Table of Contents
Advertisement
Index
Numbers
262–8MA12. See Closed–loop control module
IP 262
262–8MB12. See Closed–loop control module
IP 262
263–8MA11. See IP 263 Positioning module
264–8MA11. See Electronic cam controller mo-
dule IP 264
265–8MA01. See IP 265 high speed sub control
266–8MA11. See IP 266 positioning module
267–8MA11. See IP 267 Stepper motor control
module
315–8MA11. See Interface module IM 315
316–8MA12. See Interface modules IM 316
330–8MA11. See Diagnostic module
380–4AB01. See Stromversorgungsbaugruppe
PS 2410
380–8MA11. See Timer module 2x0.3 to 300s
385–8MA11. See Counter module 2 x 0 to 500
Hz
385–8MB11. See Counter module 25/500 kHz
461–8MA11. See Comparator module
464–8MA11, analog input module, 7-14
464–8MA21, analog input module, 7-12, 7-14
464–8MB11, analog input module, 7-5
464–8MC11, analog input module, 7-5
464–8MD11, analog input module, 7-6
464–8MF21, analog input module, 7-15
466–8MC11, analog input module, 7-5, 7-23
521–8MA21. See CP 521 SI communications
processor
521–8MB11. See CP 521 BASIC communica-
tions module
700–8MA11. See Bus unit (SIGUT)
700–8MA21. See Bus unit (Crimp–snap–in)
788–8MA11. See Simulator module
931–8MD11. See Power supply module PS 931
935–8ME11. See Power supply module PS 935
A
Abort, 6-11
Access mode, B-1
ACI, 6-34
Acknowledge–Event–Notification, 6-12
Active node, B-1
Address, 1st available, 4-6, 4-7, 5-6, 5-7
ET 200 Distributed I/O Station
EWA 4NEB 812 6087–02b
Address assignment using COM ET 200
ET 200U (DP Siemens), 4-3–4-16
ET 200U (DP Standard), 5-3–5-19
Address identifier, B-1
Address IDs
ET 200U(DP Siemens), 4-9–4-13
ET 200U(DP Standard), 5-9–5-13
Address space, 1-3
Addressing, 9-42
with multi–tier configuration, 3-11
Addressing range, ET 200U, 3-1
Addressing with CPUs 941, 942, 943 and 944
ET 200U(DP Siemens), 4-7–4-8
ET 200U(DP Standard), 5-7–5-8
Alter–Event–Condition–Monitoring, 6-12
Analog input module
464–8MA11, 7-14
464–8MA21, 7-12, 7-14
464–8MB11, 7-5
464–8MC11, 7-5
464–8MD11, 7-6
464–8MF21, 7-15
466–8MC11, 7-5, 7-23
start–up, 7-11
Analog input modules, 7-2, 8-41
2 x PT 100 / +/–500 mV, 8-55
2 x PT 100 / +/–500 V, 8-53
4 x +/– 20 mA, 8-51
4 x +0 ... 10 V, 8-57
4x+/– 1 V, 8-45
4x+/– 20 mA, 8-49
4x+/– 50 mV, 8-41, 8-43
4x+/–10 V, 8-47
Analog output modules, 7-25, 8-59
2 x +/–10 V, 8-59
2 x +/–20 mA, 8-61
2 x 1 to 5 V, 8-65
2 x 4 to 20 V, 8-63
Analog value representation, 7-16
Arc suppression element, B-1
Area
ET 200U(DP Siemens), 4-6
ET 200U(DP Standard), 5-6
Array, B-1
ATTR, 6-33
Index
Index-1
Advertisement
Table of Contents
