Making A Tone's Delay Time Match The System Tempo; Using A Pedal Switch To Modify The Rotary Speed Of The Rotary Effect; Playing Phrase Loops At A System's Tempo - Roland XV-5080. Owner's Manual

Chapter 10 Examples of Applications Using the XV-5080
64:STEREO PHASER2
65:STEREO AUTO WAH
66:ST FORMANT FILTER
67:MULTI TAP DELAY 2
68:REVERSE DELAY 2
69:SHUFFLE DELAY 2
70:3D DELAY 2
71:ROTARY 2
72:ROTARY MULTI
73:KEYBOARD MULTI
74:RHODES MULTI
81:GUITAR MULTI A
82:GUITAR MULTI B
83:GUITAR MULTI C
84:CLEAN GUITAR MULTI A Delay Left/Right,CF Rate
85:CLEAN GUITAR MULTI B AW Rate,Delay Left/Right,
86:BASS MULTI
89:3D AUTO SPIN
Here is an example in which STEP FLANGER is used for the
Multi-effects.
1. Select a Patch on the PATCH PLAY page.
2. Set the Patch Clock Source parameter (PATCH Common
General #2 page) to "SYSTEM."
3. Make sure that MFX Type (PATCH Effects General page)
is set to STEP FLANGER.
If not, reset it so that it is.
4. Make sure that Step Rate (PATCH Effects MFX page) is
set to a note—not a numerical—value.
If not, reset using a note value.
5. Set the System Clock Source parameter (SYSTEM
General #1 page) to "INT."
* When System Clock Source is set to "MIDI," you can
synchronize the Multi-effect to the tempo of an external MIDI
device.
220
Rate,Step Rate
Rate
Rate
Delay1-4
Delay1-4
Delay
Delay Left/Right/Center
Woofer Speed Slow/
Fast,Tweeter Speed Slow/
Fast
Rotary High/Low Slow
Rate,Rotary High/Low Fast
Rate
Phaser Rate,Delay Time
Left/Right
Phaser Rate,CF Rate,TP Rate
Delay Time Left/Right,CF
Rate
CF Rate
AW Rate,Delay Time Left/
Right,CF Rate
CF Rate
CF Rate
Speed
6. If the System Tempo (SYSTEM General #1 page)
changes, the LFO Rate changes along with it.
Making a Tone's Delay Time
Match the System Tempo
* You can use the Tone Delay only with Four-Tone Patches.
1. Select a Patch on the PATCH PLAY page.
2. Set the Patch Clock Source parameter (PATCH Common
General #2 page) to "SYSTEM."
3. Set the Time parameter (PATCH WG Parameter page) of
Tone Delay to the beat length for the tempo you are
synchronizing.
If not, reset it so that it is.
4. Set the System Clock Source parameter (SYSTEM
General #1 page) to "INT."
* When System Clock Source is set to "MIDI," you can
synchronize the Multi-effect to the tempo of an external MIDI
device.
5. If the System Tempo (SYSTEM General #1 page)
changes, the LFO Rate changes along with it.
Using a Pedal Switch to Modify
the Rotary Speed of the Rotary
Effect
1. Connect a pedal switch (DP-2, DP-6, etc.) to your
external device (MIDI keyboard, etc.).
2. Set the pedal switch of the external MIDI device to
generate FOOT TYPE (CC4) control-change messages.
To learn how to set up the pedal switch, refer to the external
MIDI device's owner's manual.
3. Select "PR-A: 050 Perky B" on the PATCH PLAY page.
This Patch uses ROTARY as its Multi-effect.
4. Go to the PATCH Effects MFX Control page and set
Source of MFX Control 1 to "FOOT TYPE."
5. Set Destination to "SPEED," and Sens to "+63."
When you wish to speed up the rotary effect, press the pedal
switch. Release the pedal switch to slow down the rotary
effect.
Playing Phrase Loops at a
System's Tempo
An optional Wave Expansion Board can contain Patches
based on waveforms that are timed—in BPM—phrase loops.