Download Print this page

IBM Turbo 16/4 Token-Ring PC Card 2 User Manual

Hide thumbs

Advertisement

Quick Links

Turbo 16/4 Token-Ring PC Card 2
User's Guide

Advertisement

loading

  Related Manuals for IBM Turbo 16/4 Token-Ring PC Card 2

  Summary of Contents for IBM Turbo 16/4 Token-Ring PC Card 2

  • Page 1 Turbo 16/4 Token-Ring PC Card 2 User’s Guide...
  • Page 3 Turbo 16/4 Token-Ring PC Card 2 User’s Guide...
  • Page 4 IBM Corporation PO Box 12195 RESEARCH TRIANGLE PARK NC 27709-9990 When you send information to IBM, you grant IBM a nonexclusive right to use or distribute the information in any way it believes appropriate without incurring any obligation to you.
  • Page 5: Table Of Contents

    ..... . . 33 Using LANAID to Configure the PC Card ....34 © Copyright IBM Corp. 1997, 1999...
  • Page 6 World Wide Web ..... . . 50 IBM Product Support ..... 50 Troubleshooting and Error Codes .
  • Page 7 Appendix G. Notices and Warranty ....95 Notice to Users in the United Kingdom ....95 Electronic Emission Notices .
  • Page 8 Turbo 16/4 Token-Ring PC Card 2...
  • Page 9: Preface

    Preface This manual contains the information you need to install and use your PC Card. Unless specified, all references in this book to the PC Card apply to the IBM Turbo 16/4 Token-Ring PC Card 2. On this CD-ROM are the installation aids, device drivers, and documentation for the PC Card.
  • Page 10: Related Information

    NTS/2 LAN Adapter and Protocol Support Configuration Guide , S96F-8489 v LAN Technical Reference: Token-Ring Network Shared-RAM , SC30-3588 v IBM Token-Ring Adapter Features , available on the IBM Turbo 16/4 Token-Ring PC Card 2 CD-ROM v IBM Networking home page on the World Wide Web: www.networking.ibm.com...
  • Page 11: Safety Information

    SD21-0030. Hierin wordt beschreven hoe u electrische apparatuur op een veilige manier moet bekabelen en aansluiten. Gevaar Voordat u begint met het installeren van dit produkt, dient u eerst de veiligheidsrichtlijnen te lezen die zijn vermeld in de publikatie Caution: Safety © Copyright IBM Corp. 1997, 1999...
  • Page 12 Information - Read This First , SD21-0030. In dit boekje vindt u veilige procedures voor het aansluiten van elektrische appratuur. Vorsicht: Bevor mit der Installation des Produktes begonnen wird, die Sicherheitshinweise in Achtung: Sicherheitsinformationen—Bitte zuerst lesen, IBM Form SD21-0030. Diese Veröffentlichung beschreibt die Sicherheitsvorkehrungen für das Verkabeln und Anschließen elektrischer Geräte.
  • Page 13 Perigo: Antes de iniciar a instalação deste produto, leia as informações de segurança Cuidado: Informações de Segurança — Leia Primeiro , SD21-0030. Este documento descreve como efectuar, de um modo seguro, as ligações eléctricas dos equipamentos. Peligro: Antes de empezar a instalar este producto, lea la información de seguridad en Atención: Información de Seguridad —...
  • Page 14 Vigyázat: Mielôtt megkezdi a berendezés üzembe helyezését, olvassa el a “Caution: Safety Information— Read This First, SD21-0030 könyvecskében leírt biztonsági információkat. Ez a könyv leírja, milyen biztonsági intézkedéseket kell megtenni az elektromos berendezés huzalozásakor illetve csatlakoztatásakor. Turbo 16/4 Token-Ring PC Card 2...
  • Page 15 xiii Safety Information...
  • Page 16 Turbo 16/4 Token-Ring PC Card 2...
  • Page 17: Chapter 1. Introduction

    Chapter 1. Introduction The IBM Turbo 16/4 Token-Ring PC Card 2 (referred to as PC Card ) is a credit-card-sized adapter that provides an interface between computers and Token-Ring networks. It is part of the shared RAM family of adapters. The PC Card is designed for computers with slots that comply with the standards for the Personal Computer Memory Card International Association (PCMCIA) Release 2.1, Type II...
  • Page 18: Stealth Mode

