Control Techniques Unidrive 1 Series User Manual page 146

Safety Product Mechanical
Information Information Installation
Parameter
7.01 Analog input 1
7.02 Analog input 2
7.03 Analog input 3
7.04 Heatsink temperature
7.05 Control board temperature
7.06 Analog input 1 mode selector
7.07 Analog input 1 offset trim
7.08 Analog input 1 scaling
7.09 Analog input 1 invert
7.10 Analog input 1 destination parameter
7.11 Analog input 2 mode selector
7.12 Analog input 2 scaling
7.13 Analog input 2 invert
7.14 Analog input 2 destination parameter
7.15 Analog input 3 mode selector
7.16 Analog input 3 scaling
7.17 Analog input 3 invert
7.18 Analog input 3 destination parameter
7.19 Analog output 1 source parameter
7.20 Analog output 1 scaling
7.21 Analog output 1 mode selector
7.22 Analog output 2 source parameter
7.23 Analog output 2 scaling
7.24 Analog output 2 mode selector
7.25 Calibrate analog input 1 full scale
7.26 V/f sample time
Analog input 1 current-loop loss
7.27
indicator
Analog input 2 current-loop loss
7.28
indicator
Analog input 3 current-loop loss
7.29
indicator
7.30 Analog output set-up enable
UD78 large option module fitted
7.31
indicator
7.32 IGBT junction temperature
RO Read Only parameter
RW Read / Write parameter
NOTE
Where a parameter is represented by a text value, the value in brackets
in the range column is the setting used for serial communications.
146
Electrical Getting
Menu 0
Installation Started
OL
VOLt (0), 0 - 20 (1), 20 - 0 (2), 4 - 20.tr (3),
{0.24} 20 - 4.tr (4), 4 - 20.Lo (5), 20 - 4.Lo (6),
4 - 20.Pr (7), 20 - 4.Pr (8)
Pr 0.00 to Pr 20.50
{0.25}
{0.26} Pr 0.00 to Pr 20.50
VOLt (0), 0 - 20 (1), 20 - 0 (2), 4 - 20.tr (3) ,
20 - 4.tr (4), 4 - 20.Lo (5) , 20 - 4.Lo (6),
4 - 20.Pr (7), 20 - 4.Pr (8), th.SC (9), th (10)
Pr 0.00 to Pr 20.50
Pr 0.00 to Pr 20.50
VOLt (0), 0 - 20 (1), 4 - 20 (2)
Pr 0.00 to Pr 20.50
VOLt (0), 0 - 20 (1), 4 - 20 (2)
Uni Unipolar variable parameter
Bi Bipolar variable parameter
Txt Text variable parameter
Bit Bit parameter
www.controltechniques.com
Running
Optimisation Macros
the motor
Range( )
CL
±100.0 %
±100.0 %
±100.0 %
o
0 to 100 C
o
0 to 100 C
±10.000 %
0 to 4.000
0 or 1
(as Pr 7.06)
0 to 4.000
0 or 1
0 to 4.000
0 or 1
0 to 4.000
0 to 4.000
0 or 1
0 to 5.0 ms
0 or 1
0 or 1
0 or 1
0 or 1
0 or 1
0 to 150 °C
R Reset required for new value to take effect
S New parameter-value saved at power-down
P Protected; forbidden as destination parameter
FLC Full-load current (max. continuous), Pr 11.32 {0.33}
Advanced Technical
Diagnostics
Parameters Data
Default( )
OL VT SV
VOLt (0)
0
1.000
0
Pr 1.36
VOLt (0)
1
0
Pr 1.37
EUR> th (10), USA> VOLt (0)
1.000
0
Pr 0.00
Pr 5.01 Pr 3.02
1
VOLt (0)
Pr 4.02
1.000
VOLt (0)
0
4.0
0
Unidrive User Guide
Issue Number: 9
UL Listing
Information
Type
RO Bi P
RO Bi P
RO Bi P
RO Uni P
RO Uni P
RW Txt R
RW Bi P
RW Uni
RW Bit
RW Uni R P
RW Txt R
RW Uni
RW Bit
RW Uni R P
RW Txt R
RW Uni
RW Bit
RW Uni R P
RW Uni R P
RW Uni
RW Txt R P
RW Uni R P
RW Uni
RW Txt R P
RW Bit
RW Uni
RO Bit P
RO Bit P
RO Bit P
RW Bit
RO Bit P
RO Uni P