1. Manuals
  2. Brands
  3. TE Connectivity Manuals
  4. Industrial Equipment
  5. Basic AMP-O-LECTRIC K 1-471273-3
  6. Customer's manual

TE Connectivity Basic AMP-O-LECTRIC K 1-471273-3 Customer's Manual

Terminating machine, main accessories and most common modifications
Hide thumbs
Table of Contents

Advertisement

Quick Links

© 2012 Tyco Electronics Corporation, a TE Connectivity Ltd. Company
All Rights Reserved
*Trademark
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.
Basic AMP-O-LECTRIC* Model "K"
Terminating Machine 471273-[ ], Main
Accessories and Most Common Modifications
SAFETY PRECAUTIONS
1. INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. DESCRIPTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1. Physical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.2. Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.3. Vertical Reel Bracket Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
2.4. Electrical System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3. RECEIVING INSPECTION AND INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.1. Receiving Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.2. Factors Affecting Machine Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
3.3. Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4. OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.1. Hand Cycling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.2. Production Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5. PREVENTIVE MAINTENANCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.1. Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.2. Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.3. Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6. TROUBLESHOOTING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
7. ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7.1. Crimp-Height/Shut-Height (Base Mount) Adjustment. . . . . . . . . . . . . . . . . . . . . . . . . 17
7.2. Feed Connecting Rod Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
7.3. Feed Mechanism Damper Screw and Rear Stop Screw Adjustment. . . . . . . . . . . . . 18
7.4. Guard Installation and Repair. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
8. REPLACEMENT AND REPAIR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
8.1. Trip Control Box Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
8.2. Foot Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
10. MACHINE ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
11. MODIFIED MACHINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
12. ROHS INFORMATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
13. REVISION SUMMARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
1-800-722-1111
READ THIS FIRST !
. . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
This controlled document is subject to change.
For latest revision and Regional Customer Service,
visit our website at www.te.com
Customer Manual
409-5128
17 JAN 12 Rev Z
1 of 61
LOC B

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Basic AMP-O-LECTRIC K 1-471273-3 and is the answer not in the manual?

Questions and answers

Related Manuals for TE Connectivity Basic AMP-O-LECTRIC K 1-471273-3

Summary of Contents for TE Connectivity Basic AMP-O-LECTRIC K 1-471273-3

  • Page 1 All Rights Reserved 1-800-722-1111 For latest revision and Regional Customer Service, *Trademark visit our website at www.te.com LOC B TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.
  • Page 2 409-5128 DANGER STOP SAFETY PRECAUTIONS AVOID INJURY Safeguards are designed into this application equipment to protect operators and maintenance personnel from most hazards during equipment operation. However, certain safety precautions must be taken by the operator and repair personnel to avoid personal injury, as well as damage to the equipment. For best results, application equipment must be operated in a dry, dust-free environment.

  • Page 3: Introduction

    409-5128 Figure 1 1. INTRODUCTION This manual covers basic AMP-O-LECTRIC Model "K" Terminating Machine 1-471273-3 and 1-471273-4 (shown in Figure 1), main accessories, and most common modifications. MACHINE NUMBER MACHINE DESCRIPTION 1-471273-3 115 Vac, 60 Hz, and comes with Mechanical Feed Option 692140-2 factory installed 1-471273-4 230 Vac, 50 Hz, and does NOT include Mechanical Feed Option 692140-2 The machine is used to power the applicator that applies strip-fed terminals to wire.

  • Page 4: Description

    409-5128 Packaged with every applicator is a parts list identifying the required machine number for that applicator. The parts list also identifies the accessories necessary to convert the machine to the required configuration. The basic machine is fitted to accept standard applicators, which are semi-permanently mounted to the machine for production of one size and type of terminal without the need for frequent changeover of applicators or changes in the applicator crimp height.

  • Page 5: Functional Description

    409-5128 vertical reel bracket assembly. The electrical system consists of a main power switch, work lamp, and panel light located on the left front of the machine; a trip control box assembly inside the back cover; a foot switch; and electrical wiring.

  • Page 6: Vertical Reel Bracket Assembly

    409-5128 The toggle lever subassembly is secured in the frame by the toggle arm pin at the front (see Figure 4). This pin acts as the pivot point. Another pin connects the link to the lever, and the opposite end of the link is connected to the ram by a pin.

