Macro Functions - Keypad Mode (P-12 = 1 Or 2); Macro Functions - Fieldbus Control Mode; Or 9) - Invertek Drives OPTIDRIVE E3 User Manual
Ac variable speed drive 0.37kw–22kw / 0.5hp–30hp 110–480v 3 phase input
Hide thumbs
Also See for OPTIDRIVE E3:
- User manual (40 pages) ,
- Service manual (23 pages) ,
- Service manual (18 pages)
Table of Contents
Advertisement
7.5. Macro Functions - Keypad Mode (P-12 = 1 or 2)
P-15
0
0
STOP
1
STOP
2
STOP
3
STOP
4
STOP
5
STOP
6
STOP
7
STOP
8
STOP
14
STOP
15
STOP
16
STOP
17
STOP
18
STOP
7.6. Macro Functions - Fieldbus Control Mode (P-12 = 3, 4, 7, 8 or 9)
P-15
0
0
STOP
1
STOP
3
STOP
5
STOP
6
STOP
7
STOP
14
STOP
15
STOP
16
STOP
17
STOP
7
18
STOP
40 | Optidrive ODE-3 IP66 Outdoor Rated User Guide | Version 1.00
DI1
DI2
1
0
ENABLE
-
INC SPD
ENABLE
ENABLE
-
INC SPD
INC SPD
ENABLE
-
ENABLE
-
INC SPD
FWD
ENABLE
ENABLE
FWD
RUN FWD
STOP
RUN REV
^---------FAST STOP (P-24)---------^
RUN FWD
STOP
RUN REV
RUN
-
RUN
PR REF
RUN
P-23 REF
RUN
KPD REF
RUN
AI1 REF
9, 10, 11, 12, 13 = Behavior as per setting 0
DI1
DI2
1
0
ENABLE
FB REF (Fieldbus Speed Reference, Modbus RTU / CAN / Master-Slave
ENABLE
ENABLE
FB REF
ENABLE
FB REF
^----START (P-12 = 3 or 4 Only)----^
ENABLE
FB REF
^----START (P-12 = 3 or 4 Only)----^
ENABLE
FB REF
^----START (P-12 = 3 or 4 Only)----^
ENABLE
-
ENABLE
PR REF
ENABLE
P-23 REF
ENABLE
FB REF
ENABLE
AI1 REF
2, 4, 8, 9, 10, 11, 12, 13 = Behavior as per setting 0
DI3 / AI2
1
0
-
DEC SPD
^----------------START----------------^
PI Speed Reference
-
DEC SPD
^----------------START----------------^
E-TRIP
OK
^-------------------------------START-------------------------------^
KPD REF
AI1 REF
REV
KPD REF
AI1 REF
REV
E-TRIP
OK
E-TRIP
OK
KPD REF
AI1 REF
-
E-TRIP
OK
KPD REF
Fire Mode
KPD REF
Fire Mode
P-23 REF
Fire Mode
KPD REF
Fire Mode
DI3 / AI2
1
0
defined by P-12)
PI Speed Reference
P-20 REF
E-TRIP
OK
PR REF
P-20
P-21
AI1 REF
E-TRIP
OK
KPD REF
E-TRIP
OK
-
E-TRIP
OK
FB REF
Fire Mode
FB REF
Fire Mode
P-23 REF
Fire Mode
FB REF
Fire Mode
DI4 / AI1
1
0
1
FWD
REV
KPD REF
P-20 REF
DEC SPD
-
AI1
AI1
KPD REF
P-20 REF
KPD REF
P-20 REF
AI1
-
-
P-23
P-21
FWD
REV
FWD
REV
AI1
DI4 / AI1
1
0
1
Analog Input AI1
Analog Input AI1
Analog Input AI1
Analog Input AI1
Analog Input AI1
P-23
P-21
Analog Input AI1
Analog Input AI1
Analog Input AI1
www.invertekdrives.com
Diagram
8
8
9
10
1
1 1
1 1
2
2
2
1
Diagram
14
15
3
1
3
3
16
2
1
1
1
Hide quick links:
Advertisement
Table of Contents
Related Manuals for Invertek Drives OPTIDRIVE E3
Related Products for Invertek Drives OPTIDRIVE E3
- Invertek Drives eco OPTIDRIVE
- Invertek Drives Optidrive E3 ODE-3 Series
- Invertek Drives Optidrive ODP-2
- Invertek Drives Optidrive Plus 3GV Compact
- Invertek Drives Optidrive Compact 2-Basic OPC-2 E Series
- Invertek Drives Eco Optidrive Series
- Invertek Drives elevator CORE
- Invertek Drives Optidrive HVAC Series
Need help?
Do you have a question about the OPTIDRIVE E3 and is the answer not in the manual?
Questions and answers
Hi, problem with max speed p-01 50.0 p-02 0.0 p-03 5.0 only reaching 25.0 max speed 230v input 178v between phases output **** and cabling replaced many thanks
The Optidrive E3 may be limited to a maximum speed of 25.0 due to one or more of the following reasons:
1. Speed Reference Input (P00-03) – The speed reference input might be lower than expected, causing the drive to operate at a reduced speed.
2. Current Limit Reduction – If the overload accumulator reaches 90%, the output current limit is reduced to 100% of P-08, which could restrict the speed.
3. Analog Input Scaling – If an analog input is used for speed control, its scaling or signal level might be affecting the speed.
4. Alternative Ramp Time (P-24) – If P-24 is set and conditions apply, it could be affecting acceleration and deceleration speeds.
5. Derating at High Altitude or Temperature – If the drive is operating above 1000m or in high ambient temperatures, it may be derated, limiting performance.
Checking these factors and adjusting settings accordingly should help resolve the speed limitation.
This answer is automatically generated