Advertisement
Quick Links
Installation Instructions For
Profile Series v.G1 Exit Device
A7757C
Copyright © 2004, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of
Sargent Manufacturing Company is prohibited.
FOR ASSISTANCE, CONTACT SARGENT AT 800-727-5477 or www.sargentlock.com
Advertisement
Related Manuals for Assa Abloy SARGENT Profile Series v.G1
Summary of Contents for Assa Abloy SARGENT Profile Series v.G1
- Page 1 Installation Instructions For Profile Series v.G1 Exit Device A7757C Copyright © 2004, 2008, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.
-
Page 2: Table Of Contents
Profile Series v.G1 Exit Device Table of Contents Page Warning General Description ................1 Specifications ..................1 Features .....................1 Parts Breakdown ................2-5 Installation Instructions–Rim Type Device ........6-9 Installation Instructions–Mortise Type Device ......10-13 Operational Check ................14 Installation of the RF Technology Lock (G1-TU, G1-TA, G1-TP)..14 Warning Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. -
Page 3: General Description
Profile Series v.G1 Exit Device General Description The SARGENT Profile Series v. G1 Rim/Mortise Exit Device is designed for areas which require stand alone authorized entry. It is a self-contained microprocessor- controlled keypad with non-volatile memory. The keypad will hold a total of 100 (LK)/2000 (GI-LU, GI-PK, GI-PA, G1-TU, G1-TP, G1-TA) different user codes. -
Page 4: Parts Breakdown
Profile Series v.G1 Exit Device Parts Breakdown 8877/8878 x ET x Lever Design Profile Series Rim Exit Device 18 (X4) 13 (X2) 13 (X2) 800-810-WIRE (9473) • www.sargentlock.com • A7757C... - Page 5 Profile Series v.G1 Exit Device ITEM PART No. DESCRIPTION REQ’D 52-2839 Outside Escutcheon (Prox Only) Assembly (G1-PA, G1-TA) 52-2474 Outside Escutcheon (Keypad Only) Assembly (LK) 52-2838 Outside Escutcheon (Keypad/Prox) Assembly (G1-LU, G1-PK, G1-TU, G1-TP) 52-2704 Key Pad and Proximity Assembly (G1-LU, G1-PK, G1-TU, G1-TP) 52-2432 Keypad/Proximity Bezel Assembly w/ Harness (LK) 52-2706...
- Page 6 Profile Series v.G1 Exit Device Parts Breakdown 8977/8978 x ET x Lever Design Profile Series Mortise Exit Device Door 19 (X4) 800-810-WIRE (9473) • www.sargentlock.com • A7757C...
- Page 7 Profile Series v.G1 Exit Device ITEM PART No. DESCRIPTION REQ’D 52-2839 Outside Escutcheon (Prox Only) Assembly (G1-PA, G1-TA) 52-2838 Outside Escutcheon (Keypad/Prox) Assembly (LK, G1-LU, G1-PK, G1-TU, G1-TP) 52-2432 Keypad/Proximity Bezel Assembly w/ Harness (LK) 52-2704 Key Pad and Proximity Assembly (LK, G1-LU, G1-PK) 52-2706 Proximity Assembly (G1-PA, G1-TA) 68-1397...
-
Page 8: Installation Instructions-Rim Type Device
Profile Series v.G1 Exit Device Installation Instructions for Rim Type Exit Device 8877/8878 IMPORTANT: BEFORE STARTING Inside • This device is non handed • Door should be fitted and hung • Verify box label for size of exit device, function and hand Left Hand Right Hand Reverse Bevel... - Page 9 Profile Series v.G1 Exit Device Installation Instructions (Continued) Step #3 – Attach Fire Stop Plate NOTE: Required for 12- Fire Rated doors only 1. Drill (2) 1/8" diameter holes if the door is not supplied with them Non Fire Rated Exterior Doors- Install Weather Conduit 2.
- Page 10 Profile Series v.G1 Exit Device Rim Installation Instructions (Continued) Step #5 Installation of Inside Escutcheon 1. Connect ground wire to terminal E3 (Fig. 1), keypad harness to controller (Fig. 2), and ET motor harness to motor connector (Fig. 3). 2. Place extra wire inside door hole and/or outside escutcheon being careful not to pinch wires. 3.
- Page 11 Profile Series v.G1 Exit Device Rim Installation Instructions (Continued) Battery keeper Note: For RF Technology versions (G1-TU, G1-TP, G1-TA) refer to Section 9 when installing/removing battery keeper. Battery cover Security screw Security tool 01-0297 included Fig. 4 1. Place (6) “AA” batteries into 2.
-
Page 12: Installation Instructions-Mortise Type Device
Profile Series v.G1 Exit Device Installation Instructions for Mortise Type Exit Device 8977/8978 Inside IMPORTANT: BEFORE STARTING • Check hand of door - this device is not reversible • Door should be fitted and hung Left Hand Right Hand Verify box label for size of exit Reverse Bevel Reverse Bevel "LHRB"... - Page 13 Profile Series v.G1 Exit Device Mortise Installation Instructions (Continued) Step #2 – Install Outside Trim, Exit Chassis and Cylinder B. Exit Chassis: 1. Route “ET” harness along track cutout for wood doors and access hole for metal doors 2. Mount exit chassis carefully. Do not pinch harness wires 3.
- Page 14 Profile Series v.G1 Exit Device Mortise Installation Instructions (Continued) Step #3 – Attach Fire Stop Plate NOTE: Required for 12- Fire Rated doors only Non Fire Rated Exterior Doors- Install Weather Conduit 1. Drill (2) 1/8" diameter holes if the door is not supplied (P/N 52-2847) as shown below with them 2.
- Page 15 Profile Series v.G1 Exit Device Mortise Installation Instructions (Continued) Step #5 – Installation of Inside Escutcheon 1. Connect ground wire to terminal E3 (Fig. 1), keypad harness to controller (Fig. 2), and ET motor harness to motor connector (Fig. 3). 2.
-
Page 16: Operational Check
Profile Series v.G1 Exit Device Operational Check 1. For devices without cylinder go to step 4 2. For devices with cylinders, insert key into cylinder and rotate 3. The key will retract the latch, the key should rotate freely 4. Depress inside rail to retract latch 5.
Need help?
Do you have a question about the SARGENT Profile Series v.G1 and is the answer not in the manual?
Questions and answers