Parameter Group 9-** Profidrive - Danfoss VLT Profinet MCA 120 Operating Instructions Manual

Parameters

8.3 Parameter Group 9-** PROFIdrive

9-15 PCD Write Configuration
Array [10]
Option: Function:
Select the parameters to be assigned to PCD 3 to 10 of
the telegrams. The number of available PCDs depends
on the telegram type. The values in PCD 3 to 10 will
then be written to the selected parameters as data
values. Alternatively, specify a standard Profibus
telegram in 9-22 Telegram Selection.
9-16 PCD Read Configuration
Array [10]
Option: Function:
Select the parameters to be assigned to PCD 3 to 10 of
the telegrams. The number of available PCDs depends
on the telegram type. PCDs 3 to 10 contain the actual
data values of the selected parameters. For standard
Profibus telegram, see 9-22 Telegram Selection.
9-22 Telegram Selection
Option: Function:
Select a standard Profibus telegram
configuration for the frequency
converter, as an alternative to using
the freely configurable telegrams in
9-15 PCD Write Configuration and
9-16 PCD Read Configuration.
[1] Standard telegram 1
[101] PPO 1
[102] PPO 2
[103] PPO 3
[104] PPO 4
[105] PPO 5
[106] PPO 6
[107] PPO 7
[108] PPO 8
9-23 Parameters for Signals
Array [1000]
Read only
Option:
[0] None
[302] Minimum Reference
[303] Maximum Reference
[341] Ramp 1 Ramp Up Time
[342] Ramp 1 Ramp Down Time
MG90U302
Operating Instructions
9-23 Parameters for Signals
Array [1000]
Read only
Option:
[351]
[352]
[380]
[381]
[382]
[411]
[413]
[416]
[417]
[590]
[593]
[595]
[597]
[653]
[663]
[890]
[891]
[894]
[895]
[896]
[1500] Operating hours
[1501] Running Hours
[1502] Input kWh Counter
[1600] Control Word
[1601] Reference [Unit]
[1602] Reference [%]
[1603] Status Word
[1605] Main Actual Value [%]
[1609] Custom Readout
[1610] Input Power [kW]
[1611] Input Power [hp]
[1612] Motor Voltage
[1613] Frequency
[1614] Motor current
[1615] Frequency [%]
[1616] Torque [Nm]
[1617] Speed [RPM]
Function:
[1618] Motor Thermal
[1622] Torque [%]
This parameter
[1630] DC Link Voltage
contains a list of
signals available for
[1632] Brake Energy /s
selection in 9-15 PCD
[1633] Brake Energy /2 min
Write Configuration
[1634] Heatsink Temp.
and 9-16 PCD Read
[1635] Inverter Thermal
Configuration.
[1638] SL Controller State
[1639] Control Card Temp.
[1650] External Reference
[1652] Feedback[Unit]
[1653] Digi Pot Reference
[1654] Feedback 1 [Unit]
Danfoss A/S © Rev. 2014-02-27 All rights reserved.
Ramp 2 Ramp Up Time
Ramp 2 Ramp Down Time
Jog Ramp Time
Quick Stop Ramp Time
Starting Ramp Up Time
Motor Speed Low Limit [RPM]
Motor Speed High Limit [RPM]
Torque Limit Motor Mode
Torque Limit Generator Mode
Digital & Relay Bus Control
Pulse Out #27 Bus Control
Pulse Out #29 Bus Control
Pulse Out #X30/6 Bus Control
Terminal 42 Output Bus Control
Terminal X30/8 Output Bus Control
Bus Jog 1 Speed
Bus Jog 2 Speed
Bus Feedback 1
Bus Feedback 2
Bus Feedback 3
Function:
8
47
8