    Turbo PC Cards. That new hardware feature is referred to as Stealth Mode and can be used in the Turbo 16/4 Token-Ring PC Card 2 to remove power from the card by removing only the cable. The operating system will not sense the presence of the card in the slot with the cable detached.
  • Page 19: Chapter 2. Installation

    Kit Contents Your kit contains the following items: v IBM Turbo 16/4 Token-Ring PC Card 2 (also called PC Card ) v Token-Ring PC Card cable, P/N 38H7044. (The standard cable uses an RJ-45 connector for use with UTP network wiring.) v One IBM Turbo 16/4 Token-Ring PC Card 2 CD-ROM.
  • Page 20 The software might have been provided with your computer or operating system. See page 38 for a description of these services. Return to page 3 to continue. Step 2 of the Installation Checklist is now complete. Turbo 16/4 Token-Ring PC Card 2...
  • Page 21: Chapter 3. Inserting And Removing The Pc Card

    IBM Token-Ring PC Cards. Note: Verify that you are using the correct STP connector. The correct STP connector and PC Card cable have the code number 100 on the connectors that attach to each other. © Copyright IBM Corp. 1997, 1999...
  • Page 22: Removing The Pc Card

    Note: If you are using Card and Socket Services, you may be able to use hot-pluggability features with your PC Card. See “Hot-Pluggability and Suspend/Resume Issues” on page 7 for more information. Follow these steps to remove the PC Card: Turbo 16/4 Token-Ring PC Card 2...
  • Page 23: Hot-Pluggability And Suspend/Resume Issues

    The IBM Turbo 16/4 Token-Ring PC Card 2 appears to be removed physically from a system when the cable is removed. The PC Card appears to the system to be inserted when its cable is reattached to the PC Card.
  • Page 24: Dos Odi Hot-Pluggability And Suspend/Resume

    If you want to do something like this, you must first remove the card and then suspend. You can then resume later and reinsert the card later. Turbo 16/4 Token-Ring PC Card 2...
  • Page 25: Chapter 4. Software Installation

    1. Get the latest level of LAN driver updates for your operating system to ensure that your code is at the latest level. 2. Be sure that your IBM Turbo 16/4 Token-Ring PC Card 2 has already been installed in your computer. If it has not, follow the instructions in “Chapter 3.
  • Page 26: Novell Installation

    If your Card Services is version 5.00 or higher, you do not need to worry about this parameter. CS20TOK.EXE Configuration CS20TOK.EXE is a small software program that configures the PC Card socket controller to allocate resources (memory, I/O Ports, interrupts, DMA channels, and Turbo 16/4 Token-Ring PC Card 2...
  • Page 27: Novell Netware 3.12 Server

    1. Create a diskette containing the extracted files from the NETWARE.EXE package file on the IBM Turbo 16/4 Token-Ring PC Card 2 CD-ROM. 2. Refer to Novell’s Installation and Upgrade manual for installation instructions. Follow the procedure for the installation of Novell NetWare 3.12 until the section titled ″Load LAN Drivers″...
  • Page 28 Enter the following commands at the server prompt. You might be prompted to perform a file overwrite; it is OK to overwrite these files. COPY A:\NOVELL\NETWARE\NBI31X.NLM C:\SERVER.312 COPY A:\NOVELL\NETWARE\MSM31X.NLM C:\SERVER.312 COPY A:\NOVELL\NETWARE\TOKENTSM.NLM C:\SERVER.312 COPY A:\NOVELL\NETWARE\IBMTOKEN.LAN C:\SERVER.312 COPY A:\NOVELL\NETWARE\IBMTOKEN.LDI C:\SERVER.312 Turbo 16/4 Token-Ring PC Card 2...
  • Page 29 1. Create a diskette containing the extracted files from the NETWARE.EXE file on the IBM Turbo 16/4 Token-Ring PC Card 2 CD-ROM. 2. Install the patches obtained earlier now. Make sure to select the v3.31 ODI LAN Updates for Hardware if given the opportunity.
  • Page 30: Novell Netware 4.11 Server

