apply" button at this time. "Apply" "Apply"
If necessary detach the second display of the BarcoMed Display
Controller you are working with by right clicking on the rectangle
that represents it and deselect "Att
button.
Note: Since Windows 2000 will not let you detach the primary Note: Note:
Note: Note:
display, you may need to temporarily make another display the
primary display.
3. For the display which is still attached click on the "Advanced"
Button.
4. Select the "Adapter"
button. Select the resolution and refresh rate that your CORONIS
display panel supports from the dialog box and click "OK"
Note: Note: Note: Note: In the Adapter box, the Adapter string shows if this display is Note:
the First View or the Second View attached to the display
controller. Please make a note of this, so that you can arrange the
displays in the correct order later.
5. Click "OK"
"OK" button on the bottom of the Adapter Control Panel is not "OK" "OK"
"OK" "OK"
visible, press "CTRL"+"Enter"
6. Click "OK"
settings" dialog box. Your high resolution display(s) should now
synchronize and display the Windows desktop.
7. Click "Y "Y "Y "Y "Yes"
Do you want to keep these settings?"
System manual Coronis 5MP
"Settings" "Settings" tab (see figure 58on the next page). Now "Settings" "Settings"
rect rect angle angle
rect rectangle angle that represents the first CORONIS display angle
NOTE: NOTE:
NOTE: If you are using the VGA capabilities of your NOTE:
indows desktop onto this monitor" indows desktop onto this monitor" checkbox. Do not click the indows desktop onto this monitor" indows desktop onto this monitor"
"Adapter" "Adapter" tab and then click on the "List "Adapter"
"Adapter"
"OK" "OK"
"OK" "OK" on the bottom of the Adapter Control Panel. If the
"CTRL"+"Enter" "CTRL"+"Enter" "CTRL"+"Enter" to select "OK"
"CTRL"+"Enter"
"OK" in the "Windows will now apply your new desktop "OK" "OK"
"OK"
es" when asked, "Your desktop has been reconfigured. es" es" es"
BarcoMed software driver installation
check the "Extend my check check check
"Att "Att ached" ached"
"Attached" "Att ached" ached". Click the "Apply"
"OK" "OK". "OK"
"OK"
"Properties" "Properties"
"Properties" "Properties".
"Extend my "Extend my "Extend my "Extend my
"Apply" "Apply"
"Apply" "Apply"
"Advanced" "Advanced" "Advanced" "Advanced"
"List "List "List All Modes..." All Modes..." All Modes..." All Modes..."
"List All Modes..."
"OK" "OK" "OK" "OK".
83