NATIX™
7-4. COMMANDS AND RESPONSES TABLE
The following table resumes all of the commands that are recognized as valid and the responses that will be returned to the
control device.
ASCII
RESPONSE
COMMAND
SELECTION COMMANDS
CC
CH
CN
CHN
cc
ch
cn
chn
G
TAKE
Z
FRZ
z
frz
INPUT COMMANDS
PC
PCH
PE
PEN
PL
PLD
PR
PRGB
PI
PSTD
PP
PPRC
OUTPUT COMMANDS
FM
OFTM
fp
oftp
FY
OSYN
fy
osyn
FS
SCRM
fs
scrp
pm
PAT
pp
pat
XR
REFR
xr
refr
NOTE:
COMMAND
DESCRIPTION
Selected input.
Input pre-selection for OUTPUT 1.
Pre-selected input (read only).
Input pre-selection for OUTPUT 2.
TAKE (transition).
FREEZE OUT 1.
FREEZE OUT 2.
Input selection for adjustment.
Input disabling (works with PC)
H sync load selection (works with PC). Rd/Wr
RGB input type selection (works with
PC command).
Input standard selection (works with
PC command).
VCR mode
Output formats selection (M).
Output formats selection (P).
Output sync selection (M).
Output sync selection (P).
Type of screen selection (M)
Type of screen selection (P)
Test pattern selection (M).
Test pattern selection (P).
Output 1 rate selection.
Output 2 rate selection.
(M) = output 1.
(P) = output 2.
Chapter 7 : REMOTE CONTROL PROGRAMMER'S GUIDE (continued)
TYPE
MIN MAX
0 = black
Rd
0
8
1 = input #1
Rd/Wr
0
8
2 = input #2
Rd
0
8
3 = input #3
4 = input #4
5 = input #5
Rd/Wr
0
8
6 = input #6
7 = input #7
8 = input #8
1 = start the transition (automatic reset at the
Rd/Wr
0
1
end of the effect duration).
0 = stop the transition (for holding effect).
Rd/Wr
0
1
0 = inactive
Rd/Wr
0
1
0 = inactive
0 = all inputs.
Rd/Wr
0
8
2 = input #2.............. 8 = input #8
Rd/Wr
0
1
0 = Input disable
0 = Hi-Z load
0
1
0 = SDTV composite
1 = SDTV S.VIDEO
2 = SDTV YUV
Rd/Wr
0
10
3 = SDTV RGBS (TTL) 9 = comp DVI
4 = SDTV RGsB (SOG) 10 = HDTV.
5 = SDTV RGBS (ana)
0 = NTSC/PAL/SECAM.
Rd/Wr
0
4
1 = NTSC.
2 = PAL.
Rd/Wr
0
1
0 = OFF
0 = SVGA 50Hz
1 = SVGA 60Hz
2 = SVGA 72Hz
Rd/Wr
0
20
3 = SVGA 75Hz
4 = XGA 50Hz
5 = XGA 60Hz
6 = XGA 72Hz
7 = XGA 75Hz
Rd/Wr
0
20
8 = SXGA 50Hz
9 = SXGA 60Hz
10 = SXGA 72Hz
Rd/Wr
0
2
0 = H &V sync.
1 = Composite sync.
Rd/Wr
0
2
Rd/Wr
0
1
0 = 4/3 screen
Rd/Wr
0
1
0 = 4/3 screen
0 = no pattern
Rd/Wr
0
6
3 = grey scale
Rd/Wr
0
6
6 = multi-burst.
Rd/Wr
0
8
0 = internal rate
2 = follow input #2... 8 = follow input #8
Rd/Wr
0
8
Rd/Wr = Read and write command.
Rd = Read only command.
VALUE
DESCRIPTION
1 = active.
1 = active.
1 = input #1
1 = Input enable.
1 = 75Ω load.
6 = SDTV SDI.
7 = computer (SOG)
8 = comp (HV or C.)
3 = SECAM
4 = Black & White.
1 = ON.
11 = SXGA 75Hz
12 = SXGA+ 50Hz
13 = SXGA+ 60Hz
14 = SXGA+ 72Hz
15 = SXGA+ 75Hz
16 = D-ILA 4/3 75Hz
17 = D-ILA 16/9 75 Hz
18 = WVGA 16/9 60Hz
19 = HDTV 720p 50Hz
20 = HDTV 720p 60Hz
2 = SOG
1 = 16/9 screen
1 = 16/9 screen
1 = centering 2 = color
4 = grid.
5 = softedge
1 = follow input #1
PAGE 43
Need help?
Do you have a question about the NATIX NTX8022A and is the answer not in the manual?
Questions and answers