Featuring the industry’s first 30-inch color LCD that can be used as two seamless heads or one wide-screen display, Coronis Fusion 4MP / 6MP offers you the freedom to organize your workspace just the way you want it. It allows you to read CT, MR, cath and echo cardiogram images, or any other combination, side by side on a single diagnostic screen.
Standby key Power LEDs Ambient light sensor The key icons are displayed above the keys, adapted to the function that it is used for (menu dependent). See "Navigating through the OSD menus", page 19. K5902108 CORONIS FUSION 4MP / 6MP 23/11/2016...
Connector compartment cover +24 VDC power input Neck cover Display stand cover DisplayPort 2 video input DVI 2 video input DisplayPort 1 video input DVI 1 video input USB upstream connector USB downstream connectors K5902108 CORONIS FUSION 4MP / 6MP 23/11/2016...
3. Display installation 3. DISPLAY INSTALLATION Prior to installing your Coronis Fusion 4MP / 6MP and connecting all necessary cables, make sure to have a suitable display controller physically installed in your computer. If you are using a Barco display controller, please consult the user guide delivered with it to do this.
To remove the hook: 1. Position the display with its rear side facing you. 2. While holding the display panel pushed down, pull out the red hook in the display stand. K5902108 CORONIS FUSION 4MP / 6MP 23/11/2016...
Adjusting the display position Now that the height-positioning system of your display is unlocked, you can adjust the display position. To adjust the display position 1. Tilt, swivel, raise and lower the display as desired. K5902108 CORONIS FUSION 4MP / 6MP 23/11/2016...
3. If you want to make use of your display’s USB downstream connectors, connect a PC USB downstream connector to the display’s USB upstream connector by means of the supplied USB 2.0 cable. K5902108 CORONIS FUSION 4MP / 6MP 23/11/2016...
2. Plug the other end of the external DC power supply into a grounded power outlet by means of the proper power cord delivered in the packaging. Routing the cables To route the cables 1. Route all connected cables through the cable routing channel in the stand of your display. K5902108 CORONIS FUSION 4MP / 6MP 23/11/2016...
To re-attach the connector compartment cover 1. Slide the cover’s top in position and then push the cover’s bottom. You’ll hear a “click” sound of the cover’s clips when the connector compartment cover is in position. K5902108 CORONIS FUSION 4MP / 6MP 23/11/2016...
VESA. This chapter shows you how to release the panel from the stand and how to attach it to an arm. If you’re not using an arm, you can skip this chapter. 1. Gently pull open both lower sides of the cover. K5902108 CORONIS FUSION 4MP / 6MP 23/11/2016...
First time starting up Overview You are now ready to start up your Coronis Fusion 4MP / 6MP for the first time. 1. Switch on your Coronis Fusion 4MP / 6MP as described in "Standby switching", page 18. 2. Turn on the computer connected to your display.
Page 17
finished. Your Coronis Fusion 4MP / 6MP display will be running in a basic video mode at a de- fault refresh rate when first time starting up. If you are using a Barco display controller, please consult the dedicated user guide available on the system CD to install the drivers, software and documentation.
LCD displays use technology based on pixels. As a normal tolerance in the manufacturing of the LCD, a limited number of these pixels may remain either dark or permanently lit, without affecting the diagnostic performance of the product. To ensure optimal product quality, Barco applies strict selection criteria for its LCD panels.
The ’MediCal QAWeb’ system offers online service for high-grade Quality Assurance, providing maximum diagnostic confidence and uptime. Barco recommends to install MediCal QAWeb Agent and apply the default QAWeb policy at least. This policy includes calibration on regular intervals. Connecting to MediCal QAWeb Server offers even more possibilities.
How to bring up the OSD menus The OSD menu allows you to configure different settings to make your Coronis Fusion 4MP / 6MP fit your needs within your working environment. Also, you can retrieve general information about your display and its current configuration settings through the OSD menu.
About the OSD menu language By default, the OSD menu comes up in English. However, there’s a wide range of other languages avail- able for the OSD menu of your Coronis Fusion 4MP / 6MP. To change the language of the OSD menu: 1.
About the power lock function By enabling the power lock function, the Coronis Fusion 4MP / 6MP is forced to remain switched on. This means that it can’t be switched to stand-by mode manually until the power lock function is disabled again.