    Novell patches. It is for information only, and can be ignored. 1. Create a diskette containing the extracted files from the NETWARE.EXE package file on the IBM Turbo 16/4 Token-Ring PC Card 2 CD-ROM. 2. When you see INSTALL Found the following: IBM Turbo 16/4 Token-Ring PC Card 2 xxxx xxxx xxxx , press Enter.
  • Page 31 3. Press ALT-ESC to toggle to the server console, and enter the following LOAD statements (make sure that the diskette that you created in step 1 is inserted in drive A): LOAD A:\NOVELL\NETWARE\MSM.NLM LOAD A:\NOVELL\NETWARE\TOKENTSM.NLM 4. Press ALT-ESC to toggle back to the INSTALL panel. 5.
  • Page 32 1. Create a diskette containing the extracted files from the NETWARE.EXE file on the IBM Turbo 16/4 Token-Ring PC Card 2 CD-ROM. 2. Be sure that your IBM Turbo 16/4 Token-Ring PC Card 2 is already in your computer. If it is not, follow the instructions in “Chapter 2. Installation” on page 3.
  • Page 33: Novell Netware 5.0 Server

    1. Create a device driver installation diskette. Create a diskette containing the extracted files from the NETWARE.EXE package file on the IBM Turbo 16/4 Token-Ring PC Card 2 CD-ROM. 2. During the installation program, when you get to Select a Storage Device and a Network Board: v Select and configure the storage device...
  • Page 34 1. Create a diskette that contains the extracted files from the NETWARE.EXE package file on the IBM Turbo 16/4 Token-Ring PC Card 2 CD-ROM. 2. At the server console prompt, enter NWCONFIG 3. Select Driver Options > Configure network drivers.
  • Page 35: Novell Client Dos/Windows 3.1X

    32–bit ODI driver: x:\novell\netware where x is your CD-ROM drive letter. The panel should say IBM Token-Ring PCMCIA Press Enter, configure the parameters, and press F10 to save and continue. 8. At the Installation Configuration Summary panel, confirm that the values are what you selected, and press F10 to save and continue.
  • Page 36: Novell Netware Server Driver Parameters

    MLID and the upper layers. The MSB designation forces non-canonical addresses to be passed (this is the default for Token-Ring media). Valid values: TOKEN-RING or TOKEN-RING_SNAP The default is TOKEN-RING. Turbo 16/4 Token-Ring PC Card 2...
  • Page 37 Table 4. Novell NetWare Driver Parameters (continued) Parameter Explanation FULLDUPLEX= This keyword permits the IBMTOKEN LAN driver to activate Token-Ring full-duplex operation supported by the PC Card and the NetWare server environment. Valid values: YES, NO The default is YES. MEM1= The MEM1 keyword is needed if you are using a Card Services version earlier than version 5.00.
  • Page 38 Route Switching Holding Time. This parameter specifies the Route Switching information holding time value. This determines how often a remote station must refresh its Route Switching information which pertains to this station. Valid values: 2 to 20 The default is 20. Turbo 16/4 Token-Ring PC Card 2...
  • Page 39: Windows Installation

    Windows Installation Windows 95 and Windows 98 1. Insert the IBM Turbo 16/4 Token-Ring PC Card 2 in your computer and switch it on. When Windows loads, it will alert you to the fact that new hardware was found in your computer. If it does not, see “Troubleshooting and Error Codes” on page 50.
  • Page 40: Windows Nt 3.51

    Cardbus controller for Windows 95 OSR2. Windows NT 3.51 1. Insert the IBM Turbo 16/4 Token-Ring PC Card 2 in your computer and switch it on. When Windows NT loads, login to the computer and open the control panel.
  • Page 41: Windows Nt 4.0

    Windows NT 4.0 1. Insert the IBM Turbo 16/4 Token-Ring PC Card 2 in your computer and switch it on. When Windows NT loads, login to the computer and open the control panel. Double-click the Network icon.
  • Page 42: Os/2 Installation

    5. On the Configure panel, make sure that LAN adapters and protocols is preselected and then select Configure at the bottom of the panel. 6. In the Configuration panel, in the Network Adapters group box, select IBM Turbo 16/4 Token-Ring PC Card 2 and select ADD.
  • Page 43: Os/2 Ndis 2 Device Driver Using Other Installation Programs

    If you experience problems go to “Appendix B. Problem Determination” on page 49 . OS/2 NDIS 2 Device Driver Using Other Installation Programs IBM TCP/IP for OS/2 is an example of a product that provides driver installation programs. 1. Insert the CD-ROM in the drive.
  • Page 44: Odi 16-Bit Client

