Advertisement
Quick Links
Installation Instructions For
Profile Series v.G1 Cylindrical Lock
A7755A
Copyright © 2004, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of
Sargent Manufacturing Company is prohibited.
FOR ASSISTANCE, CONTACT SARGENT AT 800-727-5477 or www.sargentlock.com
A7755A.indd 1
11/9/18 12:05 PM
Advertisement
Related Manuals for Assa Abloy Sargent Profile G1 Series
Summary of Contents for Assa Abloy Sargent Profile G1 Series
- Page 1 Installation Instructions For Profile Series v.G1 Cylindrical Lock A7755A Copyright © 2004, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
-
Page 2: Table Of Contents
Table of Contents Page Warning General Description ............1 Specifications ..............1 Features ................1 Parts Breakdown ...............2-3 Installation Instructions ............4-9 Operational Check ............. 10 Installation of RF Technology Lock (G1-TU, G1-TA, G1-TP) Warning Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. -
Page 3: General Description
Profile Series v.G1 Cylindrical Lock General Description The SARGENT Keypad Cylindrical Lock is designed for areas which require stand alone authorized entry. It is a self-contained microprocessor-controlled keypad with non-volatile memory. The keypad will hold a total of 100(LK)/2000 (G1-LU, G1-PK, G1-PA, G1-TU, G1-TP, G1-TA) different user codes. User codes “01” & “02” are utilized for Master Code and Supervisory Code, respectively. -
Page 4: Parts Breakdown
Profile Series v.G1 Cylindrical Lock Parts Breakdown 18, 24 Optional 800-810-WIRE (9473) • www.sargentlock.com • A7755A A7755A.indd 2 11/9/18 12:05 PM... - Page 5 Profile Series v.G1 Cylindrical Lock Parts Breakdown (Continued) ITEM PART No. DESCRIPTION REQ’D 10-2000 2-3/4” Backset Latch (Standard) 10-2053 3-3/4” Backset Latch (23 Prefix) 10-2058 5” Backset Latch (25 Prefix) 10-2634 3/4” Throw (41 Prefix) 10-3026 Outside Escutcheon Key Pad, Key Pad/Prox (LK) 10-3130 Outside Escutcheon Key Pad, Key Pad/Prox (G1-LU, G1-PK, G1-TU, G1-TP) 10-3131...
-
Page 6: Installation Instructions
Profile Series v.G1 Cylindrical Lock Installation Instructions 1. Verify Hand and Bevel of Door Verify hand and bevel of door Stand on outside/locked side of the door when determining the door hand Left Hand Left Hand Right Hand Right Hand Hinges Left. - Page 7 Profile Series v.G1 Cylindrical Lock 3. Frame Preparation for Strike Centerline of latch front and strike Screws (2) #8-32 x 3/4” 4. Latchbolt and Fire Stop Plate Installation 1. Install latch with beveled bolt facing the strike. 2. Attach with two screws but DO NOT tighten completely at this time. 3.
- Page 8 Profile Series v.G1 Cylindrical Lock 5. Lock Installation Lock Preset to: • Through-bolt location– 12 & 6 o’clock • Door thickness– 1-3/4” thick- see below for other door conditions Adjustment for different through-bolt and door thickness: • Through-bolt location– rotate outside rose to match door • Door thickness– rotate outside rose to align door thickness marking with lockbody edge • Spacer bushing– remove and realign to fit into back of lever Through-bolt holes 1-3/4" thick door Spacer bushing 2" thick door Rotate to match through-bolt holes in door 1.
- Page 9 Profile Series v.G1 Cylindrical Lock 6. Securing the Lock to Door Feed wires and 1A. If wood door, feed wires up through connector in the routed channel as shown. routed channel Routed channel for 1B. If metal door, feed wire and connector wood door only through inside of door and out hole on outside of door.
- Page 10 Profile Series v.G1 Cylindrical Lock 8. Installation of Outside Escutcheon and Lever NOTE: For exterior applications, use weather seal gasket part Outside of door # (10-0649) between escutcheon and outside door surface 1A. For fire rated doors only feed ribbon cable connector and Weather seal gasket Outside...
- Page 11 Profile Series v.G1 Cylindrical Lock 11. Battery Installation Fig. 1 Battery keeper Note: For RF Technology version refer to Section 8 For RF Technology version, see Section to install battery Battery 8 to install Battery Keeper keeper. cover Battery cover Security Security screw...
-
Page 12: Operational Check
Profile Series v.G1 Cylindrical Lock Operational Check For devices with cylinders: 1. Insert key into cylinder and rotate. 2. The key will retract the latch. Key should rotate freely 3. Inside lever retracts latch and deadbolt (if provided) 4. Enter 1234* to unlock outside lever handle and retract latch and deadbolt (if provided) 5. I f lock is prox only (G1-PA) or RF Technology with Prox (G1-TA) - refer to Keypad programming instruction...