Table of Contents
Advertisement
Contents
5
5
Installation
5.1
Rules for Installation..........................................................................................5-1
5.2
Installing the Terminal Module for the Power Supply Module...........................5-5
5.3
Installing Terminal Modules for the Interface Module and Electronics
Modules.............................................................................................................5-7
5.4
Installing the Bus Termination Module ............................................................5-10
5.5
Installing the Shield Contact............................................................................5-12
5.6
Fitting Slot Number Labels and Color Identification Labels ............................5-13
5.7
Replacing the Bus Interface Module and Terminal Box on the
Terminal Module..............................................................................................5-16
6
6
Wiring
6.1
General Rules and Regulations for Wiring........................................................6-1
6.2
Operate the ET 200iS with a Grounded-Neutral Supply...................................6-3
6.3
Electrical Design of the ET 200iS......................................................................6-5
6.4
Lightning and Overvoltage Protection ...............................................................6-6
6.4.1
Overview ...........................................................................................................6-6
6.4.2
The Lightning Protection Zone Concept ...........................................................6-7
6.4.3
Rules for the Interface between Lightning Protection Zones 0...1 ..................6-10
6.4.4
Rules for the Interfaces between Lightning Protection Zones 1...2
and higher .......................................................................................................6-12
6.4.5
Example of Protection from Overvoltage for Networked ET 200iS Stations...6-13
6.5
Wiring the ET 200iS ........................................................................................6-15
6.5.1
Wiring Rules for the ET 200iS.........................................................................6-15
6.5.2
Wiring Terminal Module TM-E30S44-iS with Screw Terminals ......................6-16
6.5.3
Wiring Terminal Module TM-E30C44-iS with Spring Terminals .....................6-17
6.5.4
Wiring Terminal Module TM-PS ......................................................................6-18
6.5.5
Wiring Terminal Module TM-IM.......................................................................6-20
6.5.6
Wiring Terminal Module TM-E ........................................................................6-22
6.5.7
Contacting the Cable Shields..........................................................................6-23
6.5.8
Grounding the DIN Rail ...................................................................................6-25
6.6
Inserting and Labeling the Power Supply, Interface Module, and
Electronics Modules ........................................................................................6-26
6.7
Setting the PROFIBUS Address .....................................................................6-31
7
7
Commissioning and Diagnostics
7.1
Overview of Defining the Configuration ............................................................7-1
7.2
Configuration .....................................................................................................7-5
7.3
Parameter Assignment......................................................................................7-7
7.4
Commissioning and Starting up the ET 200iS ................................................7-10
7.5
Reassign Parameters for the ET 200iS during Operation...............................7-14
7.6
Diagnostics Using the Process Image Input Table .........................................7-16
7.7
Status and Error LEDs on the IM 151-2..........................................................7-17
7.8
Diagnostics with STEP 5 and STEP 7 ............................................................7-22
7.8.1
Introduction......................................................................................................7-22
7.8.2
Reading out Diagnostic Information ................................................................7-22
7.8.3
Diagnostic Messages of the Electronics Modules...........................................7-24
7.8.4
Evaluating Interrupts from the ET 200iS (S7-DP Slave/ DPV1 Slave) ...........7-26
7.8.5
Structure of the Slave Diagnostic Information.................................................7-29
7.8.6
Station Status 1 to 3........................................................................................7-30
7.8.7
Master PROFIBUS Address............................................................................7-32
7.8.8
Vendor ID ........................................................................................................7-32
7.8.9
ID-Related Diagnostics ...................................................................................7-33
iv
5-1
6-1
7-1
ET 200iS Distributed I/O Station
A5E00087831-02
Advertisement
Table of Contents