    NetWare Client for DOS and MS Windows diskettes. 1. Create a diskette containing the extracted files from the DOSODI.EXE file on the IBM Turbo 16/4 Token-Ring PC Card 2 CD-ROM. 2. Insert the NetWare Client for DOS and MS Windows Disk 1 into the appropriate drive.
  • Page 45: Odi 16-Bit Client Parameters

    9. Follow the instructions presented to finish the installation. Note: If source routing is required, edit the STARTNET.BAT file that is in the client directory (usually c:\nwclient) and add the following line after the IPXODI statement. c:\nwclient\route 10. Shut down and restart your computer for all changes to take effect. 11.
  • Page 46 MAX FRAME SIZE This option sets the maximum number of bytes that can be put on the wire by the Turbo 16/4 Token-Ring PC Card 2. The number must be a multiple of 8 and include the number of bytes for the...
  • Page 47 Table 5. ODI 16–bit Client Parameters (continued) Parameter Explanation RECEIVEBUFFERSIZE This parameter can be set to a value from 192 to 2048, inclusive. Any value smaller than 192 is changed to 192. Any value larger than 2048 is changed to 2048. Numbers between 192 and 2048 that are not on an eight-byte boundary are rounded up to the next higher eight-byte boundary.
  • Page 48 Turbo 16/4 Token-Ring PC Card 2...
  • Page 49: Chapter 5. Lanaid

    LANAID is a software tool that is shipped on the IBM Turbo 16/4 Token-Ring PC Card 2 CD-ROM. Use LANAID to automatically configure the appropriate system files for the IBM Turbo 16/4 Token-Ring PC Card 2 to work with any of the network operating systems that are listed below.
  • Page 50: Using Lanaid To Configure The Pc Card

    If you are not using Card and Socket Services in Autoset mode, you must ensure that the values that you select for Interrupt and I/O address do not conflict with those for other PC Cards installed in your computer. Use the Turbo 16/4 Token-Ring PC Card 2...
  • Page 51: Command Line Invocation Of Lanaid

    Change push button to select from the allowable values yourself. The Hardware folder shows parameters of the computer system that you cannot set, but that might be useful. Select the Store push button. When you finish with the panels, press the Done button and you will be returned to the main panel.
  • Page 52 Turbo 16/4 Token-Ring PC Card 2...
  • Page 53: Chapter 6. Point Enablers And Card Services

    Services Socket Controller Socket Controller Point Connectivity Enablers These are small programs that provide an interface directly to the PC Card controller; therefore, they must be written to support a particular type of controller. © Copyright IBM Corp. 1997, 1999...
  • Page 54: Advantage

    One point enabler is supplied for this PC Card: POINTTR.EXE For computers with Intel 32365SL PCMCIA controller chip sets or any controller that is designed to be compatible. These include the IBM ThinkPad, Toshiba 4500 and later, and many other makes. Notes: 1.
  • Page 55: Advantages

    This program is a Card Services Enabler that uses Card and Socket Services to configure the IBM Turbo 16/4 Token-Ring PC Card 2. As with other enablers, you must specify the resources desired for the PC Card, and they must agree with the settings of the Token-Ring device driver for the system to work correctly.
  • Page 56: Autoset Mode

    For the point enabler, the required exclusions are shown in the example below (using EMM386, this is done using the X= parameter): For enhanced mode: DEVICE=C:\POINTTR.EXE SA RS=4 MMIO=D000 IRQ=9 SRAM=D000,4 WS=0 DEVICE=C:\DOS\HIMEM.SYS DEVICE=C:\DOS\EMM386.EXE 1024 RAM X=D000-D1FF For compatibility mode: Turbo 16/4 Token-Ring PC Card 2...
  • Page 57: Memory Managers With Card And Socket Services

    This will prohibit the memory manager from also using that same space. For IBM CS, the /MA is used to specify the range of memory the PC Cards and Card Services use. The parameter is added to the Resource Map Utility line in your CONFIG.SYS.
  • Page 58: Expanded Memory Specification

    So, no PC Cards should be set to use memory in the range C0000–CFFFF. 3. Using IBM Card Services, you can set the /MA option such that a 64-KB block is free for the EMS page frame. A sample memory manager line in your CONFIG.SYS is:...
  • Page 59 Note: Because of the /MA option, IBM CS will use memory in the range D0000–DBFFF only. The FRAME= parameter sets the base address of the EMS page frame (the page frame uses C0000–CFFFF). So, no PC Cards should be set to use memory in the range C0000–CFFFF.
  • Page 60 Turbo 16/4 Token-Ring PC Card 2...
  • Page 61: Appendix A. Cd-Rom Content And Software Packages

