Related Manuals for TANDBERG D1389801
Summary of Contents for TANDBERG D1389801
- Page 1 Content Server User Manual Software version S1 D1389801 This document is not to be reproduced in whole or in part without permission in writing from:...
- Page 2 The information in this document is furnished for informational purposes only, is subject to change without prior notice, and should not be construed as a commitment by TANDBERG. The information in this document is believed to be accurate and reliable; however TANDBERG...
- Page 3 INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT( INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE COPYRIGHT © 2006, TANDBERG...
- Page 4 Waste handling There is no need to send any products or material back to TANDBERG as there are no consumables to take care of. Please contact your local dealer for information on local waste handling and recycling of electronic products.
- Page 5 User Manual Operator Safety Summary For your protection, please read these safety instructions completely before operating the equipment and keep this manual for future reference. The information in this summary is intended for operators. Carefully observe all warnings, precautions and instructions both on the apparatus and in the operating instructions.
- Page 6 TANDBERG Content Server User Manual Servicing - Do not attempt to service the apparatus yourself as opening or removing covers may expose you to dangerous voltages or other hazards, and will void the warranty. Refer all servicing to qualified service personnel.
- Page 7 Contact us If you have any questions, comments or suggestions, please see the Online Support service at www.tandberg.net It is also possible to send a fax or mail to the attention of: Product and Sales Support TANDBERG P.O. Box 92...
- Page 8 TANDBERG Content Server User Manual End-User License Information IMPORTANT: THE USER MANUAL CD FOR THIS PRODUCT CONTAINS IMPORTANT TERMS AND CONDITIONS INCLUDING END USER LICENSE AGREEMENTS. THE LICENSE AGREEMENTS SHOULD BE READ PRIOR TO USE. USE OF THIS PRODUCT CONSTITUTES ACCEPTANCE OF THE TERMS OF THE LICENSES.
- Page 9 User Manual Table of Contents End-User License Information ....................... viii Introduction..........................1 Installation ..........................2 2.1 Unpacking ..........................3 2.2 Connecting cables ......................... 4 2.3 IP Address Setting Configuration................... 5 2.3.1 IP setting configuration: ..................... 5 2.3.2 Static IP configuration: ....................6 2.3.3 Content Server configuration ..................
- Page 10 Appendices..........................95 Appendix 1 – LED panel menu structure ................... 96 Appendix 2 – Compatibility ......................97 Appendix 3 – Troubleshooting guide ..................99 Appendix 4 - Example XML File....................101 Appendix 5 – TANDBERG Content Server port assignment........... 103...
- Page 11 1 Introduction The TANDBERG Content Server is the latest addition to the TANDBERG product range which provides users with a quick and easy way to record video meetings and view them live or on- demand from their computers. Features at a glance:...
- Page 12 TANDBERG Content Server User Manual 2 Installation Precautions: Never install communication wiring during a lightning storm. Never install jacks for communication cables in wet locations unless the jack is specifically designed for wet locations. Never touch uninstalled communication wires or terminals unless the communication line has been disconnected at the network interface.
- Page 13 The Content Server comes with rubber feet for standalone installation and brackets for mounting in standard 19” racks. Before starting the rack mounting please make sure the TANDBERG Content Server is placed securely on a hard flat surface. 1. Disconnect the AC power cable.
- Page 14 TANDBERG Content Server User Manual 4. Insert the Content Server into a 19” rack, and secure with screws in the front (four screws). 2.2 Connecting cables LAN cable Connect a LAN cable from the ‘LAN 1’ connector on the Content Server to your network. The LAN 2, 3 and 4’...
- Page 15 2.3 IP Address Setting Configuration The Content Server requires the IP Address Settings to be configured before it can be used. IP Address Configuration can be made using the LCD Panel. The default IP Address configuration is DHCP. It is recommended that administrators change the configuration to a Static IP address once the server is in production.
- Page 16 TANDBERG Content Server User Manual 5. Press Enter again at the Address Type screen and select the required configuration (DHCP or Static) by using the Up or Down arrows. 6. Press Enter to confirm. 7. If you have selected Static configuration, go to Section 2.3.2 Static IP configuration.
- Page 17 Password tool to change your administrative password. 2.3.4 User configuration The TANDBERG Content Server can be added to an existing domain to take advantage of Active Directory integration. If you add the Content Server to an existing domain, you need to define a separate security policy for the server, otherwise the existing security policies may prevent the server from functioning correctly.
- Page 18 TANDBERG Content Server User Manual 2.3.5 QuickTime installation NOTE: Read this section only if you require calls to be recorded and streamed in the ® QuickTime format. If you will be recording calls in two formats only - Windows Media and Real Media, you do NOT need to install QuickTime on the server.
- Page 19 Line 1 or Codec Support section for Archiving Lines 2-5). Remember to click the Save button to confirm the changes. 13. Attach Recording and Streaming Templates with QuickTime outputs to Lines 1-5 to take advantage of the QuickTime output functionality and record your content for on demand QuickTime playback.
- Page 20 TANDBERG Content Server User Manual 3 General Use TANDBERG Content Server The Content Server will always be turned on and be available to record conference calls. The unit itself should not be available to users at anytime. If the system does not respond: Check the LCD panel to determine if the unit is switched on and ‘live’.