Table Of Contents - Agilent Technologies 4339B User Manual

Contents
1. Preparation for Use
In This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
To Set Power LINE Voltage . . . . . . . . . . . . . . . . . . . . . . . . . .
To Set Power LINE Frequency . . . . . . . . . . . . . . . . . . . . . . . .
2. Operating the 4339B
In This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
To Reset 4339B to its Default Settings . . . . . . . . . . . . . . . . . . . . .
To Connect Test Fixture . . . . . . . . . . . . . . . . . . . . . . . . .
16008B Resistivity Cell . . . . . . . . . . . . . . . . . . . . . . . . . . .
16117B Low Noise Test Lead . . . . . . . . . . . . . . . . . . . . . . . .
16339A Component Test Fixture . . . . . . . . . . . . . . . . . . . . . .
To Perform Calibration|Canceling internal measurement errors . . . . . . . .
To Set Test Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
To Set Current Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
To Perform OPEN Correction
|Canceling the stray admittance in parallel with the DUT . . . . . . . . .
If \Out Of Limit" is displayed . . . . . . . . . . . . . . . . . . . . . . . .
To Connect DUT . . . . . . . . . . . . . . . . . . . . . . . . . . . .
To Select Measurement Parameter . . . . . . . . . . . . . . . . . . . . . .
Setting the Parameters for Resistivity Measurement . . . . . . . . . . . . .
Setting Thickness of the DUT . . . . . . . . . . . . . . . . . . . . . . .
Setting the Electrode Size . . . . . . . . . . . . . . . . . . . . . . . .
To Select Measurement Range . . . . . . . . . . . . . . . . . . . . . . . .
Auto Range mode|Automatically selecting the optimum measurement range .
Hold Range mode|Holding the measurement range of your choice . . . . . .
To Select Measurement Time Mode . . . . . . . . . . . . . . . . . . . . . .
To Set Averaging Rate|Stabilizing the measurement result . . . . . . . . . . .
To Select Trigger Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . .
To Set Trigger Delay Time . . . . . . . . . . . . . . . . . . . . . . . . . .
To Use Deviation Measurement Function . . . . . . . . . . . . . . . . . . .
Setting the Deviation Reference Values . . . . . . . . . . . . . . . . . . .
Selecting the Deviation Mode . . . . . . . . . . . . . . . . . . . . . . . .
To Use Comparator Function . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the Limit Values . . . . . . . . . . . . . . . . . . . . . . . . . .
Sorting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
To Select Display Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . .
To Select Beeper Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . .
To Use Contact Check Function |Monitoring the connection of test electrodes and
DUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
To Print Measurement Data . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1
1-1
1-1
1-2
2-1
2-2
2-2
2-2
2-3
2-3
2-4
2-4
2-4
2-5
2-5
2-6
2-6
2-7
2-7
2-7
2-8
2-8
2-8
2-8
2-9
2-9
2-9
2-10
2-10
2-10
2-11
2-11
2-11
2-12
2-13
2-13
2-14
2-14
Contents-1