    Appendix A. CD-ROM Content and Software Packages The CD-ROM contains PC Card drivers, supporting applications, publications, technical tips, and frequently asked questions related to the IBM Turbo 16/4 Token-Ring PC Card 2. A nagivational tool is provided to assist in accessing the contents of the CD-ROM.
  • Page 62: Diskette Images

    Windows 95/98/NT — Diskette 2 v DMIWINB.EXE v Windows 95/98/NT — Diskette 3 v DMIWINC.EXE IBM LAN Client v IBM LAN Client — Diskette 1 v LCDISK1.EXE v IBM LAN Client — Diskette 2 v LCDISK2.EXE v IBM LAN Client — Diskette 3 v LCDISK3.EXE...
  • Page 63: Product Documentation

    To access the product documentation, insert the CD-ROM into the CD-ROM drive of your computer and point your Web browser to x:\startcd.htm (where x is your CD-ROM drive letter). Select IBM Networking Web Site or CD-ROM and then Downloads. Select Target Operating System and then select the User’s Guide or Token-Ring Adapter Features .
  • Page 64 Turbo 16/4 Token-Ring PC Card 2...
  • Page 65: Appendix B. Problem Determination

    MMIO memory and the SRAM memory are located. Be sure that the enabler settings and the settings of the LAN driver coincide. By the use of parameters on the command line of the enabler and the parameters for © Copyright IBM Corp. 1997, 1999...
  • Page 66: Questions, Problems

    The IBM Token-Ring Shared RAM Adapter UAA (BIA) is xxx . Explanation: Information only. User Action: None. IBMTOKEN-xx-203 The IBM Token-Ring Shared RAM Adapter is using an LAA of xxx . Explanation: Information only. User Action: None. Turbo 16/4 Token-Ring PC Card 2...
  • Page 67 Error Code Explanation and Action IBMTOKEN-xx-204 Revision level xxx of the IBM Token-Ring Shared RAM Adapter is incompatible with this driver version. Explanation: The Revision ID of the IBM Token-Ring Shared RAM Adapter is not one that is supported by this version of the device driver.
  • Page 68 (wall plate). Turn the computer off and then on again to restart the machine. If the problem persists, contact your customer service center. Turbo 16/4 Token-Ring PC Card 2...
  • Page 69 Error Code Explanation and Action IBMTOKEN-xx-211 A possible lobe wire failure was detected while attempting to insert into the network. Explanation: The adapter is not correctly connected to the Token-Ring network. User Action: Check that the cable is securely attached to both the adapter and to the Token-Ring network.
  • Page 70 Explanation: The Token-Ring network is not functioning correctly. User Action: Contact your local network administrator to determine the status of your network, or try connecting again at a later time. Turbo 16/4 Token-Ring PC Card 2...
  • Page 71 Error Code Explanation and Action IBMTOKEN-xx-218 A duplicate network address was detected while attempting to insert into the network. Explanation: The address specified for the NetAddress configuration parameter is being used by another adapter (or ring station) on the network. User Action: Modify the configuration file to change the NetAddress parameter value being used for...
  • Page 72 (wall plate). Turn the computer off and then on again to restart the machine. If the problem persists, contact your customer service center. Turbo 16/4 Token-Ring PC Card 2...
  • Page 73 Error Code Explanation and Action IBMTOKEN-xx-223 The adapter cannot be opened in AutoSense mode if it is the only active station on the network. Explanation: The DataRate configuration parameter is set to AUTO (which is also the default value if the parameter is not specified), but the adapter is the first station to open on the Token-Ring network.
  • Page 74 If the diagnostics indicates that the adapter is not defective then record this message number and contact your customer service center. IBMTOKEN-xx-227 The IBM Token-Ring Shared RAM Adapter opened at xxx Mbps, half duplex. Explanation: Information only. User Action: None.
  • Page 75 User Action: None. IBMTOKEN-xx-234 Adapter full-duplex operation has now been activated. Explanation: Information only. User Action: None. IBMTOKEN-xx-240 IBM Token-Ring Shared RAM Adapter Explanation: Information only. User Action: None. IBMTOKEN-xx-301 ODI 3.3 and Above HSM Explanation: Information only. User Action: None.
  • Page 76: Windows 95 And Windows 98