  • Page 7: Electrical System

    409-5128 2.4. Electrical System (Figure 5 and Figure 6 ) The electrical system of the basic machine consists of a motor, trip control box, transmission solenoid, foot switch, barrier strip, main power (control) switch, work lamp, panel light, and wiring. The basic electrical system may be modified when adapted for special applications.
  • Page 8 409-5128 Figure 5 Rev Z 8 of 61...
  • Page 9 409-5128 Figure 6 Rev Z 9 of 61...

  • Page 10: Installation

    409-5128 D. Foot Switch When the operator is correctly positioned in front of the machine, the foot should rest on the switch comfortably and easily. The switch should be placed on a rubber mat: this allows it to be movable and permits the operator to shift positions to reduce fatigue, while at the same time the mat prevents the switch from sliding unintentionally.

  • Page 11: Operation

    409-5128 When machines are shipped with an applicator installed, an attached package will contain an envelope with crimped NOTE product samples which will be to the customer's specifications. These samples should be used as a comparison. All significant test results are recorded on the applicator parts list, included in the envelope, and were made under power. Examination of the complete machine for evidence of loose screws, bolts, and other components is recommended, after which it should be securely bolted to the bench to prevent movement during operation.

  • Page 12: Production Operation

    409-5128 4. As the machine ram nears the bottom of the stroke, closely observe tooling for proper alignment. If misalignment is evident, STOP rotation of flywheel and determine cause. If adjustment to machine is required, see Section 7. If adjustments to the applicator are required, refer to the appropriate instruction sheet. If machine is for a special application, see the appropriate customer manual.

  • Page 13: Preventive Maintenance

    409-5128 5. PREVENTIVE MAINTENANCE Preventive maintenance is cleaning, inspecting, and lubricating the machine to keep it in continuous operation. It is suggested that a regular maintenance program be established and followed to eliminate the cost of unnecessary repairs. For applicators and special applications of the machine, refer to the publications supplied with them.
  • Page 14 409-5128 Figure 10 (Cont’d) Rev Z 14 of 61...
  • Page 15 409-5128 Figure 10 (End) Rev Z 15 of 61...

  • Page 16: Troubleshooting

    409-5128 6. TROUBLESHOOTING Figure 11 is presented in order of normal sequence. The second column lists the probable causes in the order most likely to occur and be checked. The third column lists the remedy for each of the probable causes and references to other parts of the manual that should be helpful in remedying the problem.

  • Page 17: Adjustments

    409-5128 7. ADJUSTMENTS The following adjustments are required to maintain the machine in continuous operation and to set it up after replacement of parts. To avoid personal injury, ALWAYS disconnect the electrical and air supply, before performing any adjustment, unless DANGER otherwise specified.

  • Page 18: Feed Connecting Rod Adjustment

    409-5128 When specified to loosen the two base mount retaining cap screws in the following procedure, ALWAYS remove any CAUTION clearance between the adjustment block and the base mount by turning the adjusting screw COUNTERCLOCKWISE, as viewed from left side of the machine. If the crimp height of the terminal is KNOWN to be GREATER than the specified crimp height, omit Steps 1 and 2;...
  • Page 19 409-5128 Feed Actuating Mechanism Toggle Lever Subassembly (Ref) Spherical Bearing Link Feed Connecting Rod  Vertical Reel Bracket and Spring Assembly Feed Actuating Block Feed Actuating Arm Adjusting Locknuts Feed Arm Drive Shaft Damper Screw and Block Figure 13 7.4. Guard Installation and Replacement (Figure 14) The "K"...
  • Page 20 409-5128 Side-Feed Shroud Wire Access Slot End-Feed Shroud Side-Feed Guard End-Feed Guard COMMON END-FEED APPLICATOR GUARDS INSERT PART NUMBER OPENING SIZE (mm [In.]) DESCRIPTION 455745-1 6.35 [.250] Standard guard - insulation diameters up to Ø6.35 [.250] 457352-1 9.53 [.375] Insulation diameters from Ø6.35 [.250] to Ø9.53 [.375]Ø 457353-1 6.35 [.250] For terminals taller than 6.35 [.250]...

