Table of Contents
Advertisement
Grey Headline (continued)
System configuration
The IP page lets you configure the IP protocols
and settings of the VCS.
To go to the IP page
•
System configuration > IP
To configure these settings using the CLI:
xConfiguration IP
•
xConfiguration IPProtocol
•
xConfiguration Ethernet
•
You must save your changes and restart
the system for changes to take effect.
About IP protocols
You can configure the VCS to use IPv4, IPv6 or
Both protocols. The default is Both.
IPv4: the VCS only: accepts registrations from
endpoints using an IPv4 address; takes calls
between endpoints communicating via IPv4;
communicates with other systems via IPv4.
IPv6: the VCS only: accepts registrations from
endpoints using an IPv6 address; takes calls
between endpoints communicating via IPv6;
communicates with other systems via IPv6.
Both: the VCS accepts registrations from
endpoints using either an IPv4 or IPv6 address,
and takes calls using either protocol. If a call is
between an IPv4-only and an IPv6-only endpoint,
the VCS acts as an IPv4 to IPv6 gateway. It
communicates with other systems via either
protocol.
IPv4 to IPv6 gatewaying (interworking)
The VCS can act as a gateway for calls between
IPv4 and IPv6 devices. To enable this feature,
select an IP protocol of Both.
Calls for which the VCS is acting as an IPv4 to
IPv6 gateway are traversal calls and require a
traversal call license.
Overview and
System
Introduction
status
configuration
D14049.07
March 2010
Some endpoints support both IPv4 and
IPv6, but an endpoint can use only one
protocol when registering with the VCS.
Whether the endpoint uses IPv4 or IPv6 is
determined by the IP addressing scheme used
on the endpoint to specify the IP address of the
VCS. After the endpoint has registered using
either IPv4 or IPv6, the VCS only sends calls to
it using this addressing scheme. Calls made to
that endpoint from another device using the
other addressing scheme are converted
(gatewayed) by the VCS.
External LAN interface
The External LAN interface field indicates which
LAN port is connected to your external network.
It also determines the port from which TURN
server relay allocations are made.
About IP routes (static routes)
You can set the default IPv4 and IPv6 gateways
used by the VCS. These are the gateways to
which IP requests are sent for IP addresses
that do not fall within the VCS's local subnet.
However, you can also configure additional IP
routing information (static routes) on the VCS.
This is sometimes required when using the Dual
Network Interfaces option and occasionally
required in other complex network deployments.
You can configure routes for up to 50 networks
and host combinations.
IP routes can be configured using the CLI only:
xConfiguration IP Route
•
xCommand RouteAdd
•
VCS
Zones and
Clustering and
configuration
neighbors
peers
IP
About LAN configuration
LAN 1 is the primary network port on the VCS.
You can configure the IPv4 address and subnet
mask, and IPv6 address for this port. For VCS
Expressway boxes behind a static NAT, you can
also configure the NAT's IP address. If you have
Dual Network Interfaces installed, you can also
configure these options for the LAN 2 port.
The VCS is shipped with a default IP address
of 192.168.0.100 (for both LAN ports). This
lets you connect the VCS to your network and
access it via the default address so that you
can configure it remotely.
About Dual Network Interfaces
The Dual Network Interface option key enables
the LAN 2 port on the VCS Expressway for both
management and call signaling. This allows you
to have a second IP address for your VCS.
This configuration is intended for high-security
deployments where the VCS is located in a DMZ
between two separate firewalls on separate
network segments. In such deployments,
routers prevent devices on the internal network
from being able to route IP traffic to the public
internet, and instead the traffic must pass
through an application proxy such as the VCS.
To enable this feature you must purchase and
install the appropriate option key. Contact your
TANDBERG representative for information.
You should configure the LAN 1 port and
restart the VCS before configuring the
LAN 2 port.
If you have Dual Network Interfaces
enabled but only want to configure one
of the Ethernet ports, you must use
LAN 1.
Call
Bandwidth
processing
control
42
TANDBERG
VIDEO COMMUNICATION SERVER
About static NAT
It is possible to deploy a VCS Expressway
behind a static NAT device, allowing it to have
separate public and private IP addresses. This
feature is intended for use in deployments
where the VCS Expressway is located in a DMZ,
and has the Dual Network Interfaces feature
enabled (see the previous section).
In these deployments, the externally-facing
LAN port has static NAT enabled in order to
use both a private and public IPv4 address; the
internally facing LAN port does not have static
NAT enabled and uses a single IPv4 (or IPv6)
address.
In such a deployment, when configuring
traversal clients to use the VCS Expressway as
a traversal server, it is the latter internally-facing
IP address of the VCS Expressway that should
be used.
To enable the use of a static NAT:
•
ensure that the Dual Network Interfaces
option key is installed
•
on the IP page (System Configuration > IP),
for the externally-facing LAN port:
•
in the IPv4 address field, enter the VCS
Expressway's private IP address
•
select an IPv4 static NAT mode of On
•
in the IPv4 static NAT field, enter the VCS
Expressway's public IP address - this is the
IP address of the outside of the NAT.
The static NAT configuration options are
only available on VCS Expressway
systems which have the Dual Network
Interfaces option key installed.
Firewall
Applications
Maintenance
traversal
ADMINISTRATOR GUIDE
Appendices
Advertisement
Table of Contents