Luminance target About the luminance target The luminance target of your Coronis Fusion 4MP / 6MP is adjustable over a predefined range. When you change the luminance target, the display will adjust its backlight to reach the target. K5902108 CORONIS FUSION 4MP / 6MP 23/11/2016...
2. Navigate to the Configuration > Calibration > Color Settings menu. 3. Enter the Color Definition submenu. 4. Select Color Temperature and confirm. 5. Enter the Color Temperature submenu. 6. Set the Temperature value as desired and confirm. K5902108 CORONIS FUSION 4MP / 6MP 23/11/2016...
To quickly switch the viewing mode without having to enter the OSD menu, touch the left and right key (the two leftmost buttons) at the same time during normal operation. The diagnostic mode should always be selected when the Coronis Fusion 4MP / 6MP is intended to be used in a diagnostic environment.
DICOM: DICOM (Digital Imaging and Communications in Medicine) is an international standard that was developed to improve the quality and communication of digital images in radiology. In short, the DICOM display function results in more visible grayscales in the images. Barco recommends selecting the DICOM display function for most medical viewing applications.
DICOM display function when Ambient Light Compensation (ALC) is enabled. Please refer to "Ambient Light Compensation (ALC)", page 26 to enable ALC. The available reading rooms for your Coronis Fusion 4MP / 6MP are: •...
Embedded QA is not a replacement for the Barco MediCal QAWeb solution. Although Embedded QA is a reliable option to perform a simple calibration or compliance test, Barco still highly recommends MediCal QAWeb as the solution of choice for calibration and QA. Medical QAWeb brings many benefits such as centralized asset management, the ability to schedule tasks, remote man-...
The DICOM calibration will add a correction to the current DICOM curve to approach the perfect DICOM curve as well as possible. To start DICOM calibration: 1. Bring up the OSD main menu. 2. Navigate to the Configuration > Calibration > Embedded QA menu. K5902108 CORONIS FUSION 4MP / 6MP 23/11/2016...
To enable/disable image scaling: 1. Bring up the OSD main menu. 2. Navigate to the Configuration > Image Source menu. 3. Enter the Scaling submenu. 4. Select Enabled/Disabled as desired and confirm. K5902108 CORONIS FUSION 4MP / 6MP 23/11/2016...
5.19 Image source selection modes About image source selection modes Your Coronis Fusion 4MP / 6MP automatically detects the number of video input signals connected, at- taches them to the correct display side and applies the correct video settings to it (resolution, video encod- ing mode, refresh rate,...).
4. Select one of the available connectors/inputs and confirm. 5.21 Grayscale conversion modes Your Coronis Fusion 4MP / 6MP display automatically detects the connected video in- put signals and applies the correct grayscale conversion settings. Manually selecting a grayscale conversion mode is possible, but then your display’s image source selection mode should be set to allow this.
4. Select one of the available color conversion modes and confirm. 5.22 EDID format About EDID format The Coronis Fusion 4MP / 6MP supports two EDID formats: E-EDID V1.4 and DisplayID V1.3 To select the EDID format 1. Bring up the OSD main menu.
To retrieve the status of your display: 1. Bring up the OSD main menu. 2. Navigate to the Status menu. 3. Enter the Display, Image Sources, Calibration or Connectivity submenu as desired. K5902108 CORONIS FUSION 4MP / 6MP 23/11/2016...
LCD. Do not apply or spray liquid directly to the display as excess liquid may cause AUTION damage to internal electronics. Instead, apply the liquid to a cleaning cloth. K5902108 CORONIS FUSION 4MP / 6MP 23/11/2016...
3. Place the bottom buffer in the box. 4. Put the power supply in the dedicated cavity of the bottom buffer. 5. Put the Coronis Fusion 4MP / 6MP display in its original bag and place it in the box with its panel facing downwards.
The equipment should be installed near an easily accessible outlet. • The equipment is intended for continuous operation. Transient over-voltage If the device is not used for a long time, disconnect it from the AC inlet to avoid damage by transient over-voltage. K5902108 CORONIS FUSION 4MP / 6MP 23/11/2016...
