Control Techniques Unidrive 1 Series User Manual page 144

Safety Product Mechanical
Information Information Installation
Parameter
6.01 Stop mode selector*
6.02 Auto-start mode selector
6.03 supply loss mode selector**
AC
6.04 Sequencing mode selector***
6.05 Minimum jog time
6.06 Injection braking level
6.07 Injection braking time*
6.08 Hold zero speed enable*
6.09 Synchronize to a spinning motor****
6.10 Synchronization ramp rate****
6.11 Keypad run key enable
6.12 Keypad stop key enable
6.13 Keypad fwd/rev key enable
6.15 Drive enable
6.16 Electricity cost / kWh
6.17 Power consumption meter reset
6.18 Time interval between filter changes
6.19 Filter change required/done
6.20 Time interval between lubrication
6.21 Lubrication required/done
6.22 Run-time log
6.23 Run-time log
6.24 Power meter
6.25 Power meter
6.26 Running cost
6.27 Time before filter change due
6.28 Time before lubrication due
6.29 Hardware enable
6.30 Sequencing bit 0
6.31 Sequencing bit 1
6.32 Sequencing bit 2
6.33 Sequencing bit 3
6.34 Run permit / not stop
6.35 Limit switch 1
6.36 Limit switch 2
6.37 Spinning motor start-voltage****
6.38 Spinning motor voltage-ramp****
RO Read Only parameter
RW Read / Write parameter
NOTE
Where a parameter is represented by a text value, the value in brackets
in the range column is the setting used for serial communications.
* For more information, refer to section 10.22.4 Stop Modes on
page 184.
** For more information, refer to section 10.22.5 Mains loss modes on
page 185.
*** For more information, refer to section 10.22.6 Sequencing Modes on
page 186.
**** For more information, refer to section 10.22.7 Catch a spinning
motor on page 187.
144
Electrical Getting
Menu 0
Installation Started
OL
COASt (0), rP (1),
{0.16} rP-dcI (2), dcI (3),
td.dcI (4)
diS (0), ALYS (1), Pd.dP (2)
diS (0), StoP (1), ridE.th (2)
0 to 100.0 %FLC
0 to 25.0 s
{0.39}
0 to 25.0 s/100Hz
0 to 600.0 Currency/kWh
0 to 30.365 years.days
0 to 32,000 Currency/hr
0 to 100.0 %
0 to 2.5 s
Uni Unipolar variable parameter
Bi Bipolar variable parameter
Txt Text variable parameter
Bit Bit parameter
www.controltechniques.com
Running
Optimisation Macros
the motor
Range( )
CL
COASt (0), rP (1),
no.rP (2), rP-POS (3)
0 to 4
0 to 25.0 s
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
0 to 30,000 hr
0 or 1
0 to 30,000 hr
0 or 1
0 to 23.59 hr min
0 to 30,000 MWh
0 to 999.9 kWh
0 to 30,000 hr
0 to 30,000 hr
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
R Reset required for new value to take effect
S New parameter-value saved at power-down
P Protected; forbidden as destination parameter
FLC Full-load current (max. continuous), Pr 11.32 {0.33}
Advanced Technical
Diagnostics
Parameters Data
Default( )
OL VT SV
rP (1) no.rP (2) RW Txt
diS (0) RW Txt
diS (0) RW Txt
4 RW Uni
0.0 RW Uni
100.0 RW Uni
5.0 RW Uni
0 1 RW Bit
0 1 RW Bit
5 RW Uni
0 RW Bit
0 RW Bit
0 RW Bit
1 RW Bit
0 RW Uni
0 RW Bit
0 RW Uni
1 RW Bit
0 RW Uni
1 RW Bit
0 RW Bit
0 RW Bit
0 RW Bit
0 RW Bit
0 RW Bit
25 RW Uni
0.25 RW Uni
Unidrive User Guide
Issue Number: 9
UL Listing
Information
Type
P
P
RO Uni S P
RO Uni S P
RO Uni S P
RO Uni S P
RO Uni S P
RO Uni S P
RO Uni S P
RO Bit P
RO Bit
RO Bit