Allen-Bradley PowerFlex 70 Reference Manual page 193

6-27
Digital Out 1
6-28
Start-Up
B. Dig Outputs
6-30
Enter choice for
Digital Out 1 Sel
Digital Out 1
Sel = ENUM
No
choice that
uses "Level"?
Yes
6-29
Start-Up
B. Dig Outputs
Enter value for
Dig Out 1 Level 6-31
6-49
Start-Up
C.Analog Outputs
Make a selection
<Anlgl Out 1>
Anlg Out 2
Done
Analog 1
6-50
Start-Up
C.Analog Outputs
Enter choice for
Analog Out 1 Sel
Output Freq
6-51
Start-Up
C.Analog Outputs
Enter choice for
Signal Type
<Voltage>
Current
6-52
Start-Up
C.Analog Outputs
Enter value for
Analog Out 1 Hi
10.000 Volt
x.xxxx < y.yyyy
6-53
Start-Up
C.Analog Outputs
Enter value for
Analog Out 1 Lo
0.0 Volt
x.xxxx < y.yyyy
Figure 55 PowerFlex 700 Vector Control Option Startup (7)
Start-Up
Go to 6-1 (C.Anlg
Done
B. Dig Outputs
Inputs)
Make a selection
<Digital Out 1>
Digital Out 2
Digital Out 3
Digital Out 3
Done
Start-Up
Digital Out 2
B. Dig Outputs
Enter choice for
Start-Up Digital Out 3 Sel
B. Dig Outputs
Enter choice for
Digital Out 2 Sel
Digital Out 3
Sel = ENUM
Digital Out 2
choice that
Sel = ENUM
uses "Level"?
choice that
uses "Level"?
Yes Start-Up
B. Dig Outputs
Enter value for
Start-Up
Dig Out 3 Level
B. Dig Outputs
Enter value for
No
Dig Out 2 Level
Go to 6-1 (D.
Done)
Analog 2
6-54
Start-Up
C.Analog Outputs
Enter choice for
Analog Out 2 Sel
Output Amps
6-55
Start-Up
C.Analog Outputs
Enter choice for
Signal Type
<Voltage>
Current
6-56
Start-Up
C.Analog Outputs
Enter value for
Analog Out 2 Hi
10.000 Volt
x.xxxx < y.yyyy
6-57
Start-Up
C.Analog Outputs
Enter value for
Analog Out 2 Lo
0.0 Volt
x.xxxx < y.yyyy
Rockwell Automation Publication PFLEX-RM001H-EN-P - June 2013
Flux Vector Start Up (Start,Stop,I/O [2])
6-32
6-35
Start-Up
Enter choice for
Signal type:
No
<Voltage>
Current
Torque Ref-
Anlg 1
Yes
6-33
6-36
Start-Up
C. Anlg Inputs
The next two
steps scale a
high torque with
a high analog
value.
6-37
Start-Up
C. Anlg Inputs
Enter value for
Analog In 1 Hi
10.0 V
x.xxxx < y.yyyy
6-38
Start-Up
C. Anlg Inputs
Enter value for
Torque Ref A Hi
100.0 %
x.x < y.y
6-39
Start-Up
C. Anlg Inputs
The next two
steps scale a
low torque with
a low analog
value.
6-40
Start-Up
C. Anlg Inputs
Enter value for
Analog In 1 Lo
10.0 V
x.xxxx < y.yyyy
6-41
Start-Up
C. Anlg Inputs
Enter value for
Torque Ref A Hi
100.0 %
x.x < y.y
Start-Up
6-34
Start-Up
C. Anlg Inputs
Enter choice for
Input Signal
<Analog Input 1>
Analog Input 2
Anlg 1 Anlg 2
6-42
Start-Up
C. Anlg Inputs
Enter choice for
Signal type:
<Voltage>
Current
Torque Ref-
Anlg 2
6-43
Start-Up
C. Anlg Inputs
The next two
steps scale a
high torque with
a high analog
value.
6-44
Start-Up
C. Anlg Inputs
Enter value for
Analog In 2 Hi
10.0 V
x.xxxx < y.yyyy
6-45
Start-Up
C. Anlg Inputs
Enter value for
Torque Ref A Hi
100.0 %
x.x < y.y
6-46
Start-Up
C. Anlg Inputs
The next two
steps scale a
low torque with
a low analog
value.
6-47
Start-Up
C. Anlg Inputs
Enter value for
Analog In 2 Lo
10.0 V
x.xxxx < y.yyyy
6-48
Start-Up
C. Anlg Inputs
Enter value for
Torque Ref A Hi
100.0 %
x.x < y.y
Go to 6-1 (D.Anlg
Outputs)
193