Please dispose of your waste equipment by handing it over to a designated collection point for the K5902108 CORONIS FUSION 4MP / 6MP 23/11/2016...
Page 43
Electronic Products ” (Also called RoHS of Chinese Mainland), the table below lists the names and contents of toxic and/or hazardous substances that Barco’s product may contain. The RoHS of Chinese Mainland is included in the MCV standard of the Ministry of Information Industry of China, in the section “Limit Requirements of toxic substances in Electronic Information Products”.
Mainland, marked with the Environmental Friendly Use Period (EFUP) logo. The number inside the EFUP logo that Barco uses (please refer to the photo) is based on the “General guidelines of environ- ment-friendly use period of electronic information products” of Chinese Mainland.
Electromagnetic emissions The Coronis Fusion 4MP / 6MP is intended for use in the electromagnetic environment specified below. The customer or the user of the Coronis Fusion 4MP / 6MP should assure that it is used in such an envi- ronment.
Page 46
Electromagnetic immunity The Coronis Fusion 4MP / 6MP is intended for use in the electromagnetic environment specified below. The customer or the user of the Coronis Fusion 4MP / 6MP should assure that it is used in such an envi- ronment.
Page 47
RF transmitters, an electromagnetic site survey should be considered. If the measured field strength in the location in which the Coronis Fusion 4MP / 6MP is used exceeds the applicable RF compliance level above, the Coronis Fusion 4MP / 6MP should be observed to verify normal operation.
The Coronis Fusion 4MP / 6MP is intended for use in an electromagnetic environment in which radiated RF disturbances are controlled. The customer of the user of the Coronis Fusion 4MP / 6MP can help prevent electromagnetic interference by maintaining a minimum distance between portable and mobile RF communications equipment (transmitters) and the Coronis Fusion 4MP / 6MP as recommended below, according to the maximum output power of the communications equipment.
Page 49
Indicates the manufacturing date Indicates the temperature limitations for the device to safely operate within specs Indicates the device serial number 10. Values for xx and yy can be found in the technical specifications paragraph. K5902108 CORONIS FUSION 4MP / 6MP 23/11/2016...
Page 50
Indicates the maximum number of boxes to be stacked on each other. Indicates that the box should be carried with two persons. 20 - 30 Kg K5902108 CORONIS FUSION 4MP / 6MP 23/11/2016...
Barco software products are the property of Barco. They are distributed under copyright by Barco NV or Barco Inc., for use only under the specific terms of a software license agreement between Barco NV or Barco Inc. and the licensee. No other use, duplication, or disclosure of a Barco software product, in any form, is authorized.
OSD languages English, German, French, Dutch, Spanish, Italian, Portuguese, Polish, Russian, Swedish, Chinese (simplified), Japanese, Korean, Arabic Dimensions with stand (W Portrait: N/A x H x D) Landscape: 731 x 528~628 x 259 mm K5902108 CORONIS FUSION 4MP / 6MP 23/11/2016...
Page 53
0 °C to 35 °C (15 °C to 30 °C within specs) Storage temperature -20°C to 60°C Operating humidity 8% to 80% (non-condensing) Storage humidity 5% to 85% (non-condensing) Operating pressure 70 kPa minimum Storage pressure 50 to 106 kPa K5902108 CORONIS FUSION 4MP / 6MP 23/11/2016...
Page 54
Dimensions with stand (W Portrait: N/A x H x D) Landscape: 731 x 528~628 x 259 mm Dimensions w/o stand (W Portrait: N/A x H x D) Landscape: 731 x 485 x 140 mm K5902108 CORONIS FUSION 4MP / 6MP 23/11/2016...
Page 55
0 °C to 35 °C (15 °C to 30 °C within specs) Storage temperature -20 °C to 60 °C Operating humidity 8% to 80% (non-condensing) Storage humidity 5% to 85% (non-condensing) Operating pressure 70 kPa minimum Storage pressure 50 to 106 kPa K5902108 CORONIS FUSION 4MP / 6MP 23/11/2016...
Barco whatsoever. You further acknowledge that any such additions, changes or modifications may impair the ability of Barco – at Barco’s sole discretion - to continue to provide ser- vice, warranties, software updates, fixes, maintenance, access or such similar abilities, without any recourse or claim towards Barco whatsoever.