Viessmann VITOTRONIC 200 Installation And Service Instructions Manual page 45

"Boiler" group
(cont.)
Coding in the delivered condition
06:74 Electronic maximum limit for boiler
water temperature set to 74 °C.
Note
The code has no effect during
DHW heating demand.
0b:0 Do not adjust
10:20 Hook-up delay for enabling stage 2
in addition to stage 1 during heat-
ing operation (integral) = 2560 Ks
11:20 Hook-up delay for enabling stage 2
in addition to stage 1 during cylin-
der heating (integral) = 2560 Ks
12:20 Shutdown delay for blocking stage
1 in addition to stage 2 (integral) =
2560 Ks
13:6 Shutdown differential 6 K
The burner shuts down when the
set boiler water temperature is ex-
ceeded.
15:15 Do not adjust
16:6 Modulating burner offset during
start optimisation 6 K
17:120 Modulating burner control amplifi-
cation 12 %/K
18:30 Modulating burner integral action
time 300 s
1A:6 Duration of the start optimisation
for modulating burner 6 min
1C:120 Signal B4 at plug
Compensation of signal delay for
hours run meter. Time from initia-
tion of burner start signal at T2 in
plug
fA
valve. At each burner start, 120 s
will be taken off the runtime.
1F:0 With flue gas temperature sensor:
Flue gas temperature is not moni-
tored for burner service indication
21:0 No service interval (hours run) se-
lected.
not available:
fA
to opening of the solenoid
Possible change
ERB80 function (values from 6 to
20 K)
06:20 Maximum limit adjustable from 20 to
to 127 °C.
06:127
Note
Observe the " " temperature con-
troller setting (see page 13)
10:0 Hook-up delay adjustable from 0 to
to 25,472 Ks.
10:199 1 step
11:0 Hook-up delay adjustable from 0 to
to 25,472 Ks.
11:199 1 step
12:0 Shutdown delay adjustable from 0 to
to 25,472 Ks.
12:199 1 step
13:0 Without shutdown differential
13:1 Shutdown differential adjustable
to from 1 to 20 K.
13:20
16:0 Offset adjustable from 0 to 15 K.
to
16:15
17:0 Setting subject to adaptation of mod-
to ulating burner to the boiler type from
17:255 0 to 25.5 %/K
1 step
18:1 Setting subject to adaptation of mod-
to ulating burner to the boiler type from
18:199 10 to 1990 s
1 step
1A:0 Duration adjustable from 0 to
to 60 min.
1A:60
1C:1 Delay adjustable from 1 to 199 s.
to This time is deducted from the oper-
1C:199 ating time at every burner start.
E.g. operating situations where the
burner is shut down via the mechan-
ical temperature controller, but a
burner demand is still present (hours
run continue to be counted).
If required, change the coding ad-
dress "06" in this group.
1F:1 When the limit for the flue gas tem-
to perature is exceeded, "Service" is
1F:250 °C displayed.
21:1 The number of hours run before the
to burner should be serviced, adjusta-
21:100 ble from 100 to 10,000 h.
Coding level 2
≙
128 Ks
≙
128 Ks
≙
128 Ks
≙
0.1 %/K
≙
10 s
45