    PC Card not to function. If you find that your PC Card is not functioning, follow this procedure. 1. Click Start. 2. Go to the Settings menu selection and click Control Panel. 3. Click System. 4. Click the Device Manager tab. Turbo 16/4 Token-Ring PC Card 2...
  • Page 77: Windows Nt

    2. From the Device Manager, look for a yellow or red circle with an exclamation point beside an entry for the IBM Turbo 16/4 Token-Ring PC Card 2. If you see this, then double-click the adapter. The properties dialog for the adapter will now be displayed.
  • Page 78: Os/2 Ndis Error Codes

    A value specified for a parameter in PROTOCOL.INI is not valid. Explanation: The value provided for the parameter is not the correct type or is not a valid value. User Action: Change the value for the parameter in PROTOCOL.INI. Turbo 16/4 Token-Ring PC Card 2...
  • Page 79 LTG0025I A configuration error was found in PROTOCOL.INI. Explanation: Conflicting parameter values were found while the installation program was processing the IBM Token-Ring Network Driver section of PROTOCOL.INI. User Action: Examine the configuration parameters and correct the conflicting values in PROTOCOL.INI.
  • Page 80 PC Card. Explanation: The node address defined is not valid. User Action: Specify a valid node address. Refer to the IBM Token-Ring Network Architecture Reference (SC30–3374) for node address restrictions. Turbo 16/4 Token-Ring PC Card 2...
  • Page 81 Error Code Explanation and Action LTG0033I The receive buffer length defined is not valid. Explanation: The PC Card was not opened. The receive buffer length defined in PROTOCOL.INI is not valid. The value specified must be greater than the allowable maximum, less than the allowable minimum, or not a multiple of 8.
  • Page 82 1. Check and secure all cable connections between your PC Card and the MSAU. Correct any related problems and try the operation again. 2. If there are no related problems, run the diagnostics; then, try the operation again. Turbo 16/4 Token-Ring PC Card 2...
  • Page 83 Error Code Explanation and Action LTG0042I An open error occurred during the physical insertion phase. Explanation: The PC Card has detected one of the following open errors while trying to insert into the LAN: v Ring failure v Ring beaconing v Timeout User Action: Perform the following steps:...
  • Page 84 2. If there are no related problems, run the diagnostics; then, try the operation again. 3. If the problem persists, print or save the LANTRAN.LOG file and contact your LAN administrator. Turbo 16/4 Token-Ring PC Card 2...
  • Page 85 Error Code Explanation and Action LTG0051I The open error type is function failure. Explanation: The PC Card has detected a lobe media failure while trying to open the PC Card. User Action: Perform the following steps: 1. Check and secure all cable connections between your PC Card and the multistation access unit (MSAU).
  • Page 86 2. If there are no related problems, run the diagnostics; then, try the operation again. 3. If the problem persists, print or save the LANTRAN.LOG file and contact your LAN administrator. Turbo 16/4 Token-Ring PC Card 2...
  • Page 87 Error Code Explanation and Action LTG0057I The open error type is ring beaconing. Explanation: The PC Card has detected a monitor contention failure or has received a beacon frame from the ring while trying to open the PC Card. User Action: Perform the following steps: 1.
  • Page 88 Make sure that no other PC Cards are using the range of I/O ports that the adapter needs. For a primary PC Card the range is A20–A23. For a secondary PC Card the range is A24–A27. Turbo 16/4 Token-Ring PC Card 2...
  • Page 89 Error Code Explanation and Action LTG0084E Token-Ring Credit Card Request IRQ failed. Explanation: Card Services would not give IBMTOKCS access to the interrupt request (IRQ) line it requested. User Action: Make sure that no other PC Cards are using the IRQ requested. IBMTOKCS defaults to IRQ 9.
  • Page 90 Make sure that you have Card Services 2.0 (PCMCIA.SYS) correctly installed. LTG0091E Card Services could not be found. Explanation: User Action: Add the appropriate statements to your CONFIG.SYS file so that Card Services will be installed. Turbo 16/4 Token-Ring PC Card 2...
  • Page 91 Error Code Explanation and Action LTG0093E No sockets were found by Card Services. Explanation: The Card Services function GetCardServicesInfo reported that there are no sockets in your computer. This can be for any of the following reasons: 1. Socket Services is not installed or is installed incorrectly.
  • Page 92: Dos Ndis Error Codes