  • Page 21: Replacement And Repair

    409-5128 8. REPLACEMENT AND REPAIR To avoid personal injury, ALWAYS disconnect electrical and air supply before attempting any repairs or replacement of DANGER parts. STOP The procedures in this section cover those items not shown disassembled in Section 9 but which require detailed instructions for repair or replacement of internal parts.
  • Page 22 409-5128 ITEM PART NUMBER DESCRIPTION - - - 1-471273-3 MACHINE ASSEMBLY, Basic Machine (115V 60Hz) - - - - - - 1-471273-4 MACHINE ASSEMBLY, Basic Machine (230V 50Hz) - - - 3-21001-3 SCREW, Skt Hd Cap, 3/8-16 X .750 in. L 694925-1 BRACKET ASSEMBLY, Vertical Reel (See Figure 18 for Components) 26148-6...
  • Page 23 409-5128 See Figure 18 for Components Breakdown Continued on Figure 16 Breakdown Continued on Figure 20 Figure 15 (End) Rev Z 23 of 61...
  • Page 24 409-5128 ITEM PART NUMBER DESCRIPTION - - - 1-471273-3 MACHINE ASSEMBLY, Basic Machine (115V 60Hz) - - - - - - 1-471273-4 MACHINE ASSEMBLY, Basic Machine (230V 50Hz) - - - 3-21001-7 SCREW, Skt Hd Cap, 3/8-16 X 1.500 in. L 371178 WASHER, Special 223141-3...
  • Page 25 409-5128 See Figure 21 for Components Figure 16 (End) Rev Z 25 of 61...
  • Page 26 409-5128 ITEM PART NUMBER DESCRIPTION - - - 1-471273-3 MACHINE ASSEMBLY, Basic Model “K" Machine (115V 60Hz) - - - - - - 1-471273-4 MACHINE ASSEMBLY, Basic Model “K" Machine (230V 50Hz) - - - 20870-2 SWITCH, Toggle 24195-1 PLATE, Switch 23403-1 NUT, Speed 23709-1...
  • Page 27 409-5128 ITEM PART NUMBER DESCRIPTION 1-21002-6 SCREW, Btn Hd Cap, 6-32 X .250 in. L 1-21899-3 WASHER, Flat, No. 8 373306-2 PLATE, Switch Adapter 5-21063-5 SCREW, Brass Rnd Hd, 10-32 X .375 in. L 21075-5 WASHER, Int Tooth Lock, No. 10 551172-1 •...
  • Page 28 409-5128 Figure 17 (Cont’d) Rev Z 28 of 61...
  • Page 29 409-5128 Figure 17 (End) Rev Z 29 of 61...
  • Page 30 409-5128 ITEM PART NUMBER DESCRIPTION - - - 694925-1 • BRACKET ASSEMBLY Vertical Reel (Right-Hand Feed) - - - 2-22789-6 SCREW, Thumb Wing, 1/4-20 X .500 in. L 465520-1 FLANGE, Reel 3-21001-3 SCREW, Skt Hd Cap, 3/8-16. X 750 in. L 21024-8 WASHER, Spring Lock, 3/8 in.
  • Page 31 409-5128 ITEM PART NUMBER DESCRIPTION - - - - - - MOTOR-FLYWHEEL COMPONENTS - - - 23139-1 • V-BELT - - - 5570646-1 FLYWHEEL ASSEMBLY 23143-1 PIN, Dowel, .125 Dia X .500 in. L 375021 PLATE, Drive 469766-1 BUSHING, Flywheel, Replacement - - - FLYWHEEL (Not Available Separately;...
  • Page 32 409-5128 ITEM PART NUMBER DESCRIPTION - - - - - - TRANSMISSION COMPONENTS, Basic Machine - - - 22140-3 SCREW, Skt Hd Cap, 1/4-20 X .625 in. L 21899-3 WASHER, Flat, 1/4 in. 21021-4 NUT, Slflkg Hex, 10-32 3-21000-7 SCREW, Skt Hd Cap, 10-32.75 in. L 21899-2 WASHER, Flat, No.
  • Page 33 409-5128 ITEM PART NUMBER DESCRIPTION 21009-2 SETSCREW, Slflkg Skt, 1/4-20 X .250 in. L 21014-5 SCREW, Lkg Type, 1/4-20 X .125 in. L 21009-3 SETSCREW, Slflkg Skt, 1/4-20 X .312 in. L 811925-1 COLLAR, Stop 811938-1 DOG, Clutch 372687 SPRING, Compression 551353-1 KEY, Square 21029-9...
  • Page 34 409-5128 Figure 20 (End) Rev Z 34 of 61...
  • Page 35 409-5128 ITEM PART NUMBER DESCRIPTION - - - - - - TOGGLE LEVER-FEED ACTUATING COMPONENTS - - - 23138-3 PIN, Cowling 21899-7 WASHER, Flat, 1/2 in. 1-21021-7 NUT, Slflkg Hex, 3/8-24 22595-6 NUT, Hex Lk, 3/8-24 373479 COLLAR, Feed Rod 375092 BLOCK, Feed Actuating 373475...
  • Page 36 409-5128 Figure 21 (End) Rev Z 36 of 61...

