Unidrive Vtc Parameter Range And Default Differences - Control Techniques Unidrive 1 Series User Manual

Safety Product Mechanical
Information Information Installation
10.21 Unidrive VTC parameter range and
default differences
The following parameters have a different range and/or default value
between Unidrive VTC and open-loop Unidrive. Any parameter not listed
below has the same range and default value as open-loop Unidrive.
Parameter
Menu 1
1.06 Maximum frequency
1.07 Minimum frequency
1.14 Reference selector
Menu 2
2.07 S-ramp da/dt
2.11 Acceleration rate 1 / Forward acceleration rate 1
2.12 Acceleration rate 2 / Forward acceleration rate 2
2.13 Acceleration rate 3 / Forward acceleration rate 3
2.14 Acceleration rate 4 / Forward acceleration rate 4
2.15 Acceleration rate 5 / Reverse acceleration rate 1
2.16 Acceleration rate 6 / Reverse acceleration rate 2
2.17 Acceleration rate 7 / Reverse acceleration rate 3
2.18 Acceleration rate 8 / Reverse acceleration rate 4
2.21 Deceleration rate 1 / Forward deceleration rate 1
2.22 Deceleration rate 2 / Forward deceleration rate 2
2.23 Deceleration rate 3 / Forward deceleration rate 3
2.24 Deceleration rate 4 / Forward deceleration rate 4
2.25 Deceleration rate 5 / Reverse deceleration rate 1
2.26 Deceleration rate 6 / Reverse deceleration rate 2
2.27 Deceleration rate 7 / Reverse deceleration rate 3
2.28 Deceleration rate 8 / Reverse deceleration rate 4
Menu 3
3.29 Over-speed threshold mode select
Menu 4
4.05 Motoring current limit
4.06 Regenerating current limit
4.07 Symmetrical current limit
Menu 5
5.06 Motor – rated frequency
5.14 Voltage mode selector
5.15 Boost voltage
5.16 Jog boost voltage
Menu 7
7.11 Analog input 2 mode selector
7.19 Analog output 1 source parameter
7.22 Analog output 2 source parameter
7.23 Analog output 2 output scaling
Menu 8
8.10 F1 destination or source parameter
8.16 F3 destination or source parameter
8.21 F5 destination parameter
8.23 F6 destination parameter
Menu 9
9.23 Motorised pot. rate
Unidrive User Guide
Issue Number: 9
Electrical Getting
Menu 0
Installation Started
{ 0.02 }
0 to [Pr 1.06 ], if Pr 1.08 = 0
{ 0.01 }
-250.0 Hz to 0, if Pr 1.08 = 1
{ 0.05 }
{ 0.19 }
{ 0.03 }
{ 0.04 }
{ 0.06 }
{ 0.47 }
{ 0.07 }
{ 0.08 }
VOLt (0), 0 - 20 (1), 20 - 0 (2),
4 - 20.Lo (5), 20 - 4.Lo (6),
4 - 20.Pr (7), 20 - 4.Pr (8)
www.controltechniques.com
Running
Optimisation Macros
the motor
Range
0 to 250.0 Hz
0 to 5
2
0 to 3,000.0 s /100 Hz
0 to 3,200.0 s/100Hz
0 to 3,200.0 s/100Hz
0 to 3,200.0 s/100Hz
0 to 3,200.0 s/100Hz
0 to 3,200.0 s/100Hz
0 to 3,200.0 s/100Hz
0 to 3,200.0 s/100Hz
0 to 3,200.0 s/100Hz
0 to 3,200.0 s/100Hz
0 to 3,200.0 s/100Hz
0 to 3,200.0 s/100Hz
0 to 3,200.0 s/100Hz
0 to 3,200.0 s/100Hz
0 to 3,200.0 s/100Hz
0 to 3,200.0 s/100Hz
0 to 3,200.0 s/100Hz
0
0 to I %
MAX
0 to I %
MAX
0 to I %
MAX
0 to 250.0 Hz
Fd (3)
0 to 15.0 %
0 to 15.0 %
4 - 20.tr (3), 20 - 4.tr (4),
EUR> VOLt (0), USA> 4 - 20.Lo (5)
Pr 0.00 to Pr 20.50
Pr 0.00 to Pr 20.50
0 to 4.000
Pr 0.00 to Pr 20.50
Pr 0.00 to Pr 20.50
Pr 0.00 to Pr 20.50
Pr 0.00 to Pr 20.50
0 to 250 s
Advanced Technical
Diagnostics
Parameters Data
Default
EUR> 50.0, USA> 60.0 RW
0 RW
0 RW
450.0 RW
60.0 RW
60.0 RW
60.0 RW
60.0 RW
60.0 RW
60.0 RW
60.0 RW
60.0 RW
60.0 RW
60.0 RW
60.0 RW
60.0 RW
60.0 RW
60.0 RW
60.0 RW
60.0 RW
0 RW
120.0 RW
120.0 RW
120.0 RW
EUR> 50.0, USA> 60.0 RW
Fd (3) RW
3.0 RW
3.0 RW
RW
Pr 2.01 RW
Pr 4.01 RW
EUR> 1.000, USA> 1.250 RW
EUR> Pr 10.06
RW
USA> Pr 10.02
Pr 1.45 RW
EUR> Pr 6.32
RW
USA> Pr 1.41
Pr 1.42 RW
30 RW
UL Listing
Information
Type
Uni
Uni
Uni
Uni
Uni
Uni
Uni
Uni
Uni
Uni
Uni
Uni
Uni
Uni
Uni
Uni
Uni
Uni
Uni
Uni
Bit
Uni
Uni
Uni
Uni
Uni
Uni
Uni
Txt R
Uni R P
Uni R P
Uni
Uni R P
Uni R P
Uni R P
Uni R P
Uni
181