Table Of Contents - Bard MULTI-TEC W24AAPA Installation Instructions Manual

CONTENTS
MULTI-TEC/LC6000 INSTALLATION/SET UP
General Information ...........................................5
List of Necessary Materials/Tools ....................8
Site Preparation ...................................................9
Model Identification .......................................... 9
New Shelter Installation vs. Retrofit Installation .. 9
Minimum Clearance .......................................... 9
Clearance to Combustibles ................................ 9
Wall-Mount Unit Mounting ..............................11
Mounting the Units ......................................... 11
Supply Air Grill Installation .................................... 12
Wall-Mount Unit Wiring ...................................19
Main Power Wiring .......................................... 19
Low Voltage Wiring ......................................... 19
Preliminary Start Up .........................................23
Running in Stand Alone (Orphan) Mode ............ 23
LC6000 Controller Installation ........................24
LC6000 Controller .......................................... 25
Mounting the LC Controller ....................... 25
Installing Remote Indoor
Temperature/Humidity Sensor(s) ................ 26
FIGURES AND TABLES
Figure 1 MULTI-TEC Model Nomenclature .............8
Figure 2 Dimensions ..........................................10
Figure 3 Outdoor Sensor Installation .................... 11
Figure 4A W18/24 Mounting Instructions ..............12
Figure 4B W30/36 Mounting Instructions ..............13
Figure 4C W42/48 Mounting Instructions ..............14
Figure 4D W60/72 Mounting Instructions ..............15
Figure 5 Electric Heat Clearance .........................16
Figure 6 Wall Mounting Instructions ....................16
Figure 7 Wall Mounting Instructions ....................17
Figure 8 Common Wall Mounting Installations ......18
Figure 9 Circuit Routing Label ............................19
Figure 10 WIRING: VAC Supply Wiring
Landing Points .....................................19
Figure 11 Cooling and Heating Setpoints ...............23
Figure 12 Typical LC6000 Component Location .....24
Figure 13 LC6000 Fused Power Supply Terminal ...24
Figure 14 Remote Indoor Temperature/Humidity
Sensor Installation ................................26
Figure 15 Additional Remote Sensor Installation ....27
Figure 16 Smoke Detector, Hydrogen Detector
and Generator Run Connections .............28
Figure 17 Communication Wiring (Daisy Chain) ......29
Figure 18 Communication Wiring (Alt. Method) ......29
Figure 19 Placement of Communication Filters ......30
Figure 20 Communication Wiring: Termination
at the Controller ...................................31
Figure 21 Communication Wiring: Termination
at the First Wall-Mount Unit ..................32
Figure 22 Communication Wiring: Termination
at Additional Wall-Mount Units ..............33
Figure 23 LC6000 Controller Circuit Install ...........34
Manual 2100-676B
Page 4 of 88
Smoke. Hydrogen and Generator Alarms ..... 28
Communication Wiring .............................. 29
Supply Wiring .......................................... 34
System Set Up ....................................................37
TEC-EYE Hand-Held Diagnostic Tool ................ 37
TEC-EYE Status Screen ............................ 38
Setting Up Wall-Mount Units for Operation ....... 38
1. Address Each Wall-Mount Unit .............. 38
2. Execute a Run Test on Each Unit ........... 38
3. Clear Unit Alarm Logs on Each Unit ....... 39
Setting Up LC6000 for Operation .................... 39
4. Set LC Controller Date and Time ............ 39
5. Configure Sensors................................. 40
6. Enter Total Number of Units .................. 42
7. Verify Units are Online .......................... 42
8. Clear Controller Alarm Logs ................... 43
9. Complete Installation ............................ 43
Additional Information ....................................44
Menu Screens and Password Levels.................. 44
Setpoints ....................................................... 44
Calibrating Sensors ......................................... 44
Figure 24 Controller Grounding Posts ....................34
WIRING: LC6000 Wiring Diagram ..........36
Figure 25
Figure 26 TEC-EYE Connection to Unit Control ......37
Figure 27 TEC-EYE Display and Interface ..............37
Figure 28 Unit Configuration ................................38
Figure 29 Executing Run Test ...............................39
Figure 30 Clearing Unit Alarm Logs .......................39
Figure 31 Setting Controller Date and Time ............40
Figure 32 Enable/Disable Zone 1 Indoor
Humidity Sensor ...................................40
Figure 33 LC6000 Controller Display and Interface ...40
Figure 34 Enable/Disable Zone 2 Indoor
Humidity Sensor ...................................41
Figure 35 Enable/Disable Zone 3 Indoor
Humidity Sensor ...................................41
Figure 36 Enable/Disable Zone 1 Indoor
Temperature Sensor ..............................41
Figure 37 Enable/Disable Zone1 Remote
Temperature Sensor ..............................41
Figure 38 Enable/Disable Zone 2 Remote
Temperature Sensor ..............................42
Figure 39 Enable/Disable Zone 3 Remote
Temperature Sensor ..............................42
Figure 40 Total Units Displayed ............................42
Figure 41 Clearing LC6000 Alarm Logs .................43
Figure 42 Adjusting Sensor Offset Value ................44
Table 1 W**A*P Series Electrical Specifications .20
Table 2 W**L*P Series Electrical Specifications ..21
Table 3 W**A*E Series Electrical Specifications .22
Table 4 LC6000-100 Terminal Block Index ........35
Table 5 LC6000/TEC-EYE Passwords (Default) ....37
Table 6 MULTI-TEC Unit Status Messages ..........45
Table 7 LC6000 Status Messages ......................45