    Resolve the specific error message that accompanies this message. In addition, ensure that the Protocol Manager device driver, PROTMAN.DOS, exists, and that a DEVICE statement for it exists in the CONFIG.SYS file. Turbo 16/4 Token-Ring PC Card 2...
  • Page 93: Odi 16-Bit Client Error Codes

    ODI 16-bit Client Error Codes Error Code Explanation and Action TOKENCS-DOS-32 Driver registered as a NESL Suspend Class producer. Explanation: This is an informational only message. User Action: No action is required. TOKENCS-DOS-33 Driver registered as a NESL Resume Class producer. Explanation: This is an informational only message.
  • Page 94 Change the maximum frame size to a valid value. TOKENCS-DOS-229 The MAX FRAME SIZE in NET.CFG file is too small (Min=632). Explanation: The maximum frame size is too small. User Action: Increase the maximum frame size to a valid value. Turbo 16/4 Token-Ring PC Card 2...
  • Page 95 Error Code Explanation and Action TOKENCS-DOS-230 The specified MAX FRAME SIZE in NET.CFG is not a multiple of 8. Explanation: The maximum frame size has been set to a value that is not valid. User Action: Change the MAX FRAME SIZE to a multiple of 8.
  • Page 96 4 or 16 Mbps. The DATA RATE keyword is used to set the speed. User Action: (no message) Please insert an IBM Turbo 16/4 Token-Ring PC Card 2 or press Esc to avoid loading the driver. Explanation: This message occurs when you have not...
  • Page 97: Appendix C. Running The Diagnostics Program

    1. Insert the Diagnostics and LANAIDC diskette. 2. Switch ON the power to the computer. 3. At the DOS Menu, select 2, IBM Turbo 16/4 Token-Ring PC Card Extended Diagnostics. 4. Follow the instructions as they appear. You will be prompted to select a test option.
  • Page 98: Open Errors

    Adapter open, should be closed Required parameters not provided Command cancelled, unrecoverable failure (see open error codes to isolate problem) Inadequate receive buffers Incorrect MAC address Incorrect adapter receive buffer length Incorrect adapter transmit buffer length Turbo 16/4 Token-Ring PC Card 2...
  • Page 99: Open Error Codes

    Open Error Codes If the open provides a return code of 7, there will be a corresponding error code. The open errors are returned in 2 bytes. The high-order byte is always 0 and the low-order byte contains the following information: 1.
  • Page 100 Address Verification, Remove Received: The PC Card 2a and 4 has received a remove ring station MAC frame, indicating that a network management function has directed this specific address to get off the ring. Turbo 16/4 Token-Ring PC Card 2...
  • Page 101 Error Code Explanation Action Ring Poll, Signal Loss: The PC Card has detected a 1 and 2a 250-ms signal loss (receiver cannot recognize signal) indicating that an error condition has occurred since the PC Card successfully completed the ring signal recognition phase of the open operation.
  • Page 102: Transmit Error Codes

    Link not transmitting I frames, status changed from link open Transmit frame length not acceptable Link retransmission in process, buffers free Station ID not acceptable Protocol error, link not in acceptable state for command Turbo 16/4 Token-Ring PC Card 2...
  • Page 103: Appendix D. Lanaidc Parameter Information

    LANAIDC is the command line version of LANAID. It contains all of the function of LANAID without the graphical user interface. Its primary intended users are LAN administrators and other users who want to duplicate a certain IBM Turbo 16/4 Token-Ring PC Card 2 configuration on multiple computers.
  • Page 104: Lanaidc Parameters

    /RSPROMPT=Y or /RSPROMPT=N - enable Ring Speed Prompt /SOCKET=<x> - specify socket letter (Point Enabler only) /VIEW - view the current configuration /? - display abbreviated help /H or /HELP - display extended help Turbo 16/4 Token-Ring PC Card 2...
  • Page 105: Appendix E. Token.lan And Lan Client Driver Parameters

