Carrier VVT Zone Installation And Startup Manual page 76

Index
Baseboard Heating Capacity • 51
Calculated DCV Damper Position • 63
Calculated Dehumidify Dmpr Position • 63
Calibrated Damper Close • 60
Calibrated Damper Open • 60
Cancel override • 67
CO2 (ppm) • 51
CO2 Sensor • 67
CO2 Sensor Max Input Volts • 60
CO2 Sensor Min Input Volts • 60
CO2 Sensor Value @ Max Volts • 60
CO2 Sensor Value @ Min Volts • 60
Cool Max • 60
Cool Min • 60
Cool Start K factor • 53
Cooling Capacity • 30, 53
Cooling Design Temp • 30, 53
Cooling Max Damper Position • 33, 60
Cooling Min Damper Position • 33, 43, 60
Damper Area (sq.In.) • 33, 60
Damper Full Close • 60
Damper Motor Travel Time • 60
Damper Position • 51
Damper Size (in.) • 34, 60
DCV Control • 60
DCV Max Ctrl Setpoint • 30, 43, 52, 53
DCV Max Damper Pos • 52
DCV Max Vent Damper Pos • 30, 43, 52
DCV Start Ctrl Setpoint • 30, 43, 52, 53
Direction Clockwise • 33, 60
Dirty Filter Alarm • 58
Ducted Heat • 33, 60
Ducted Heat Capacity • 51
Each Pulse • 67
Effective Heat Setpoint • 63
Effective setpoints • 53
Electric auxiliary heat • 42
External Actuator Enable • 33, 60
Fan • 51, 60
Fan Off Delay • 42, 52
Fan S/S • 67
Fan S/S or EH 3 • 67
Filter • 65
Filter Alarm • 45, 65
Filter Runtime • 45
Filter Service Alarm Timer • 45, 52
Global Occupancy • 63
Heat Delay • 63
Heat Enable • 30, 52
Heat Max • 60
Heat Min • 60
Heat Start K factor • 53
Heat Type • 34, 42, 60
Heating Capacity • 30, 51, 53
Heating Design Temp • 30, 53
Heating Lockout Temperature • 30, 42, 52
Heating Max Damper Position • 33, 60
Heating Min Damper Position • 33, 43, 60
Heating Stage 1 • 67
Heating Stage 2 • 67
High SAT Alarm Limit • 45, 58
Hot Water Valve • 67
Hysteresis • 30, 53
72
IAQ / Ventilation alarm • 58
IAQ Sensor • 60
IAQ Source • 63
Indoor Air Quality • 65
Indoor Air Quality Alarm • 45, 65
Inhibit Cooling Call from this zone • 65
Inhibit Heating Call from this zone • 65
LAT Airflow Increase • 51
Learned cooling capacity • 53
Learned heating capacity • 53
Learning Adaptive Optimal Start • 53
Learning Adaptive Start • 53, 63
Linkage Callers • 36, 46, 65
Linkage Collector • 34, 65
Linkage IAQ Type • 65
Linkage Provider • 34, 65
Linkage RH Type • 65
Linkage Zone Type • 34, 65
Local Sensor Calibration • 52
Locked Value • 63
Low SAT Alarm Limit • 45, 58
Max Accum • 67
Max Adjust • 67
Max Present Value • 67
Maximum Heating SAT • 52
Min Present Value • 67
Min Setpoint Separation • 53, 60
Modulating hot water/steam heating heat • 42
Network • 63
Network OAT Sensor Alarm • 65
Network Visible • 67
Number of Heat Stages • 33, 60
Object Name • 67
Occ Contact Status • 63
Occ High RH Alarm Limit • 45, 58
Occ Override Normal Logic State • 44, 60
Occupancy • 63
Occupancy Contact State • 63, 67
Occupancy Contact Status • 63
Occupancy Schedules • 44, 52
Occupancy Status • 63
Occupied Alarm Hysteresis • 45, 58
Occupied Cooling • 53
Occupied Cooling 1 • 53
Occupied Cooling 2 • 53
Occupied Heating • 53
Occupied Heating 1 • 53
Occupied Heating 2 • 53
Occupied High CO2 Alarm Limit • 45, 58
Occupied RH Control Setpoint • 30, 43, 53
Occupied Setpoints • 53
Optimal Start • 30, 44, 46, 53
Optimal Start Type • 53
Optional Ctrl Type • 33, 60
Optional Sensor Type • 60
Outdoor Air Temperature • 51
Outdoor Air Temperature Source • 63
Outdoor Air Temperature Status • 63
Override Time Remaining • 63
Parallel Fan Heat On Delay • 30, 42, 52
Parallel Fan On Value • 30, 41, 53
PD (Perssure Dependent) Control • 33, 60
Power Fail Restart Delay • 52
VVT Zone Controller