  • Page 37: Machine Accessories

    409-5128 10. MACHINE ACCESSORIES This section pertains to those accessories that when factory installed change the basic machine to one of the modified machines presented in Section 11. These same accessories are available for field conversions, making it possible to change a modified machine of one configuration to that of another. The assembly (or assemblies) required, and the parts that will need to be removed, depend on the intended application and the type of applicator to be installed.
  • Page 38 409-5128 Figure 22 It should be noted that the machine is not at BOTTOM-DEAD-CENTER nor is ram at bottom of stroke. This is normal and NOTE will be compensated for by the feed return spring. 9. Adjust damper screw until it JUST TOUCHES the feed actuating arm, then tighten locknut to secure it. This adjustment must be correct;...
  • Page 39 409-5128 Vertical Reel Bracket Assembly (Ref) Feed Actuating Arm Feed Finger (Ref, Supplied )with the Standard Applicator ITEM PART NUMBER DESCRIPTION - - - 692140-2 • ARM ASSEMBLY, Mechanical Feed 23138-1 PIN, Cowling 374112 SPRING, Feed Tension 374651 PIN, Feed Clevis 1-21021-7 NUT, Slflkg Hex, 3/8-24 374114...
  • Page 40 409-5128 10.2. Air Feed Valve Assembly (Figure 24) A. Description The air feed valve assembly is used to supply air pressure to all types of applicator air feed arrangements. The assembly consists of a valve bracket, on-off valve, operating arm, flow control valve, quick-exhaust valve, and tubing with fittings.
  • Page 41 409-5128 ITEM PART NUMBER DESCRIPTION - - - 692655-1 • VALVE ASSEMBLY, Air Feed - - - 22306-2 ELBOW, Street, 1/4 x 1/4 in. NPT 22312-4 ADAPTER, Hex, 1/8 X 1/4 in. NPT 27319-4 TUBING, Plastic, 1/4 in. Outside Diameter, 381 mm [15 in.] 980285-2 ELBOW, Male, 1/8 in.
  • Page 42 409-5128 Inlet Body Exhaust Body Gasket Cap Screw Diaphragm Note: Schrader valve shown, Deltrol valve is similar. Figure 25 10.3. Air Feed Assemblies A. Description (Figure 26) There are three different types of air feed assemblies available, each with a specific purpose, but similar in design and operation.
  • Page 43 409-5128 Vertical Reel Bracket Assembly (Ref) Air Supply Inlet Flow Control Valve ON-OFF  Valve Operating Arm Flow Adjustment  Lockscrew Screw Valve  Bracket Feed Bracket (Ref) Guide Rod Swivel Screw Feed Adjusting Bracket Typical Air Feed Cylinder Adjusting Block Feed Piston ...
  • Page 44 409-5128 7. Check that feed finger is against feed point in terminal strip for lead terminal. If not, loosen lockscrew securing feed adjusting block, and turn feed adjusting screw, as required, until feed finger is against feed point and lead terminal remains centered over anvil. Tighten lockscrew to secure adjustment. 8.
  • Page 45 409-5128 ITEM PART NUMBER DESCRIPTION - - - 690021 • FEED ASSEMBLY, Air, 2-in. Stroke - - - 690021-1 • FEED ASSEMBLY, Air, 1-in. Stroke 692655-1 VALVE ASSEMBLY, Air Feed (See Figure 24) 3-21001-6 SCREW, Skt Hd Cap, 3/8-16 X 1.250 in. L 21024-8 WASHER, Lock, 3/8 in - - -...
  • Page 46 409-5128 Base Mount (Ref) Feed Arm Drive Shaft  and Bracket (Ref) Typical Feed Finger (Ref) Figure 27 (End) Rev Z 46 of 61...
  • Page 47 409-5128 ITEM PART NUMBER DESCRIPTION - - - 460277-1 • FEED ASSEMBLY, Air, 1-in. Stroke, Single End-Feed - - - - - - 460277-2 • FEED ASSEMBLY, Air, 2- in. Stroke, Single End-Feed - - - - - - 460277-3 • FEED ASSEMBLY, Air, 1-in.
  • Page 48 409-5128 Air Feed Valve Assembly (Ref) Feed Arm Drive Shaft  and Bracket (Ref) Figure 28 (End) Rev Z 48 of 61...
  • Page 49 409-5128 ITEM PART NUMBER DESCRIPTION - - - 457098-1 • FEED ASSEMBLY, Air (Used on Tab-Lok Miniature Applicators) - - - 692655-8 • VALVE ASSEMBLY, Air Feed 3-21001-5 SCREW, Skt Hd Cap, 3/8-16 X 1.000 in. L 21024-8 WASHER, Flat, 3/8 in. 456919-1 PLATE, Air Feed Mounting 21045-3...
  • Page 50 409-5128 Attaches to Back  of Applicator Feed Arm Drive Shaft and Bracket (Ref) Figure 29 (End) Rev Z 50 of 61...
  • Page 51 409-5128 Plug Spring Spring  Cylinder  “O" Ring Shell Piston End Piston Gasket Washer Tie Rod Screw Figure 30 10.4. Air Blast Assemblies (Figure 31) A. Description Three air blast assemblies (455350-1 through -3) are available as accessories for use with standard applicators.
  • Page 52 409-5128 C. Replacement There are no special procedures required for the replacement of parts in the air blast assemblies. Refer to the exploded view and parts list for detail parts. ITEM PART NUMBER DESCRIPTION - - - 455350-1 • BLAST ASSEMBLY, Air (For Applicator with Air Feed) - - - - - - 455350-2 •...
  • Page 53 409-5128 Assembly 455350-1 Air Supply (IN) Air Blast (OUT) Feed Arm Drive Shaft and Bracket (Ref) Air Feed Valve (Ref) Assemblies 455350-2 and -3 Air Blast (OUT) Air Supply (IN) Feed Arm Drive Shaft and Bracket (Ref) Rev Z 53 of 61...
  • Page 54 409-5128 10.5. Optional Reel Bracket Assemblies and Associated Parts (Figure 32) A. Description Left-Hand Reel Bracket Assembly 694925-2 is used with the vertical reel bracket assembly supplied with the basic machine. This assembly is required when the terminal strip must enter the applicator from the left side of the machine.
  • Page 55 409-5128 Left-Hand Feed Reel Bracket Assembly 694925-2 Items 1 through 6 are in addition to items listed in Figure 18 for the vertical reel bracket assembly. Horizontal Reel Bracket Assembly 692613-1 (Items 7 through 16) 30° Mount For Use with Vertical Vertical Reel Bracket Assembly (Ref) Reel Bracket Assembly...
  • Page 56 409-5128 ITEM PART NUMBER DESCRIPTION - - - 694925-4 BRACKET ASSEMBLY, Vertical Reel, Dual Conversion Kit (See Illustration) 2-22789-6 SCREW, Wing Thumb, 1/4-20 X .750 in. L 457443-1 FLANGE, Reel 810578-1 FLANGE, Reel 465586-2 SHAFT, Reel 388648-5 STUD, Reel 2-21000-5 SCREW, Skt Hd Cap, 8-32 X .250 in.
  • Page 57 409-5128 Dual Conversion Kit 694925-4 Items 17 through 28 are added to the Vertical Reel Bracket Assembly (Ref) vertical reel bracket assembly. Refer to Figure 18, and remove Items 3, 4, and 6 through 10 before installing the kit. Frame (Ref) Reel Spreader Assembly 453596-1 For Use with Vertical Reel Bracket Assembly (Items 29 Through 41 and Reference)

