As20Wrf/Brf Thermostat - Functions & Parameters - Salus SG888ZB System Manual

Section 7
AS20WRF/BRF Thermostat – Functions & Parameters
Function
d00 Select Units
d01 Heating Control
d02 Temp . Offset
d03 Outdoor Sensor
d04 External Sensor
d05 Cooling Control
d06 Actuator Type
d07 Valve Protection
d08 Frost Setpoint 41ºF (5 .0ºC)
d09 Hour Format
d10 Not Applicable
d11 Daylight Savings
Max . Heat
d12 95ºF (35ºC)
Setpoint
d13 Max . Cool Setpoint
Floor Sensor High
d14 81°F (27°C)
Limit (heating)
Floor Sensor Low
d15 50°F (10°C)
Limit (heating)
Floor Sensor Low
d16
Limit (cooling)
d17 Preset Programs
Heat/Cool Mode
d18
Selection
Setting Device Parameters
Parameters
Default Value
0
0
1
0
0 1
2
-6ºF to +6ºF
0
(-3 .0ºC to +3 .0ºC )
0
0 1
3
0
0
1
1
2
2
0
1
1
0
1
1
41ºF to 63ºF
(5 .0ºC -to 17ºC )
0
1
1
N/A N/A
0
1
1
42ºF to 95ºF
(17 .5ºC to 35 .0ºC)
41ºF to 104ºF
41ºF (5ºC)
(5 .0ºC to 40 .0ºC)
59ºF to 113ºF
(15 .0ºC to 45 .0ºC)
43ºF to 104ºF
(6 .0ºC to 40 .0ºC)
43ºF to 113ºF
43°F (6°C)
(6 .0ºC to 45 .0ºC)
1 0-1
0
0
1
SI Metric Units - °C
US Customary Units - °F
Time Proportional & Integral (TPI)
ON/OFF – 0 .5°C (1 .0°F) Increments
ON/OFF – 1 .0°C (2 .0°F) increments
Room Temperature Offset (1 .0°F/0 .5°C increments)
Outdoor Sensor not connected to S1/S2
Outdoor Sensor or Ext . (d04) connected (10 kΩ)
Not Used
d03 = 1, Ext . air sensor active, Int . sensor inactive
d03 = 1, Ext . floor sensor active, Int . sensor active
ON/OFF – 1 .0°F (0 .5°C) increments
ON/OFF – 2 .0°F (1 .0°C ) increments
NO Normally Open
NC Normally Closed
ARV10RFM Valve Exercise Disable
ARV10RFM Valve Exercise Enable
Minimum room temperature for frost protection and holiday mode
12 Hour Time Format (eg . 5:00 pm)
24 Hour Time Format (eg . 17:00)
This function is not applicable
Daylight Savings Time (DST) Off
Daylight Savings Time (DST) On
Maximum setpoint for heating mode
Maximum setpoint for cooling mode
Disable heat demand when floor temperature is above high limit .
Increment: 1°F (0 .5°C)
Provide heat demand when floor temperature is below low limit .
Increment: 1°F (0 .5°C)
Disable cooling demand when floor temperature is below low limit .
Increment: 1°F (0 .5°C)
Select program . Once selected, the selected program will overwrite
the present program .
Disable Heat/Cool selection
Enable Heat/Cool selection
Description
7 .3