    The numbef of adapter service access points that can be open at one time. This parameter is not used in the ODI environment and should not be used unless an application specifically requires it. © Copyright IBM Corp. 1997, 1999...
  • Page 106 The base address of the I/O port the adapter uses. The adapter requires 4 contiguous I/O ports. NIC_UAA Default: None Range: hexadecimal string 1-FFFFFFFFFFFFh (Version 3.21) This parameter selects the adapter to initialize by its universally administered address (UAA), which is in read-only storage on the card. Turbo 16/4 Token-Ring PC Card 2...
  • Page 107 Enhanced-mode adapters can be located at most addresses and can be selected by either their UAA or ofdinal number (1=lowest UAA, 2=highest UAA). RECEIVEBUFFERSIZE Default: Varies with mode. Range: 192-2048 (Version 3.33) Changes the adapter shallow-mode receive buffer size. Allows tuning of receive buffers to more closely match the LAN traffic environment.
  • Page 108 Turbo 16/4 Token-Ring PC Card 2...
  • Page 109: Appendix F. Parts Information

    PC Card Cable 73G8314 STP Connector (RJ-45 for Data Connector); converts RJ-45 to Token-Ring 73G2305 RJ-11 to RJ-45 Modular Adapter To order these items, call the IBM Maintenance Parts and Warranty Center 1-800-388-7080 (United States only). © Copyright IBM Corp. 1997, 1999...
  • Page 110 Turbo 16/4 Token-Ring PC Card 2...
  • Page 111: Appendix G. Notices And Warranty

    References in this publication to IBM products, programs, or services do not imply that IBM intends to make these available in all countries in which IBM operates. Any reference to an IBM product, program, or service is not intended to state or imply that only IBM’s product, program, or service may be used.
  • Page 112: Industry Canada Class B Emission Compliance Statement

    IBM cannot accept responsibility for any failure to satisfy the protection requirements resulting from a non-recommended modification of the product, including the fitting of non-IBM option cards. This product has been tested and found to comply with the limits for Class B Information Technology Equipment according to CISPR 22 / European Standard EN 55022.
  • Page 113: Trademarks

    The warranties provided by IBM in this Statement of Limited Warranty apply only to Machines you originally purchase for your use, and not for resale, from IBM or an IBM authorized reseller. The term “Machine” means an IBM machine, its features, conversions, upgrades, elements, or accessories, or any combination of them. Machines are subject to these terms only if purchased in the United States or Puerto Rico, or Canada, and located in the country of purchase.
  • Page 114 For a feature, conversion, or upgrade, IBM or your reseller may require that the Machine on which it is installed be 1) the designated, serial-numbered Machine and 2) at an engineering-change level compatible with the feature, conversion, or upgrade.
  • Page 115 Limitation of Liability Circumstances may arise where, because of a default on IBM’s part (including fundamental breach) or other liability (including negligence and misrepresentation), you are entitled to recover damages from IBM. In each such instance, regardless of the basis on which you are entitled to claim damages, IBM is liable only for: 1.
  • Page 116 Turbo 16/4 Token-Ring PC Card 2...
  • Page 117: Glossary Of Terms And Abbreviations

    The unit of transmission in some LANs, network. including the IBM Token-Ring Network and the IBM PC Network. It includes delimiters, control characters, information, and checking characters. On a Token-Ring network, a frame is created from a token when the token has data appended to it.
  • Page 118 Synonymous with fixed disk drive, hard drive. LAN Client. IBM LAN Client is a protocol stack that operates in protected mode in the DOS TCP/IP, Novell hot plugging. The ability to remove your adapter as IPX Client, NetBIOS, and IEEE 802.2 environments.
  • Page 119 A execution of programs. An operating system may ring of an IBM Token-Ring Network is referred to as a provide services such as resource allocation, LAN segment or as a Token-Ring Network segment.
  • Page 120 The IBM Token-Ring Network is a baseband LAN with a star-wired ring topology that passes tokens from network adapter to network adapter. A network that uses a ring topology, in which tokens are passed in a sequence from node to node.
  • Page 121: Index

    ODI 16–bit parameters 29 open error codes 83 OS/2 26 IBM PC hotline 50 Error Codes 62 IBM Turbo 16/4 Token-Ring PC Card 2 1 OS/2 NDIS 2 device driver 26 IBMTOKCS.DOS 49 OS/2 NDIS device driver 27 IEEE 802.2 1...
  • Page 122 39 software 37 configuration 37 interface 37 software configuration 37 software packages 45 statement of limited warranty 97 STP 5 support 50 TCP/IP Version 1.2 for OS/2 27 TCP/IP Version 2.0 for OS/2 27 Turbo 16/4 Token-Ring PC Card 2...