  • Page 58: Modified Machines

    409-5128 11. MODIFIED MACHINES Modified Model "K" machines presented in this section are factory-prepared units that consist of a basic machine (as covered in Sections 1 through 9) plus one or more of the accessories described in Section 10. Each different type of modified machine has its own part number which distinguishes it from the other factory-modified versions and from the basic machine.
  • Page 59 409-5128 11.2. Machine 1-565435-7 (Figure 34) This modified machine accepts miniature quick-change applicators that mount on the machine at a 30° angle.The terminal strip enters the applicator from the right, but with the terminals in a vertical position. Several minor changes have been made to the basic machine, as covered in Section 1 through Section 9. Changes include the deletion of the vertical reel bracket assembly, and the addition of a horizontal reel bracket (on the right side), a base mount and plate for mounting the 30°...
  • Page 60 409-5128 Figure 34 (End) Rev Z 60 of 61...

  • Page 61: Rohs Information

    409-5128 11.3. Shut-Height Repair It is very important that the machine has the correct shut-height (ram bottomed) for miniature quick-change applicators to produce the specified crimp height. Each machine is adjusted at the factory prior to shipment and should never require further adjustment unless it is necessary to replace parts. Shut-height repair should NEVER be attempted without FIRST trying another applicator that is known to produce terminations of the correct crimp height.

This manual is also suitable for:

Basic amp-o-lectric k 1-471273-4

Table of Contents