Gatekeeper Systems Digital Smart Recorder NiTRO 900 Manual page 28

CAMERA DWELL
PURPOSE: Camera Dwell is used to set the system up to automatically switch cameras when there is more than one PURPOSE PURPOSE PURPOSE
connected to the system. The options are to switch on S S S S ensors
Sensors: Selected camera will switch when sensor becomes active Sensors: Sensors: Sensors:
Example: If camera 1 is set to main camera and camera 2 is set as the stop arm camera, the system will always record on
camera 1 until the stop arm sensor becomes active. As long as that sensor is active, it will record on camera 2 instead of
camera 1. When the stop arm sensor becomes inactive, the system will return to recording on camera 1.
Dwell Time: All cameras will switch in order according to a specified time interval (dwell time). Time interval options are Dwell Time Dwell Time Dwell Time
from 5 5 5 5 - - - - 70 70 seconds in 5 second increments.
70 70
ENTRY: Use the plus and minus keys to scroll ENTRY ENTRY ENTRY
through all the options.
RECORD QUALITY
PURPOSE PURPOSE PURPOSE PURPOSE: The Record Quality menu gives two options used for recording:
Standard: Standard: 320 x 240 resolution at full 1 - 30 FPS
Standard: Standard:
High Res: High Res: 640 x 480 resolution at only 5 FPS
High Res: High Res:
ENTRY: Use the plus and minus keys to toggle ENTRY ENTRY ENTRY
between the two options.
RECORD FPS
PURPOSE: The Frames per second options relate to the video standard used. PURPOSE
PURPOSE PURPOSE
For NTSC mode, the FPS is listed as 1, 1, 1, 1, 5, 5, 5, 5, 10,
For PAL mode, the FPS is listed as 1, 5, 10, 15, 20, 25
ENTRY: Use the plus and minus keys to toggle ENTRY ENTRY ENTRY
between the two options.
Note: The FPS cannot be changed if the Record
Quality is set to High Res
Lowering the FPS will increase the
record time
SENSOR SETUP
PURPOSE PURPOSE PURPOSE PURPOSE: There are eight pins on the serial port that are used as sensors. Each sensor is displayed on the main recording
screen when it becomes active. The character that gets displayed is the first character in the label. Example: IGN is active so
"I" is displayed. If the label was changed to "DOOR", the letter "D" would be displayed.
ENTRY: Press 'Go' to enter the Sensor Setup menu. ENTRY
ENTRY ENTRY
Use the plus and minus sign keys to increment
each character. Use the left or right arrow keys to
jump to the next character and/or field.
Label: : : : The default names are 3EX, ALM, IGN, Label
Label Label
ensors ensors only, or on a D D D D well ensors
EXIT: Use the right arrow to advance to the next menu or left arrow to EXIT EXIT EXIT
advance to the previous menu. Press the blue menu button to exit and
return to the Advanced sub menu.
EXIT: Use the right arrow to advance to the next menu or left arrow to EXIT EXIT EXIT
advance to the previous menu. Press the blue menu button to exit and
return to the Advanced sub menu.
10, 10, 1 1 1 1 5, 5, 5, 5, 20, 10, 20, 25, 30 20, 20, 25, 30 25, 30 25, 30
1, 5, 10, 15, 20, 25 1, 5, 10, 15, 20, 25 1, 5, 10, 15, 20, 25
EXIT: Use the right arrow to advance to the next menu or left arrow to EXIT
EXIT EXIT
advance to previous menu. Press the blue menu button to exit and
return to the Advanced sub menu.
EXIT: Press the blue menu button to exit the Sensor Setup menu and EXIT
EXIT EXIT
return to the Advanced sub menu.
DEFAULT CONDITION: Sensors with default labels, triggered on active DEFAULT CONDITION
DEFAULT CONDITION DEFAULT CONDITION
-28-
well T T T T ime well well ime interval. ime ime
DEFAULT CONDITION DEFAULT CONDITION DEFAULT CONDITION DEFAULT CONDITION: Sensors
DEFAULT CONDITION: Standard DEFAULT CONDITION
DEFAULT CONDITION DEFAULT CONDITION
DEFAULT CONDITION: 30 DEFAULT CONDITION DEFAULT CONDITION DEFAULT CONDITION